shop-talk (date)
August 27, 1999
- Re: Torque Wrench, Phil Ethier, 22:25
- Re: Torque Wrench, Phil Ethier, 22:21
- Re: Torque Wrench, Aaron Bergman, 17:38
- Re: Dealing with A&I Supply?, Roland Wilhelmy, 13:00
- Re: Dealing with A&I Supply?, Chris Heerschap, 11:49
- Re: Dealing with A&I Supply?, Susan and John Roper, 11:21
- Re: Torque Wrench, Steve Budde, 11:06
- Dealing with A&I Supply?, Chris Heerschap, 09:07
- Re: Torque Wrench, Susan and John Roper, 09:02
- Re: Torque Wrench, Tim Mullen, 07:52
August 26, 1999
- Re: Torque Wrench, Phil Ethier, 23:15
- Re: Torque Wrench, LBC286, 18:12
- [Fwd: Re: Correction Salt-x], Ed Van Scoy, 15:30
- Torque Wrench, jvanho01, 15:20
- RE: Metric Conversion, Randall Young, 12:17
- Metric Conversion, David Bellingham, 03:32
August 24, 1999
- Re: Metric Bolt Specs, Chris Kantarjiev, 20:20
- Metric Bolt Specs, nogera, 18:52
- Re: Abrasive Blaster, nogera, 18:48
- Re: Abrasive Blaster, John T. Blair, 17:13
- Re: transmission oil, Tom Shirley, 16:33
- Re: Abrasive Blaster, Roland Wilhelmy, 09:40
- Re: transmission oil, LSAPEX, 08:48
- Re: Abrasive Blaster, Derek Harling, 08:07
- RE: Abrasive Blaster, Barry E. Nielsen, 07:27
- Re: Abrasive Blaster, R. John Lye, 06:57
- transmission oil, JRMaster, 06:44
- Abrasive Blaster, Gil Fuqua, 06:29
- RE: Cryogenic :-) Dent Repair?, Gerald J. Brazil, 05:48
August 20, 1999
- Re: Dewalt, Phil Ethier, 22:31
- Re: Dewalt, nogera, 20:31
- Re: Dewalt, Richard Beels, 16:59
- self-aplied CPR a hoax?, Rex Burkheimer, 07:19
- Re: Dewalt, Steve Hammatt, 06:33
- Re: Dewalt, Keith R. Stewart, 05:47
August 19, 1999
- Re: Dewalt, Steve Budde, 22:40
- Re: Dewalt, David Cole, 22:04
- RE: self applied CPR, Randall Young, 21:52
- CPR...., Mordy Dunst, 21:47
- Dewalt, Aaron Bergman, 19:45
- Fw: self applied CPR, Rex Burkheimer, 13:20
August 16, 1999
- Re: general wrench question, Phil Ethier, 23:40
- Re: 8 point sockets....was general wrench question, Keith R. Stewart, 19:36
- Re: 8 point sockets....was general wrench question, Derek Harling, 13:44
- RE: 8 point sockets....was general wrench question, jniolon, 12:47
- RE: general wrench question, Randall Young, 10:58
- Re: general wrench question, Doug Mitchell, 06:03
August 13, 1999
- Re: general wrench question, R. John Lye, 13:50
- Re: general wrench question, Chris Kantarjiev, 11:46
- RE: general wrench question, Mark Miller, 10:40
- Re: general wrench question, Douglas Shook, 10:35
- Re: general wrench question, R. John Lye, 08:55
- Re: general wrench question, Chris Heerschap, 08:33
- Re: general wrench question, Tw Cook, 08:09
- Re: general wrench question, jniolon, 07:45
- Re: general wrench question, Doug Mitchell, 07:26
August 11, 1999
- Re: Flowbench & Engine Dyno, Michael D. Porter, 20:01
- Re: Arrgh ! revisited, Ralph Cordell, 18:00
- RE: HVAC Sizing Books, John Miller, 17:30
- RE: HVAC Sizing Books, Randall Young, 12:26
- Flowbench & Engine Dyno, Chris Crisenbery, 12:05
- Re: Arrgh ! revisited, Mike Rambour, 12:01
- HVAC Sizing Books, John Miller, 10:31
- Arrgh ! revisited, Malaboge, 10:27
August 07, 1999
- welding an exhaust leak, Lin, Gary, 21:59
- Re:, Lawrence Zink, 12:29
- more on craftsman compressors, was: RE: AirComp Qs, Scott Hall, 11:18
- Spot welds with a MIG, nogera, 09:36
August 06, 1999
- Re:, Douglas Shook, 14:55
- Re: AirComp Qs - getting the water out!, cw26, 14:52
- RE:, Brian Borgstede, 13:33
- RE:, Gerald Brazil, 13:18
- Re:, LSAPEX, 13:16
- RE: AirComp Qs, Borgstede, Brian R., 12:40
- Re:, Roger Gibbs, 11:38
August 05, 1999
- RE: AirComp Qs, Scott Hall, 21:06
- Re: Arrgh !, John T. Blair, 17:04
- Re: Arrgh !, mdunst, 16:49
- Re: more compressors, Douglas Shook, 15:14
- Arrgh !, Malaboge, 15:01
- Re: AirComp Qs, Douglas Shook, 14:48
- more compressors, Rex Burkheimer, 14:07
- Re: AirComp Qs, Rex Burkheimer, 12:44
- Re: AirComp Qs, Douglas Shook, 11:27
- RE: Good Workbench, Mark Miller, 10:18
August 02, 1999
- Re: Good Workbench, Chris Kantarjiev, 21:44
- Re: Good Workbench, Steve Budde, 21:32
- Re: Good Workbench, Chris Kantarjiev, 17:19
- RE: LBCs, Randall Young, 17:16
- LBCs, Rex Burkheimer, 15:48
- Safety Wire Article, Steve Budde, 13:47