datsun-roadsters
[Top] [All Lists]

Re: brake master 2000

To: <datsun-roadsters@autox.team.net>
Subject: Re: brake master 2000
From: "Richard Wright" <duntov1@attbi.com>
Date: Mon, 24 Dec 2001 08:37:48 -0600
The treads for the brakelines were the same as the 2000, they were all
3/8sae fine thread.
RichW
----- Original Message -----
From: "datsunmike" <datsunmike@nyc.rr.com>
To: "Richard Wright" <duntov1@attbi.com>; <datsun-roadsters@autox.team.net>
Sent: Monday, December 24, 2001 8:31 AM
Subject: Re: brake master 2000


> Rich,
>
> That should be a metric master. You'll need adapters to get the brake
lines
> to fit correctly.
>
> Mike
> ----- Original Message -----
> From: "Richard Wright" <duntov1@attbi.com>
> To: <datsun-roadsters@autox.team.net>
> Sent: Monday, December 24, 2001 5:30 AM
> Subject: Re: brake master 2000
>
>
> > The reason I asked about the brake master is because I found a near
direct
> > bolt in master cylinder for $40!
> > I just installed a 1972 620 Datsun truck brake master from O'Reiley's
auto
> > parts, using the original 2000 reservoirs. The bore is 3/4, as cast into
> > both the masters on the side. The brake lines point down, but with a
> little
> > different spacing.
> >
> > You just half to start the brake lines before you install the master the
> > rest of the way!
> >
> > Rich W
> > Dallas
> > ----- Original Message -----
> > From: "Adam Bradley" <ambradley@yahoo.com>
> > To: "Richard Wright" <duntov1@attbi.com>
> > Sent: Sunday, December 23, 2001 8:57 PM
> > Subject: Re: brake master 2000
> >
> >
> > > I don't know the bore, but 68-70 1600 and 2000 use the same master
> > > cylinder.
> > >
> > > The clutch and brake pedal should sit at the same height.  Look under
> > > your dash and see if one of the pedal stops is bent back.  You may
have
> > > an aftermarket clutch master cylinder that has a threaded rod and
> > > clevis.  It may be adjusted too high, and the pedal stop may be bent
> > > back to stop it from constantly depressing the clutch pedal (partially
> > > engaged clutch).
> > >
> > > --- Richard Wright <duntov1@attbi.com> wrote:
> > > > Is the brake master bore 3/4" on a 2000?
> > > > Does the brake pedal sit low like the gas pedal, or up higher up
like
> > > > the
> > > > clutch?
> > > > Rich W
> > > > Dallas
> > > >
> > > > ///  datsun-roadsters@autox.team.net mailing list
> > > > ///  Send admin requests to majordomo@autox.team.net  or go to
> > > > ///  http://www.team.net/cgi-bin/majorcool
> > > > ///  Send list postings to datsun-roadsters@autox.team.net
> > > >
> > >
> > >
> > > =====
> > > Adam
> > > '70 1600 SPL311-28181
> > > http://www.picturetrail.com/abend
> > > Send your FREE holiday greetings online!
> > > http://greetings.yahoo.com
> >
> > ///  datsun-roadsters@autox.team.net mailing list
> > ///  Send admin requests to majordomo@autox.team.net  or go to
> > ///  http://www.team.net/cgi-bin/majorcool
> > ///  Send list postings to datsun-roadsters@autox.team.net

///  datsun-roadsters@autox.team.net mailing list


<Prev in Thread] Current Thread [Next in Thread>