I think the original name was Pem nut, but there are now lots of
manufactures. Drill a hole and light press fit the pem nut on the back
side. But make sure they are pressed, otherwise you might as well use a
regular nut.
Not sure if this will help your situation, but there are also nuts that have
lock washers attached. These work really well if you can't get wrench
access and don't have the tool to press fit a pem nut. Also really good
against vibration. I have some 10-32 cad plated nuts of this verity if you
need some.
Clif
1974 Jensen Healey
--------------------------------------------------
From: "Scott Irwin" <riprock99@comcast.net>
Sent: Wednesday, May 12, 2010 5:36 PM
To: "North Bay British Car Club" <nobbc@autox.team.net>
Subject: Re: [Nobbc] Speaking of hydraulics.
> They are called nutserts where I'm from.
>
> Scott
>
> --------------------------------------------------
> From: "Bill Crowe" <crowe99@yahoo.com>
> Sent: Wednesday, May 12, 2010 3:46 PM
> To: "North Bay British Car Club" <nobbc@autox.team.net>
> Subject: Re: [Nobbc] Speaking of hydraulics.
>
>> maybe Rivnuts??? Aircraft Spruce carries them...
>>
>> Bill
>>
>> --- On Wed, 5/12/10, sirplb@aol.com <sirplb@aol.com> wrote:
>>
>> From: sirplb@aol.com <sirplb@aol.com>
>> Subject: Re: [Nobbc] Speaking of hydraulics.
>> To: nobbc@autox.team.net
>> Date: Wednesday, May 12, 2010, 3:25 PM
>>
>> Hi Deano,
>>
>> Some years ago (25-30) there were these nuts that could be installed with
>> a
>> pop-rivet type of gun in thin metal. If I remember correctly, they needed
>> a
>> hole just a little larger than the actual nut. (of course the brand name
>> escapes me) Seemed to work fine at the time?!?
>>
>> Cheers,
>>
>> Pat
>>
>> 74 JH 14858
>>
>>
>>
>>
>>
>>
>> -----Original Message-----
>> From: Paige, Dean <DPaige@srcity.org>
>> To: 'North Bay British Car Club' <nobbc@autox.team.net>
>> Sent: Fri, May 7, 2010 9:54 am
>> Subject: [Nobbc] Speaking of hydraulics.
>>
>>
>> It looks like I may well get the Herman van den Akker Toyota 5 speed
>> tranny
>> onversion into the TR-6 this weekend. This after having to ship the
>> tranny
>> ack to southern Cal after UPS dropped the damn thing. In the mean time I
>> leaned up the interior, put a new coat of paint on the floor pan etc etc.
>> Have one small but big issue. The captive nut on the floor pan on the
>> right
>> ront of the drivers side seat gave up the ghost. The placement couldn't
>> be
>> orse. The hole in the floor pan is directly above the frame member there.
>> How
>> n the hell does one deal with this. Barely enough room to get even a
>> screw
>> river in the space. I thought of looking for something similar to metal
>> xpanding molly fasteners used in hanging heavy objects on drywall.
>> Haven't
>> ooked yet to see if there is one available that will stand up to the
>> stresses
>> n the seat. Any advice is welcome.
>> Deano
>> ______________________________________________
>> obbc mailing list
>> obbc@autox.team.net
>> ttp://autox.team.net/mailman/listinfo/nobbc
>> _______________________________________________
>> Nobbc mailing list
>> Nobbc@autox.team.net
>> http://autox.team.net/mailman/listinfo/nobbc
>> _______________________________________________
>> Nobbc mailing list
>> Nobbc@autox.team.net
>> http://autox.team.net/mailman/listinfo/nobbc
>
>
>
>>
>> No virus found in this incoming message.
>> Checked by AVG - www.avg.com
>> Version: 9.0.819 / Virus Database: 271.1.1/2870 - Release Date: 05/12/10
>> 11:26:00
> _______________________________________________
> Nobbc mailing list
> Nobbc@autox.team.net
> http://autox.team.net/mailman/listinfo/nobbc
_______________________________________________
Nobbc mailing list
Nobbc@autox.team.net
http://autox.team.net/mailman/listinfo/nobbc
|