triumphs
[Top] [All Lists]

Re: OD wiring

To: naffy@netins.net, triumphs@autox.team.net
Subject: Re: OD wiring
From: DANMAS@aol.com
Date: Sat, 6 Feb 1999 20:13:37 EST
In a message dated 2/6/99 2:50:04 PM Eastern Standard Time, naffy@netins.net
writes:

> I'm getting there!  Have all the overdrive wiring loom hooked up as I think
>  it should be with help from the list.  Hooked up new solenoid and doesn't
>  seem to work.  have fire after the switch but no fire at the yellow and
>  purple wire that goes to the solenoid. no fire with switch off or on.  Do
>  have fire at the solid yellow wire that goes to the cut out switches.
>  Anything wrong?

Gary,

I am assuming you are using a relay for your overdrive circuit. If so, check
your wiring as follows:

On the relay, you should have - 

one brown wire on the C1 terminal,
one white wire on the W1 terminal,
one yellow/green wire on the W2 terminal, and
one yellow/purple wire on the C2 terminal. 

(Note: the C1 and C2 terminals are interchangable, as are the W1 and W2, so
you could have the brown wire on the C2, with the y/p wire on the C1.
Likewise, the y/g wire could be on W1, with the white wire on W2. The relay
will work just fine either way)

If you have wired it correctly, you will get "fire" at the yellow wire to the
inhibit switches, as you stated. I put "fire" in parenthesis because it's not
really "fire" as we normally think of it. It's 12 volts, but the yellow wire
is intended to be grounded, so the relay coil is between the battery and the
yellow wire. The yellow wire does not provide "power" to any load. To verify
this, you can use a 12 volt light bulb to test it. To do this, connect one
side of the bulb to the yellow wire and the other side to ground. If the bulb
lights, you have a wiring error.

Before you do that test, though, check the wiring at your relay to verify that
it is wired as above, and then test your wiring as follows below. 

a) With the key on, verify that you have 12 volts on the white wire. If not,
look for a break or a bad connection in the white wire from the ignition key
to the relay.

b) Verify that you have 12 volts on the brown wire with the key on OR off. If
not, look for a problem in the brown wire circuit - broken wire or bad
connection.

c) Put your meter on the yellow/purple wire, and run a jumper from the relay
terminal with the yellow/green wire to ground. With the key on, and this
terminal grounded, you should get 12 volts at the yellow/purple wire. If you
pass tests a) and b), but fail c), then your relay is bad or the connections
to it are bad - ie, corroded terminals or such.

d) If you pass tests a), b), and c), but still get no power to your solenoid
(with the ground jumper still in place), then you have a break or bad
connection in the yellow/purple wire to the solenoid from the relay.

e) If you passed all of the above tests, but the solenoid still doesn't get
power when you are actually operating it, then your inhibit switches are
either bad or have a faulty ground, or there is a fault in the wiring from the
relay to the manual switch to the inhibit switches. At this point, you will
need to do the light bulb test mentioned above, just to be on the safe side.
After you have verified that the bulb does not light (or VERY dimly at best,
if it is a low wattage bulb), connect the yellow wire (at the OD unit) to
ground and try the circuit again. BE WARNED - This last test defeats the
function of the inhibit switch, so you will need to be SURE that you don't
operate the OD unit in a gear that it's not intended to be operated in, most
specifically, NOT in reverse. If the solenoid now works, your inhibit switches
are the problem. If not, then the switch wiring is the problem - either a
broken wire or one or more bad connections in the yellow/green wires, the
yellow wire, or the short black wire to the manual switch. At this point, I
would suspect the inhibit switches, as you have voltage on the yellow wire.

When you have finished these tests, you will have found the problem, I think!
I hope I haven't left anything out, but if I did, let me know and I'll correct
it.

If you have any questions, let me know.

Dan Masters,
Alcoa, TN

'71 TR6---------3000mile/year driver, fully restored
'71 TR6---------undergoing full restoration and Ford 5.0 V8 insertion - see:
                    http://members.aol.com/danmas/
'74 MGBGT---3000mile/year driver, original condition - slated for a V8 soon
'68 MGBGT---organ donor for the '74

<Prev in Thread] Current Thread [Next in Thread>