triumphs
[Top] [All Lists]

[TR] [6pack] TR6 Inside Door Handle Installation

Subject: [TR] [6pack] TR6 Inside Door Handle Installation
From: 75tr6 at tr6.danielsonfamily.org (Bob Danielson)
Date: Mon, 17 Jan 2011 14:29:00 -0500
References: <78800.69d9f900.3a65e3d3@aol.com> <!&!AAAAAAAAAAAYAAAAAAAAAJL2xS8Qce5OmzH6VzgCDbfCgAAAEAAAAIZ/0lZBZ/dDhKbHRlfpuPsBAAAAAA==@optonline.net>
I've never done it with the springs but here two techniques that work well.

1. Toward the end of this article are a few pictures 
http://tr6.danielsonfamily.org/WindowChannel.htm

2. The other involves a welding rod or thick wire hanger. Slide it through 
the handle to determine the length of a pin needed and score the rod/hanger 
with a wire cutter. Mount the handle to the door, slide the rod/wire in and 
wiggle it back and forth until it snaps. Both fixes are very easy to 
do.............at least without the spring.

Bob


Bob Danielson
http://tr6.danielsonfamily.org
1975 TR6 with:
Throttle Body Injection
Toyota 5 Speed
Nissan Diff & CVJs

-----Original Message----- 
From: Bob
Sent: Monday, January 17, 2011 1:52 PM
To: TR250Driver at aol.com ; triumphs at autox.team.net
Cc: 6pack at autox.team.net
Subject: Re: [TR] [6pack] TR6 Inside Door Handle Installation

Hello Darrell,
I used a cut down piece of a finishing nail that is a tiny bit narrower than
that barrel instead.
It went in easy and spring pressure keeps a hold on it, been working just
fine.
You might give it a try.
Regards,
Bob

-----Original Message-----
From: 6pack-bounces at autox.team.net [mailto:6pack-bounces at autox.team.net] 
On
Behalf Of TR250Driver at aol.com
Sent: Monday, January 17, 2011 1:26 PM
To: triumphs at autox.team.net
Cc: 6pack at autox.team.net
Subject: [6pack] TR6 Inside Door Handle Installation

Hey Guys,
I have about an hour in it now with Beverly helping.  No  success, we just
gave up.  Trying to get that little barrel into both  holes with the springs
behind the door is impossible!!!!!  I have done  this before but I think I
always coped out and took the springs out.  Then  it is just very difficult.

I have the door glass replaced, the panel back  on and all I need is the
handles back on.

I hear there is a special tool for this.  Anyone know where I can buy  one?
Any tips on how to make this job possible?  I tried using needle  nose vise
grips & needle nose pliers.

Thanks,
Darrell
_______________________________________________

6pack at autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe/Manage:
http://autox.team.net/mailman/options/6pack/rpeglow at optonline.net

_______________________________________________
Triumphs at autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation  $11.47
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Manage your account: 
http://autox.team.net/mailman/options/triumphs/75tr6 at tr6.danielsonfamily.org 


<Prev in Thread] Current Thread [Next in Thread>