I haven't seen sanding/buffing the surface mentioned either.
Putting a "shine" on the metal you want to solder has always worked
better for me than not. Solder likes shiny metal and flux. Works
similar to welding...if you don't grind it you're not going to get a
good weld. Try a tiny round file in the bullet connectors to rough
the surface or anything to get the surface layer broken. Scratch it
with a pin?
Bud Rolofson
71TR6 CC57365 (Good 6)
66TR4A CTC57806 (The Wreck-Almost parts)
66TR4A CTC57529 (The Project)
71F-250 Camper Special (Triumph Support Vehicle)
Z-50A Hardly Davidson 1977 Honda Mini-Trail Bike (Triumph Pit Bike)
levilevi at comcast.net
On Mar 4, 2012, at 12:48 PM, fogbro1 at comcast.net wrote:
> No one's mentioned "tinning" the wire. Doesn't anyone "tin" the wire
> anymore?
>
>
>
> I dip the wire in flux, "tin" it, then feed it into the hot bullet,
> having
> previously melted solder into the bullet. If off the car, the bullet
> can be
> positioned in a vice and the wire fed into it. If on the car, the
> bullet can
> be held in a forcepts to minimize heat loss and fed onto the wire .
>
>
>
> Ed Woods
>
>
>
> ----- Original Message -----
>
>
> From: "Lee&John Howard" <leejohn7 at gmail.com>
> To: Dave1massey at cs.com
> Cc: triumphs at autox.team.net
> Sent: Sunday, March 4, 2012 12:20:56 PM
> Subject: Re: [TR] soldering
>
> I'm with you on that, Dave. I usually try to position a wooden
> carpentry
> clamp so that it can gently hold the wire while I apply the iron to
> the
> bullet.
> John Howard
>
>
> On Sun, Mar 4, 2012 at 7:48 AM, <Dave1massey at cs.com> wrote:
>
>> In a message dated 3/3/2012 10:00:42 PM Central Standard Time,
>> nafzigerg at yahoo.com writes:
>>> Do I need a larger soldering iron or do I need
>>> different solder? B Is there a solder specifically for electrical
>>> connections
>>> in cars that has a lower melting point?
>>>
>>
>> You have received a couple of well informed replies already but let
>> me add
>> my technique to the list.
>>
>> The secret to soldering is to get the parts hot enough to melt the
>> solder.
>> I apply a small ammount of solder to the tip of the soldering gun/
>> iron as
>> this will greatly improve heat transfer. B Then I heat the bullet
>> since this
>> is the largets mass. B I then apply the solder to the bullet. B
>> When it gets
>> hot enough the solder will begin to melt and I feed the solder in
>> to make
>> the
>> joint. B With that ammount of heat and the bullet hot enough the
>> wire will
>> quickly heat up enough to take up the solder and the joint will be
>> a solid
>> one.
>>
>> I just made a dozen or so of these joints last weekend on my TR3
>> and the
>> biggest problem I had was caffine related. B Trying to hold the
>> soldering
>> gun
>> sdeady for the 30 seconds or so on a bullet ballanced precariously
>> on the
>> end
>> of a small, wavering wire while trying to apply solder with the other
>> required much concentration for this old man.
>>
>> It ain't easy and I have quite a bit of experience in electrical
>> soldering.
>>
>> Dave
>>
>> ** triumphs at autox.team.net **
>>
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/triumphs/leejohn7 at gmail.com
>
> ** triumphs at autox.team.net **
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/triumphs/fogbro1 at comcast.net
>
> ** triumphs at autox.team.net **
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage: http://autox.team.net/mailman/options/triumphs/levilevi
> at comcast.net
|