--===============8270145392479978268==
boundary="----=_Part_662751_2087167494.1474260098751"
------=_Part_662751_2087167494.1474260098751
Content-Transfer-Encoding: quoted-printable
Dr. Mayf- those bulbs you powered and then grounded but they still didn't l=
ight up...... Have you used your VOM to make sure those bulbs are still goo=
d? After all they aren't close to new. Joe Valence has a new set up I plan =
on buy when I install my new dash which has much brighter bulbs, including =
brake and tail light. I know you are back to the size 10 hands if U exchang=
ed the bulbs but I think it is still a good investment,as always, TonytheTi=
ger=C2=A0Tony Lang (TtT)
From: Cars via Tigers <tigers@autox.team.net>
To: Larry Mayfield <drmayf@mayfco.com>=20
Cc: tigers@autox.team.net
Sent: Sunday, September 18, 2016 7:11 PM
Subject: Re: [Tigers] Dash Pieces
=20
Tom Hall sells a very nice solid state voltage stabilizer. I would recommen=
d his. I have one in my car. Also, the lights DO NOT run through the stabil=
izer=C2=A0
Lynn
Sent from my mobile device
On Sep 18, 2016, at 10:06 AM, Larry Mayfield via Tigers <tigers@autox.team.=
net> wrote:
#yiv3309024102 #yiv3309024102 -- _filtered #yiv3309024102 {panose-1:2 4 5 3=
5 4 6 3 2 4;} _filtered #yiv3309024102 {font-family:Calibri;panose-1:2 15 =
5 2 2 2 4 3 2 4;}#yiv3309024102 #yiv3309024102 p.yiv3309024102MsoNormal, #y=
iv3309024102 li.yiv3309024102MsoNormal, #yiv3309024102 div.yiv3309024102Mso=
Normal {margin:0in;margin-bottom:.0001pt;font-size:12.0pt;}#yiv3309024102 a=
:link, #yiv3309024102 span.yiv3309024102MsoHyperlink {color:#0563C1;text-de=
coration:underline;}#yiv3309024102 a:visited, #yiv3309024102 span.yiv330902=
4102MsoHyperlinkFollowed {color:#954F72;text-decoration:underline;}#yiv3309=
024102 span.yiv3309024102EmailStyle18 {color:#1F497D;}#yiv3309024102 .yiv33=
09024102MsoChpDefault {font-size:10.0pt;} _filtered #yiv3309024102 {margin:=
1.0in 1.0in 1.0in 1.0in;}#yiv3309024102 div.yiv3309024102WordSection1 {}#yi=
v3309024102 Mark, perhaps that is part of my problem, But, my wiring schema=
tic shows the dash instrument lights coming from the panel light switch, wh=
ich gets its power from the main light switch. =C2=A0The only thing my sche=
matic shows coming from the instrument regulator are the 10 volts to the in=
tank fuel level resistance and to the temp sensor resistor. =C2=A0Nothing =
going to lights at all. But the voltage stabilizer may indeed be farkled. W=
hen powered on, the fuel gage reads full and when off, slowly returns to 0 =
. The temp gage does not do anything. As to dash lights, I have even tried =
putting voltage on the red with white stripe wire and grounding a bulbs soc=
ket to see if that light =C2=A0works. Nothing. =C2=A0=C2=A0 =C2=A0I will se=
e if I can get the stabilizer out and check its functionality. I suspect th=
at I might be able to do that without removing it though? Like v=3Dusing a =
voltmeter on the GB wire from the =3Dstabilizer to ground.=C2=A0 Yeah, I=E2=
=80=99ll give that a try.=C2=A0 =C2=A0Sure will be great to get dash light=
s and the temp and fuel gages working! Last items on my list. Part of my [p=
roblem stems from a long latency between when it was apart and now. I do re=
member that when I replaced the old dash that when I removed a gauge I put =
the wires back on in the same place so that when I put the new wood in ever=
ything, I thought, went back in the same location and terminal. =C2=A0Many=
thanks for the suggestions, new avenues to test! =C2=A0mayf =C2=A0From: C=
oolVT@aol.com [mailto:CoolVT@aol.com]=20
Sent: Sunday, September 18, 2016 6:56 AM
To: drmayf@mayfco.com; tigers@autox.team.net
Subject: Re: [Tigers] Dash Pieces =C2=A0Mayf,Pretty sure the power to the g=
auges and dash lights come from the voltage stabilizer.=C2=A0 It's a little=
squarish, metal device about 2"x2" and is screwed to the support column th=
at goes from the dash to the firewall (just to the right of the steering co=
lumn). If you pull the wires off=C2=A0 be sure to label where each goes bec=
ause the color coding of the wires will probably be faded. Not sure of a so=
urce for the stabilizer if that's the problem.Mark L=C2=A0In a message date=
d 9/18/2016 4:15:19 A.M. Eastern Daylight Time, tigers@autox.team.net write=
s:
<image001.jpg>Ok, I am replacing and adding a couple of dash switches to my=
car.=C2=A0 The pieces I need are the chrome screw on switch bezel for use =
on the wood dash.=C2=A0 Is there a source for such?=C2=A0 I have the switch=
es but sadly they do not come with them.=C2=A0 =C2=A0And I am having the d=
ickens of a time with the instruments: mostly with the dash lights. I know =
grounds are the typical source or cause of the problems and I have been att=
acking that as best I can. =C2=A0Also there does not seem to be power to th=
at circuit, even when I turn the lights on and the panel switch as well.=C2=
=A0 I replaced the fuse block and that did help. More voltage. Was pretty c=
orroded. New one has a spiffy cover and I applied dielectric grease as well=
. =C2=A0The wipers work, the horn honks the heater motor runs, have oil pre=
ssure, but no dash light or fuel level or temp. Also purchased a brake ligh=
t switch as well. Turn signals work as does the green indicator light on th=
e dash. Head lights ( high and low beams), turn signals and stop light all =
work. Part of the issue is size 100 hands (big) in a size 3 under dash. =C2=
=A0So I am going to keep after it.=C2=A0 Was there an wiring change in the =
MK1 production run? The wiring on my gas and temp gages does not look like =
the schematic. =C2=A0If I look at the back side of the fuel gage and temp g=
age what wire goes where? =C2=A0Some remote help needed here=E2=80=A6 at le=
ast some advice or comment. =C2=A0mayf _________________________
drmayf
Worlds Fastest Sunbeam, period.
204.913 mph flying mile
210.779 mph exit (not top)=C2=A0 speed =C2=A0
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/coolvt@aol.com
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/cars@wt-inc.com
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/achd73@yahoo.com
=20
------=_Part_662751_2087167494.1474260098751
Content-Transfer-Encoding: quoted-printable
<html><head></head><body><div style=3D"color:#000; background-color:#fff; f=
ont-family:Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif;font=
-size:16px"><div id=3D"yui_3_16_0_1_1474135213603_60867"><span id=3D"yui_3_=
16_0_1_1474135213603_61248">Dr. Mayf- those bulbs you powered and then grou=
nded but they still didn't light up...... Have you used your VOM to make su=
re those bulbs are still good? After all they aren't close to new. Joe Vale=
nce has a new set up I plan on buy when I install my new dash which has muc=
h brighter bulbs, including brake and tail light. I know you are back to th=
e size 10 hands if U exchanged the bulbs but I think it is still a good inv=
estment,</span></div><div id=3D"yui_3_16_0_1_1474135213603_60867" dir=3D"lt=
r"><span>as always, TonytheTiger</span></div><div></div><div id=3D"yui_3_16=
_0_1_1474135213603_60862"> </div><div class=3D"signature" id=3D"yui_3_=
16_0_1_1474135213603_60860"><div id=3D"yui_3_16_0_1_1474135213603_60859">To=
ny Lang (TtT)<var id=3D"yui-ie-cursor"></var></div></div><div class=3D"qtdS=
eparateBR" id=3D"yui_3_16_0_1_1474135213603_60850"><br><br></div><div class=
=3D"yahoo_quoted" id=3D"yui_3_16_0_1_1474135213603_60854" style=3D"display:=
block;"> <div style=3D"font-family: Helvetica Neue, Helvetica, Arial, Luc=
ida Grande, sans-serif; font-size: 16px;" id=3D"yui_3_16_0_1_1474135213603_=
60853"> <div style=3D"font-family: HelveticaNeue, Helvetica Neue, Helvetica=
, Arial, Lucida Grande, sans-serif; font-size: 16px;" id=3D"yui_3_16_0_1_14=
74135213603_60852"> <div dir=3D"ltr" id=3D"yui_3_16_0_1_1474135213603_60851=
"> <font size=3D"2" face=3D"Arial" id=3D"yui_3_16_0_1_1474135213603_60857">=
<hr size=3D"1" id=3D"yui_3_16_0_1_1474135213603_60856"> <b><span style=3D"=
font-weight:bold;">From:</span></b> Cars via Tigers <tigers@autox.team.n=
et><br> <b><span style=3D"font-weight: bold;">To:</span></b> Larry Mayfi=
eld <drmayf@mayfco.com> <br><b><span style=3D"font-weight: bold;">Cc:=
</span></b> tigers@autox.team.net<br> <b><span style=3D"font-weight: bold;"=
>Sent:</span></b> Sunday, September 18, 2016 7:11 PM<br> <b><span style=3D"=
font-weight: bold;">Subject:</span></b> Re: [Tigers] Dash Pieces<br> </font=
> </div> <div class=3D"y_msg_container"><br><div id=3D"yiv3309024102"><div>=
<div><div style=3D"direction:inherit;">Tom Hall sells a very nice solid sta=
te voltage stabilizer. I would recommend his. I have one in my car. Also, t=
he lights DO NOT run through the stabilizer </div><div style=3D"direct=
ion:inherit;"><br clear=3D"none"></div><div style=3D"direction:inherit;">Ly=
nn</div><br clear=3D"none">Sent from my mobile device</div><div><br clear=
=3D"none">On Sep 18, 2016, at 10:06 AM, Larry Mayfield via Tigers <<a re=
l=3D"nofollow" shape=3D"rect" ymailto=3D"mailto:tigers@autox.team.net"; targ=
et=3D"_blank" href=3D"mailto:tigers@autox.team.net";>tigers@autox.team.net</=
a>> wrote:<br clear=3D"none"><br clear=3D"none"></div><blockquote type=
=3D"cite"><div></div></blockquote></div><style>#yiv3309024102 #yiv330902410=
2 --
=20
_filtered #yiv3309024102 {panose-1:2 4 5 3 5 4 6 3 2 4;}
_filtered #yiv3309024102 {font-family:Calibri;panose-1:2 15 5 2 2 2 4 3 2 =
4;}
#yiv3309024102 =20
#yiv3309024102 p.yiv3309024102MsoNormal, #yiv3309024102 li.yiv3309024102Mso=
Normal, #yiv3309024102 div.yiv3309024102MsoNormal
=09{margin:0in;margin-bottom:.0001pt;font-size:12.0pt;}
#yiv3309024102 a:link, #yiv3309024102 span.yiv3309024102MsoHyperlink
=09{color:#0563C1;text-decoration:underline;}
#yiv3309024102 a:visited, #yiv3309024102 span.yiv3309024102MsoHyperlinkFoll=
owed
=09{color:#954F72;text-decoration:underline;}
#yiv3309024102 span.yiv3309024102EmailStyle18
=09{color:#1F497D;}
#yiv3309024102 .yiv3309024102MsoChpDefault
=09{font-size:10.0pt;}
_filtered #yiv3309024102 {margin:1.0in 1.0in 1.0in 1.0in;}
#yiv3309024102 div.yiv3309024102WordSection1
=09{}
#yiv3309024102 </style><div><div class=3D"yiv3309024102WordSection1"><div c=
lass=3D"yiv3309024102MsoNormal"><span style=3D"color:#1F497D;">Mark, perhap=
s that is part of my problem, But, my wiring schematic shows the dash instr=
ument lights coming from the panel light switch, which gets its power from =
the main light switch. The only thing my schematic shows coming from =
the instrument regulator are the 10 volts to the in tank fuel level resista=
nce and to the temp sensor resistor. Nothing going to lights at all. =
But the voltage stabilizer may indeed be farkled. When powered on, the fuel=
gage reads full and when off, slowly returns to 0 . The temp gage does not=
do anything. </span></div><div class=3D"yiv3309024102MsoNormal"><span styl=
e=3D"color:#1F497D;">As to dash lights, I have even tried putting voltage o=
n the red with white stripe wire and grounding a bulbs socket to see if tha=
t light works. Nothing. </span></div><div class=3D"yiv330=
9024102MsoNormal"><span style=3D"color:#1F497D;"> </span></div><div c=
lass=3D"yiv3309024102MsoNormal"><span style=3D"color:#1F497D;">I will see i=
f I can get the stabilizer out and check its functionality. I suspect that =
I might be able to do that without removing it though? Like v=3Dusing a vol=
tmeter on the GB wire from the =3Dstabilizer to ground. Yeah, I=E2=80=
=99ll give that a try. </span></div><div class=3D"yiv3309024102MsoNor=
mal"><span style=3D"color:#1F497D;"> </span></div><div class=3D"yiv33=
09024102MsoNormal"><span style=3D"color:#1F497D;">Sure will be great to get=
dash lights and the temp and fuel gages working! Last items on my list. Pa=
rt of my [problem stems from a long latency between when it was apart and n=
ow. I do remember that when I replaced the old dash that when I removed a g=
auge I put the wires back on in the same place so that when I put the new w=
ood in everything, I thought, went back in the same location and terminal. =
</span></div><div class=3D"yiv3309024102MsoNormal"><span style=3D"color:#1F=
497D;"> </span></div><div class=3D"yiv3309024102MsoNormal"><span styl=
e=3D"color:#1F497D;">Many thanks for the suggestions, new avenues to test!<=
/span></div><div class=3D"yiv3309024102MsoNormal"><span style=3D"color:#1F4=
97D;"> </span></div><div class=3D"yiv3309024102MsoNormal"><span style=
=3D"color:#1F497D;">mayf </span></div><div class=3D"yiv3309024102MsoNormal"=
><a rel=3D"nofollow" shape=3D"rect" name=3D"_MailEndCompose" href=3D""><spa=
n style=3D"color:#1F497D;"> </span></a></div><div><div style=3D"borde=
r:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0in 0in 0in;"><div clas=
s=3D"yiv3309024102MsoNormal"><b><span style=3D"font-size:11.0pt;">From:</sp=
an></b><span style=3D"font-size:11.0pt;"> <a rel=3D"nofollow" shape=3D"rect=
" ymailto=3D"mailto:CoolVT@aol.com"; target=3D"_blank" href=3D"mailto:CoolVT=
@aol.com">CoolVT@aol.com</a> [<a rel=3D"nofollow" shape=3D"rect" ymailto=3D=
"mailto:CoolVT@aol.com"; target=3D"_blank" href=3D"mailto:CoolVT@aol.com";>ma=
ilto:CoolVT@aol.com</a>] <br clear=3D"none"><b>Sent:</b> Sunday, September =
18, 2016 6:56 AM<br clear=3D"none"><b>To:</b> <a rel=3D"nofollow" shape=3D"=
rect" ymailto=3D"mailto:drmayf@mayfco.com"; target=3D"_blank" href=3D"mailto=
:drmayf@mayfco.com">drmayf@mayfco.com</a>; <a rel=3D"nofollow" shape=3D"rec=
t" ymailto=3D"mailto:tigers@autox.team.net"; target=3D"_blank" href=3D"mailt=
o:tigers@autox.team.net">tigers@autox.team.net</a><br clear=3D"none"><b>Sub=
ject:</b> Re: [Tigers] Dash Pieces</span></div></div></div><div class=3D"yi=
v3309024102MsoNormal"> </div><div><div class=3D"yiv3309024102MsoNorma=
l"><strong><span style=3D"">Mayf,</span></strong><span style=3D""></span></=
div></div><div><div class=3D"yiv3309024102MsoNormal"><strong><span style=3D=
"">Pretty sure the power to the gauges and dash lights come from the voltag=
e stabilizer. It's a little squarish, metal device about 2"x2" and is=
screwed to the support column that goes from the dash to the firewall (jus=
t to the right of the steering column). If you pull the wires off be =
sure to label where each goes because the color coding of the wires will pr=
obably be faded. Not sure of a source for the stabilizer if that's the prob=
lem.</span></strong><span style=3D""></span></div></div><div><div class=3D"=
yiv3309024102MsoNormal"><strong><span style=3D"">Mark L</span></strong><spa=
n style=3D""></span></div></div><div><div class=3D"yiv3309024102MsoNormal">=
<span style=3D""> </span></div></div><div><div><div class=3D"yiv330902=
4102MsoNormal"><span style=3D"">In a message dated 9/18/2016 4:15:19 A.M. E=
astern Daylight Time, <a rel=3D"nofollow" shape=3D"rect" ymailto=3D"mailto:=
tigers@autox.team.net" target=3D"_blank" href=3D"mailto:tigers@autox.team.n=
et">tigers@autox.team.net</a> writes:</span></div></div><blockquote style=
=3D"border:none;border-left:solid blue 1.5pt;padding:0in 0in 0in 4.0pt;marg=
in-left:3.75pt;margin-top:5.0pt;margin-bottom:5.0pt;"><div class=3D"yiv3309=
024102MsoNormal"><span style=3D"font-size:10.0pt;"><image001.jpg></sp=
an></div><div class=3D"yiv3309024102yqt7437865069" id=3D"yiv3309024102yqtfd=
32324"></div><div class=3D"yiv3309024102yqt7437865069" id=3D"yiv3309024102y=
qtfd38646"><div><div class=3D"yiv3309024102MsoNormal" style=3D""><span styl=
e=3D"color:black;">Ok, I am replacing and adding a couple of dash switches =
to my car. The pieces I need are the chrome screw on switch bezel for=
use on the wood dash. Is there a source for such? I have the s=
witches but sadly they do not come with them. </span></div><div class=
=3D"yiv3309024102MsoNormal" style=3D""><span style=3D"color:black;"> =
</span></div><div class=3D"yiv3309024102MsoNormal" style=3D""><span style=
=3D"color:black;">And I am having the dickens of a time with the instrument=
s: mostly with the dash lights. I know grounds are the typical source or ca=
use of the problems and I have been attacking that as best I can. Als=
o there does not seem to be power to that circuit, even when I turn the lig=
hts on and the panel switch as well. I replaced the fuse block and th=
at did help. More voltage. Was pretty corroded. New one has a spiffy cover =
and I applied dielectric grease as well. The wipers work, the horn ho=
nks the heater motor runs, have oil pressure, but no dash light or fuel lev=
el or temp. Also purchased a brake light switch as well. Turn signals work =
as does the green indicator light on the dash. Head lights ( high and low b=
eams), turn signals and stop light all work. Part of the issue is size 100 =
hands (big) in a size 3 under dash. So I am going to keep after it.&n=
bsp; Was there an wiring change in the MK1 production run? The wiring on my=
gas and temp gages does not look like the schematic. If I look at th=
e back side of the fuel gage and temp gage what wire goes where?</span></di=
v><div class=3D"yiv3309024102MsoNormal" style=3D""><span style=3D"color:bla=
ck;"> </span></div><div class=3D"yiv3309024102MsoNormal" style=3D""><=
span style=3D"color:black;">Some remote help needed here=E2=80=A6 at least =
some advice or comment.</span></div><div class=3D"yiv3309024102MsoNormal" s=
tyle=3D""><span style=3D"color:black;"> </span></div><div class=3D"yi=
v3309024102MsoNormal" style=3D""><span style=3D"color:black;">mayf </span><=
/div><div class=3D"yiv3309024102MsoNormal" style=3D""><span style=3D"font-s=
ize:11.0pt;">_________________________<br clear=3D"none">drmayf<br clear=3D=
"none">Worlds Fastest Sunbeam, period.<br clear=3D"none">204.913 mph flying=
mile<br clear=3D"none">210.779 mph exit (not top) speed</span></div>=
<div class=3D"yiv3309024102MsoNormal" style=3D""><span style=3D"color:black=
;"> </span></div></div><div class=3D"yiv3309024102MsoNormal" style=3D=
"margin-bottom:12.0pt;"><span style=3D"font-size:10.0pt;"><br clear=3D"none=
"><br clear=3D"none">_______________________________________________<br cle=
ar=3D"none"><br clear=3D"none"><a rel=3D"nofollow" shape=3D"rect" ymailto=
=3D"mailto:tigers@autox.team.net"; target=3D"_blank" href=3D"mailto:tigers@a=
utox.team.net">tigers@autox.team.net</a><br clear=3D"none"><br clear=3D"non=
e">Donate: <a rel=3D"nofollow" shape=3D"rect" target=3D"_blank" href=3D"htt=
p://www.team.net/donate.html">http://www.team.net/donate.html</a><br clear=
=3D"none">Archive: <a rel=3D"nofollow" shape=3D"rect" target=3D"_blank" hre=
f=3D"http://www.team.net/archive";>http://www.team.net/archive</a><br clear=
=3D"none">Forums: <a rel=3D"nofollow" shape=3D"rect" target=3D"_blank" href=
=3D"http://www.team.net/forums";>http://www.team.net/forums</a><br clear=3D"=
none">Unsubscribe: <a rel=3D"nofollow" shape=3D"rect" target=3D"_blank" hre=
f=3D"http://autox.team.net/mailman/options/tigers/coolvt@aol.com";>http://au=
tox.team.net/mailman/options/tigers/coolvt@aol.com</a><br clear=3D"none"><b=
r clear=3D"none"></span><span style=3D""></span></div></div></blockquote></=
div></div><blockquote type=3D"cite"><div><div class=3D"yiv3309024102yqt7437=
865069" id=3D"yiv3309024102yqtfd63273"><span>______________________________=
_________________</span><br clear=3D"none"><span></span><br clear=3D"none">=
<span><a rel=3D"nofollow" shape=3D"rect" ymailto=3D"mailto:tigers@autox.tea=
m.net" target=3D"_blank" href=3D"mailto:tigers@autox.team.net";>tigers@autox=
.team.net</a></span><br clear=3D"none"><span></span><br clear=3D"none"><spa=
n>Donate: <a rel=3D"nofollow" shape=3D"rect" target=3D"_blank" href=3D"http=
://www.team.net/donate.html">http://www.team.net/donate.html</a></span><br =
clear=3D"none"><span>Archive: <a rel=3D"nofollow" shape=3D"rect" target=3D"=
_blank" href=3D"http://www.team.net/archive";>http://www.team.net/archive</a=
></span><br clear=3D"none"><span>Forums: <a rel=3D"nofollow" shape=3D"rect"=
target=3D"_blank" href=3D"http://www.team.net/forums";>http://www.team.net/=
forums</a></span><br clear=3D"none"></div><span><div class=3D"yiv3309024102=
yqt7437865069" id=3D"yiv3309024102yqtfd40031">Unsubscribe: </div><a rel=3D"=
nofollow" shape=3D"rect" target=3D"_blank" href=3D"http://autox.team.net/ma=
ilman/options/tigers/cars@wt-inc.com">http://autox.team.net/mailman/options=
/tigers/cars@wt-inc.com</a></span><div class=3D"yiv3309024102yqt7437865069"=
id=3D"yiv3309024102yqtfd87346"><br clear=3D"none"><span></span><br clear=
=3D"none"><span></span><br clear=3D"none"></div></div></blockquote></div></=
div><br><div class=3D"yqt7437865069" id=3D"yqtfd98700">____________________=
___________________________<br clear=3D"none"><br clear=3D"none"><a shape=
=3D"rect" ymailto=3D"mailto:tigers@autox.team.net"; href=3D"mailto:tigers@au=
tox.team.net">tigers@autox.team.net</a><br clear=3D"none"><br clear=3D"none=
">Donate: <a shape=3D"rect" href=3D"http://www.team.net/donate.html"; target=
=3D"_blank">http://www.team.net/donate.html</a><br clear=3D"none">Archive: =
<a shape=3D"rect" href=3D"http://www.team.net/archive"; target=3D"_blank">ht=
tp://www.team.net/archive</a><br clear=3D"none">Forums: <a shape=3D"rect" h=
ref=3D"http://www.team.net/forums"; target=3D"_blank">http://www.team.net/fo=
rums</a><br clear=3D"none">Unsubscribe: <a shape=3D"rect" href=3D"http://au=
tox.team.net/mailman/options/tigers/achd73@yahoo.com" target=3D"_blank">htt=
p://autox.team.net/mailman/options/tigers/achd73@yahoo.com</a><br clear=3D"=
none"><br clear=3D"none"><br clear=3D"none"></div><br><br></div> </div> </d=
iv> </div></div></body></html>
------=_Part_662751_2087167494.1474260098751--
--===============8270145392479978268==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net
--===============8270145392479978268==--
|