--===============5477368136752141510==
boundary=Apple-Mail-1F941502-CAF8-49D1-BC38-3867EAFC6121
Content-Transfer-Encoding: 7bit
--Apple-Mail-1F941502-CAF8-49D1-BC38-3867EAFC6121
charset=utf-8
Content-Transfer-Encoding: quoted-printable
Russ
Double check that you didn=E2=80=99t lose a trunion. I had one fall out and h=
ad a heck of a time shifting after my build. =20
Paul
Sent from my iPad
> On Apr 19, 2019, at 3:02 PM, Ron Fraser via Tigers <tigers@autox.team.net>=
wrote:
>=20
> Russ
> I believe I=E2=80=99ve been there and sometimes still happe=
ns.
> The linkage is stuck in reverse gear position. If you put it back into r=
everse and carefully pull it out of reverse it should be OK. I found that w=
orked after getting under the Tiger a couple times to get it in a forward ge=
ar which is no fun at all.
> =20
> I believe this problem is all in the shifter mechanism.
> =20
> I=E2=80=99m not exactly sure how I reduced this occurrence, it was 20 year=
s ago, but here is a go at it.
> I believe I took the shifter mechanism out =E2=80=93 cleaned it =E2=80=93 i=
nspected it - lubed it and I stretched the spring a little.
> I also replaced the trunnion on the shifter.
> Assemble the shifter =E2=80=93 check and adjust the shifter linkage as req=
uired.
> =20
> That worked for me =E2=80=93 only once in a great while does the shifter h=
ang up now.
> =20
> Hope this helps with your problem
> Ron Fraser
> =20
> From: Tigers <tigers-bounces@autox.team.net> On Behalf Of Russ and Tammy C=
. via Tigers
> Sent: Friday, April 19, 2019 12:42 PM
> To: tigers@autox.team.net
> Subject: [Tigers] top loader 4 speed wide ratio
> =20
> After my recent engine rebuild I am having trouble with the tranny getti=
ng stuck in two gears. Not good. It occurs when trying to go forward after=
putting it in reverse It won't go into any forward gear. Did I perhaps bend=
something getting it back into the tunnel on replacing the motor? I didn't=
do anything to the tranny when out of the car. I did clean it up and repa=
int before re-entry. It was suggested that I cleaned it too good and it ne=
eded to be relubed on the rods and levers. That did seem to help but it sti=
ll gets stuck on occasion and I can release it by putting it back into rever=
se. That is the good news. I had to get under the car and hit the lever bef=
ore to pop it out of gear. The levers all line up where they should be un=
der the shifter. Fluid level is good. Is the fluid correct( valvoline gear=
oil--high performance 80-90w )? Any suggestions would be appreciated. Rus=
s rtscolgan@yahoo.com
> _______________________________________________
>=20
> tigers@autox.team.net
>=20
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/tigers http://autox.team.net/archiv=
e
>=20
> Unsubscribe: http://autox.team.net/mailman/options/tigers/ironbeast@comcas=
t.net
>=20
>=20
--Apple-Mail-1F941502-CAF8-49D1-BC38-3867EAFC6121
charset=utf-8
Content-Transfer-Encoding: quoted-printable
<html><head><meta http-equiv=3D"content-type" content=3D"text/html; charset=3D=
utf-8"></head><body dir=3D"auto">Russ<div>Double check that you didn=E2=80=99=
t lose a trunion. I had one fall out and had a heck of a time shifting after=
my build. </div><div><br></div><div>Paul</div><div><br></div><d=
iv><br></div><div><br></div><div><br></div><div><br></div><div><br></div><di=
v><br><br><div id=3D"AppleMailSignature" dir=3D"ltr">Sent from my iPad</div>=
<div dir=3D"ltr"><br>On Apr 19, 2019, at 3:02 PM, Ron Fraser via Tigers <=
<a href=3D"mailto:tigers@autox.team.net";>tigers@autox.team.net</a>> wrote=
:<br><br></div><blockquote type=3D"cite"><div dir=3D"ltr"><meta http-equiv=3D=
"Content-Type" content=3D"text/html; charset=3Dutf-8"><meta name=3D"Generato=
r" content=3D"Microsoft Word 15 (filtered medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:Helvetica;
panose-1:2 11 6 4 2 2 2 2 2 4;}
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:#0563C1;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:#954F72;
text-decoration:underline;}
p.msonormal0, li.msonormal0, div.msonormal0
{mso-style-name:msonormal;
mso-margin-top-alt:auto;
margin-right:0in;
mso-margin-bottom-alt:auto;
margin-left:0in;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
span.EmailStyle19
{mso-style-type:personal-reply;
font-family:"Calibri",sans-serif;
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-size:10.0pt;}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext=3D"edit" spidmax=3D"1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext=3D"edit">
<o:idmap v:ext=3D"edit" data=3D"1" />
</o:shapelayout></xml><![endif]--><div class=3D"WordSection1"><p class=3D"Ms=
oNormal">Russ<o:p></o:p></p><p class=3D"MsoNormal"> =
I believe I=E2=80=
=99ve been there and sometimes still happens.<o:p></o:p></p><p class=3D"MsoN=
ormal">The linkage is stuck in reverse gear position. If you put=
it back into reverse and carefully pull it out of reverse it should be OK.&=
nbsp; I found that worked after getting under the Tiger a couple times=
to get it in a forward gear which is no fun at all.<o:p></o:p></p><p class=3D=
"MsoNormal"><o:p> </o:p></p><p class=3D"MsoNormal">I believe this probl=
em is all in the shifter mechanism.<o:p></o:p></p><p class=3D"MsoNormal"><o:=
p> </o:p></p><p class=3D"MsoNormal">I=E2=80=99m not exactly sure how I r=
educed this occurrence, it was 20 years ago, but here is a go at it.<o:p></o=
:p></p><p class=3D"MsoNormal">I believe I took the shifter mechanism out =E2=
=80=93 cleaned it =E2=80=93 inspected it - lubed it and I stretched the spri=
ng a little.<o:p></o:p></p><p class=3D"MsoNormal">I also replaced the trunni=
on on the shifter.<o:p></o:p></p><p class=3D"MsoNormal">Assemble the shifter=
=E2=80=93 check and adjust the shifter linkage as required.<o:p></o:p></p><=
p class=3D"MsoNormal"><o:p> </o:p></p><p class=3D"MsoNormal">That worke=
d for me =E2=80=93 only once in a great while does the shifter hang up now.<=
o:p></o:p></p><p class=3D"MsoNormal"><o:p> </o:p></p><p class=3D"MsoNor=
mal">Hope this helps with your problem<o:p></o:p></p><p class=3D"MsoNormal">=
Ron Fraser <o:p></o:p></p><p class=3D"MsoNormal"><o:p> </o:p></p><div><=
div style=3D"border:none;border-top:solid #E1E1E1 1.0pt;padding:3.0pt 0in 0i=
n 0in"><p class=3D"MsoNormal"><b>From:</b> Tigers <<a href=3D"mailto:tige=
rs-bounces@autox.team.net">tigers-bounces@autox.team.net</a>> <b>On Behal=
f Of </b>Russ and Tammy C. via Tigers<br><b>Sent:</b> Friday, April 19, 2019=
12:42 PM<br><b>To:</b> <a href=3D"mailto:tigers@autox.team.net";>tigers@auto=
x.team.net</a><br><b>Subject:</b> [Tigers] top loader 4 speed wide ratio<o:p=
></o:p></p></div></div><p class=3D"MsoNormal"><o:p> </o:p></p><div><div=
><p class=3D"MsoNormal"><span style=3D"font-size:10.0pt;font-family:"He=
lvetica",sans-serif">After my recent engine rebuild I am ha=
ving trouble with the tranny getting stuck in two gears. Not good.&nbs=
p; It occurs when trying to go forward after putting it in reverse It won't g=
o into any forward gear. Did I perhaps bend something getting it back into t=
he tunnel on replacing the motor? I didn't do anything to the tranny&n=
bsp; when out of the car. I did clean it up and repaint before re-entr=
y. It was suggested that I cleaned it too good and it needed to b=
e relubed on the rods and levers. That did seem to help but it still g=
ets stuck on occasion and I can release it by putting it back into reverse.&=
nbsp; That is the good news. I had to get under the car and hit the lever be=
fore to pop it out of gear. The levers all line up where they s=
hould be under the shifter. Fluid level is good. Is the fluid co=
rrect( valvoline gear oil--high performance 80-90w )? Any suggestions w=
ould be appreciated. Russ &n=
bsp; <a href=3D"mailto:rtscolgan@y=
ahoo.com">rtscolgan@yahoo.com</a><o:p></o:p></span></p></div></div></div></d=
iv></blockquote><blockquote type=3D"cite"><div dir=3D"ltr"><span>___________=
____________________________________</span><br><span></span><br><span><a hre=
f=3D"mailto:tigers@autox.team.net";>tigers@autox.team.net</a></span><br><span=
></span><br><span>Donate: <a href=3D"http://www.team.net/donate.html";>http:/=
/www.team.net/donate.html</a></span><br><span>Archive: <a href=3D"http://www=
.team.net/pipermail/tigers">http://www.team.net/pipermail/tigers</a> <a href=
=3D"http://autox.team.net/archive";>http://autox.team.net/archive</a></span><=
br><span></span><br><span>Unsubscribe: <a href=3D"http://autox.team.net/mail=
man/options/tigers/ironbeast@comcast.net">http://autox.team.net/mailman/opti=
ons/tigers/ironbeast@comcast.net</a></span><br><span></span><br><span></span=
><br></div></blockquote></div></body></html>=
--Apple-Mail-1F941502-CAF8-49D1-BC38-3867EAFC6121--
--===============5477368136752141510==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/pipermail/tigers http://autox.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net
--===============5477368136752141510==--
|