Isn't this an exposed pin hinge like the TR3/4? Can you drill the pin
out and replace it with a cap screw and nylock?
On May 7, 2008, at 11:59 AM, Don Carter wrote:
> I share your frustration. This goes much better with a friend's
> help. In
> fact, without risk of scratching it is real scary. So wait for a
> friend and
> instruct him something like this:
>
> 1. Place at least two of the hood mounting bolts along the front
> fender
> mounting channel near the front of the engine bay by the hinges.
> Also have
> 1/2 inch wrenches handy and within reach of this same area.
> 2. You and a FRIEND pick up the hood holding each of its sides. (If
> you
> don't have a friend, find one. If you can't find one, then sell your
> Triumph without a hood installed.)
> 3. You take the passenger side, especially if your right handed.
> Hoist the
> hood onto each of your inside (the engine side) shoulders, whilst, (a
> British word), facing toward the front of the car.
> 4. Tilt the hood so that the hinges mate as close as possible with
> the hood
> mounting holes and install somewhat loosely two of the bolts through
> the
> passenger side hinge holes.
> 5. Then go over and relieve your friend who is patiently holding his
> driver's side up and who has helped by gently moving the hood whilst
> you
> bolted the passenger side.
> 6. Install two bolts on the driver's side with a bit more tightness
> and
> gently lower the hood and adjust by hand bumping the edges to
> align. Raise
> and tighten until adjustments and alignment is made and finish other
> bolt
> installations.
>
> The floating captured threaded plates are of course the problem, but
> this
> method has worked for me for many installations. Praying for more
> patience
> might also help before you start.
>
> Don Carter, AIA
>
>
>
> Carter Design Associates
> 6213 Skyline Dr., Suite 100
> Houston, Texas 77057
> (713) 529-2288 Telephone
> (713) 789-2330 Fax
> don@carterdesignassociates.com
>
>
> -----Original Message-----
> From: fot-bounces+don=carterdesignassociates.com@autox.team.net
> [mailto:fot-bounces+don=carterdesignassociates.com@autox.team.net]
> On Behalf
> Of Chuck Arnold
> Sent: Wednesday, May 07, 2008 12:16 PM
> To: Friends; Triumph
> Subject: [Fot] Replacing TR6 hood
>
>
> Looking to see what tricks people use to re-install the hood after
> engine
> replacement when done as a one person job. I have done it several
> times,
> probably try different techniques each time, and get frustrated with
> all of
> them.
>
> --
> Chuck Arnold
> Fot mailing list
> Fot@autox.team.net
> http://autox.team.net/mailman/listinfo/fot
>
> You are subscribed as don@carterdesignassociates.com
> _______________________________________________
> http://www.team.net/donate.html
>
> Fot mailing list
> Fot@autox.team.net
> http://autox.team.net/mailman/listinfo/fot
>
> You are subscribed as billb@bnj.com
Bill Babcock
Babcock & Jenkins
Billb@bnj.com
503.936.7660
www.bnj.com
_______________________________________________
http://www.team.net/donate.html
Fot mailing list
Fot@autox.team.net
http://autox.team.net/mailman/listinfo/fot
|