Ah, but now we know where to find you!
Charlie wrote:
> There have been some questions asked on the list that I wondered about in
> the past and I suppose they may have got replies off the list. I thought I
> would watch for the answer or help and maybe read and learn something. So I
> have tried to Cc: the list for perhaps someone else may be interested in the
> subject. Sure there are plenty of posts that bore me and others when that
> don't have that certain problem at the present time. I suppose my last post
> of address was not necessary. I wasn't thinking. Sorry.
> -----Original Message-----
> From: stu.jo@ibm.net <stu.jo@ibm.net>
> To: Charlie <c2h60_@email.msn.com>
> Date: Friday, November 13, 1998 3:52 PM
> Subject: Re: Roll Pin
>
> >Charlie wrote:
> >>
> >> I was so excited I forgot you may need my address. 42963 Southeast 170th
> >> Court, North Bend WA 98045-9643. I'll send you a check for a couple a
> >> bucks if you give me your address. Thanks again.
> >> -----Original Message-----
> >> From: Gambony, Jim <jim.gambony@eds.com>
> >> To: 'Charles Ackerman' <C2H60_@email.msn.com>
> >> Date: Thursday, November 12, 1998 9:31 PM
> >> Subject: RE: Roll Pin
> >>
> >> >Charles,
> >> >
> >> >Good news and bad news.
> >> >
> >> >Good news: I picked up the pin for you today
> >> >Bad news: it'll cost you $.35 ($.03 for the pin... and $.32 for postage
> >> :-)
> >> >
> >> >That is if you still need it?
> >> >
> >> >Jim
> >> >
> >> >> -----Original Message-----
> >> >> From: Charles Ackerman [SMTP:C2H60_@email.msn.com]
> >> >> Sent: Thursday, October 22, 1998 7:17 PM
> >> >> To: Gambony, Jim
> >> >> Subject: Re: Roll Pin
> >> >>
> >> >> Hi Jim,
> >> >>
> >> >> 1/8 X 1-7/8
> >> >>
> >> >> CC51493LO
> >> >> -----Original Message-----
> >> >> From: Gambony, Jim <jim.gambony@eds.com>
> >> >> To: 'Charles Ackerman' <C2H60_@email.msn.com>
> >> >> Date: Thursday, October 22, 1998 1:18 PM
> >> >> Subject: RE: Roll Pin
> >> >>
> >> >>
> >> >> >Charles,
> >> >> >
> >> >> >Do you know the dimensions for the pin (diameter and length)?
> >> >> >
> >> >> >I found the local industrial supply house could supply some of the
> "odd"
> >> >> >sizes pretty well.
> >> >> >
> >> >> >Jim
> >> >> >
> >> >> >> -----Original Message-----
> >> >> >> From: Charles Ackerman [SMTP:C2H60_@email.msn.com]
> >> >> >> Sent: Thursday, October 22, 1998 2:35 PM
> >> >> >> To: triumphs_list
> >> >> >> Subject: Roll Pin
> >> >> >>
> >> >> >>
> >> >> >> Howdy folks,
> >> >> >> If anyone out there has the long roll pin for the gas door I will
> buy
> >> >> it.
> >> >> >> Seems all the roll pins at NAPA etc. are to short. Thanks
> >> >> >> CC51493LO
> >> >> >>
> >> >> >>
> >> >>
> >> >>
> >Charlie, don't flame me, but I wonder why you copied the list on a
> >personal message. Just more stuff to wade thru!Stu
--
Michael Ferguson
Vernon CT
|