triumphs
[Top] [All Lists]

Re: [TR] Float bowls overflowing

To: Roger Elliott <elliottr@rmi.net>, "triumphs@autox.team.net" <triumphs@autox.team.net>
Subject: Re: [TR] Float bowls overflowing
From: Frank Fisher <yellowtr3@yahoo.com>
Date: Thu, 10 May 2012 10:00:55 -0700 (PDT)
Delivered-to: mharc@autox.team.net
Delivered-to: triumphs@autox.team.net
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=yahoo.com; s=s1024; t=1336669255; bh=jxBFBu7RkYIpfYxqyr7ttg/8zSqwRyiIjRsMdiw8dTw=; h=X-YMail-OSG:Received:X-Mailer:References:Message-ID:Date:From:Reply-To:Subject:To:In-Reply-To:MIME-Version:Content-Type; b=IbbOfd6eau4KngWR80LiqTO11qoPMsMrYOdCT6BkXHxUS4z5YDOmairZwCO9roSb31UpO9lM7QdrvdiH8PEU+MFf7Z61QHjA0xOvre9JxkRq3kdQ6ckLv1YeJSbO+FvT+sOidY+22rBbJ97EjkM+ZfXTReIbwKY4H2mB977MYhM= s=s1024; d=yahoo.com; h=X-YMail-OSG:Received:X-Mailer:References:Message-ID:Date:From:Reply-To:Subject:To:In-Reply-To:MIME-Version:Content-Type; b=YsrYqB3+OhcylINJ00yzWoU2Yax1p6SfFtliUhj/qPmuPycgqKnLZlOG7N7QfjweK1Q3xM0Uw1DD3/P14+dHTDhY9LKXACKo/jBcFgZXOwzlMKfxWG+dq4vygpvCtIgVxvBe8C0g1Tbu/k6vm+JLC4AAmvMjkcOctf/CHSLW4+s=;
In-reply-to: <24446925.1336661794983.JavaMail.root@elwamui-rubis.atl.sa.earthlink.net>
List-archive: <http://autox.team.net/pipermail/triumphs>
List-help: <mailto:triumphs-request@autox.team.net?subject=help>
List-id: Triumph Sports car discussion <triumphs.autox.team.net>
List-post: <mailto:triumphs@autox.team.net>
List-subscribe: <http://autox.team.net/mailman/listinfo/triumphs>, <mailto:triumphs-request@autox.team.net?subject=subscribe>
List-unsubscribe: <http://autox.team.net/mailman/options/triumphs>, <mailto:triumphs-request@autox.team.net?subject=unsubscribe>
References: <24446925.1336661794983.JavaMail.root@elwamui-rubis.atl.sa.earthlink.net>
Reply-to: Frank Fisher <yellowtr3@yahoo.com>
Sender: triumphs-bounces@autox.team.net
Roger
there is an adjustment to be made that sets the height the float bowl
comes to and closes the needle valve.
on my TR3 there is a 2 finger hinge like
device that is curved.
you set the height by checking it with a specific drill
diameter.
i cant recall the exact diameter but im sure some one will tell us.
check your workshop manual, it will have pictures.
Frank

From: Roger Elliott
<elliottr@rmi.net>
To: triumphs@autox.team.net 
Sent: Thursday, May 10, 2012
7:56 AM
Subject: [TR] Float bowls overflowing

Hi,

I have a 1980 Spitfire
with dual SU HS4 carbs.  I noticed while trying to get to run correctly that
the front fuel bowl had gas coming out the top vent hole.  

Figuring that it
was the needle valve sticking, I replaced the needle valves and floats in both
fuel bowls.  

The front bowl (second in fuel line) contined to overflow.  I
thought that there may be a crack or something in the lid, so I dug out
different lid, put the new bowls and valves in the lids, made sure the float
adjustment is correct. 

These lids have vent tubes, which I have connected
with fuel hose - above the carbs.

Well, gas is coming out of the vent hose
connected to the vent tubes  - not sure which carb is overflowing at this
point as I did not think to disconnect them until after I stopped working on
them for the evening. 

The fuel line now has a T-connector to get gas to both
carbs.  Previously, the rear carb had a fuel pass through.

I have a
mechanical fuel pump, not original.  But one sold by one of the big vendors -
don't remember which now.

Can the mechanical pumps put out too much
pressure?  The pump has been on for a few years and it has run correctly in
the past.

Assuming I haven't botched installing the needle valves and floats,
is there anything besides excess fuel pressure that would cause the bowls to
overflow?

Thanks,
Roger Elliott
1980 Spitfire

** triumphs@autox.team.net **
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/triumphs/yellowtr3@yahoo.com

** triumphs@autox.team.net **

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage: 
http://autox.team.net/mailman/options/triumphs/mharc@autox.team.net

<Prev in Thread] Current Thread [Next in Thread>