Its like Rich and Alan said,
That`s the way to do and that was the way and (as far as I know ) it was done
at Warwick. As there was no other bracket in the LeMans kit and what they have
done at the Cape was very pragmatic to say, they just used the old bracket and
a file to enlarge the holes.
Josef Eckert
Konigswinter/Germany
-----Urspr|ngliche Nachricht-----
Von: healeys-bounces@autox.team.net [mailto:healeys-bounces@autox.team.net] Im
Auftrag von Alan Seigrist
Gesendet: Montag, 1. August 2011 16:00
An: Thomas Willig; Rich Chrysler; healeys@autox.team.net
Betreff: Re: [Healeys] Looking for 100M Choke abutment bracket
Thomas -
Sounds too complicated! I just opened up the holes a bit like Rich said, that
was all I needed. Fit right up. I eventually switched back again (I like the
plain jane cars)..
Alan
On 8/1/11, Thomas Willig <twillig@ruda.de> wrote:
> Rich,
>
> no that's not the case (as far as I see it-enlightenment very
> welcome). The angle of the bracket has to be changed as well. Doing
> this, you have to cut the bracket were the abutment pin (the pin that
> fixes the outer control cable to the bracket) goes through the
> bracket.
>
>
> Thomas
>
>
> -----Urspr|ngliche Nachricht-----
> Von: Rich Chrysler [mailto:richchrysler@quickclic.net]
> Gesendet: Montag, 1. August 2011 14:28
> An: Thomas Willig
> Cc: healeys@autox.team.net
> Betreff: RE: [Healeys] Looking for 100M Choke abutment bracket
>
> Thomas,
>
> I was under the impression it is the same bracket but the end mounting
> holes are opened up a bit to fit the H6 setup.
>
> Rich
>
> -----Original Message-----
> From: healeys-bounces@autox.team.net
> [mailto:healeys-bounces@autox.team.net]
> On Behalf Of Thomas Willig
> Sent: 2011-08-01 4:03
> To: healeys@autox.team.net
> Subject: [Healeys] Looking for 100M Choke abutment bracket
>
> Hello,
>
>
>
> can someone enlighten me were I can get a choke abutment bracket for
> the 100M? I am talking about the small steel strip of flat steel that
> goes over the entire opening between the two H6 carbs and is held
> there by the two bolts for the cold air box. The dimensions of this
> bracket differ from the one used for the standard h4 setup.
> Regards
>
>
> Thomas Willig
> _______________________________________________
> _______________________________________________
> Healeys@autox.team.net
> Donate: http://www.team.net/donate.html Suggested annual donation
> $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/healey.nut@gmail.com
>
--
Sent from my mobile device
_______________________________________________
Healeys@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/healeys/josef.eckert@t-systems.com
_______________________________________________
Healeys@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
|