Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Clutch\s+Hydraulics\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Clutch\s+Hydraulics\s*$/: 8 ]

Total 8 documents matching your query.

1. CLUTCH HYDRAULICS (score: 1): Author: Unknown; Date: Sun, 11 Apr 2004 17:28:24 EDT; happy easter everyone I was planning to rebuild the clutch hydraulics on my 71 tr 6, but rebuilding may not be practicul.The mast piston has some movement but the exterior of it has corroded so i thi; /html/triumphs/2004-04/msg00343.html (7,002 bytes)
2. Re: CLUTCH HYDRAULICS (score: 1): Author: Unknown; Date: Thu, 15 Apr 2004 17:25:07 EDT; and has any found a local supplie for u joints i have a web page that list possible replacemen t joints but was wondering if some one bought them a napa or some where and knew a part number TIA jason; /html/triumphs/2004-04/msg00487.html (6,528 bytes)
3. Clutch Hydraulics (score: 1): Author: Unknown; Date: Sun, 24 Mar 2002 21:16:16 -0500; On a friend's '75 TR6, replaced the clutch a few weeks ago, got drive train re-assembled, etc. During test drive, the clutch wouldn't push the arm on the clutch shaft very far. Rebuilt slave cyl. wi; /html/triumphs/2002-03/msg01268.html (6,911 bytes)
4. Re: Clutch Hydraulics (score: 1): Author: Unknown; Date: Sun, 24 Mar 2002 21:33:51 -0500; Could there still be air in the hydraulics? Two possible causes are the slave was reinstalled upside down (the bleed valve needs to be on top) or the pedal was worked too gently during bleeding (you; /html/triumphs/2002-03/msg01272.html (7,791 bytes)
5. Clutch Hydraulics (score: 1): Author: Unknown; Date: Sun, 24 Mar 2002 21:32:55 -0500; Message text written by INTERNET:stantr6@bellsouth.net train re-assembled, etc. During test drive, the clutch wouldn't push the arm on the clutch shaft very far. Rebuilt slave cyl. with kit from V.B.; /html/triumphs/2002-03/msg01273.html (7,627 bytes)
6. Clutch Hydraulics (score: 1): Author: Unknown; Date: Mon, 25 Mar 2002 08:06:50 -0800; <Clutch is still soft, more ineffective now after the rebuild and fluid When you bleed the slave cylinder, besides being sure the bleed screw is on the top, hold the pushrod in when the clutch pedal; /html/triumphs/2002-03/msg01287.html (7,204 bytes)
7. Clutch hydraulics (score: 1): Author: Unknown; Date: Fri, 19 Dec 1997 16:06:52 -0800; My clutch hydraulics have gone again! The seals are wearing rapidly due to a scored bore so I'll have to replace the master cylinder. Has anyone replaced the entire system with a cable like modern ca; /html/triumphs/1997-12/msg00983.html (6,345 bytes)
8. Re: Clutch hydraulics (score: 1): Author: Unknown; Date: Fri, 19 Dec 1997 11:23:52 +0500 (EST); Andy, WHY? I've had more bad luck over the years with cables than with hydraulics. I went through three VERY EXPENSIVE cables on a Volvo some years back before I finally determined that the factory (; /html/triumphs/1997-12/msg00987.html (7,389 bytes)

Current List: 1 - 8
Page: [1]