I have had the same experience with Randy, actually had the panels made to the
height I needed. A+
> Date: Thu, 27 Aug 2009 21:42:09 +0100
> To: wsamouce@kc.rr.com
> From: jeff@v8tiger.demon.co.uk
> CC: willett581@msn.com; kentb@qualcomm.com; tigers@autox.team.net
> Subject: Re: [Tigers] Tiger Sheet metal
>
> Hi all,
>
>
> Randy Willett also has high quality repair sections sent out from the UK
> which may well be the same as the ones at VB.
>
> I have used the same panels in the UK on several cars very successfully.
>
> randy willett <willett581@msn.com>
>
>
> regards
>
> Jeff
>
>
>
>
>
>
>
>
>
>
>
>
>
> In message <000001ca2737$51d81280$f5883780$@rr.com>, Samouce's
> <wsamouce@kc.rr.com> writes
>>I called Bob recently to inquire about a steel LAT hood. He told me is so
>>many words that I did not have enough money for him to make me one.
>>
>>I recently replaced my front valance with a VB unit. It was a good fit.
>>
>>HTH's
>>Duke
>>B382002037
>>
>>-----Original Message-----
>>From: tigers-bounces@autox.team.net [mailto:tigers-bounces@autox.team.net]
>>On Behalf Of robin02@mindspring.com
>>Sent: Thursday, August 27, 2009 11:43
>>To: Baker,Kent; tigers@autox.team.net
>>Subject: Re: [Tigers] Tiger Sheet metal
>>
>>KEnt, I spoke to Bob Martel about five years ago when he was moving away
>>from the Sunbeam fabrication efforts. HE was selling some things he still
>>had already made but was not doing any more. It was Bob that told me that
>>Victoria British had a good supplier for body panels from ENgland and the
>>fit was good. LArry Paulick later confirmed this and I bought ten body
>>panels for my car; front and back of each wheel well and the outer rocker
>>panels. THe inner rocker panels were fabricated by my body, paint man.
THe
>>fit was good and my car turned out without any evidence of patch panels.
At
>>the time, neither Rick not Curt could fill the order. RObin Young
>>
>>---Original Message-----
>>>From: "Baker, Kent" <kentb@qualcomm.com>
>>>Sent: Aug 26, 2009 1:14 PM
>>>To: "tigers@autox.team.net" <tigers@autox.team.net>
>>>Subject: [Tigers] Tiger Sheet metal
>>>
>>>I am finally getting to the complete restoration of my MK1a, and am
looking
>>>for quality sheet metal replacement parts. Although a Southern California
>>>car, it has rust on the frame exhaust pass through and a few pin holes on
>>the
>>>floorboards immediately above. The shop doing the frame welding contacted
>>>Martell in Ontario, but he is out of the Tiger sheet metal business. I
>>noticed
>>>Classic Sunbeam Auto Parts has the exhaust frame patches listed on its
>>parts
>>>sheet, but have no experience (yet) working with them. Suggestions for
>>>sources? The car is in Reno, Nevada, although I live in San Diego.
>>>
>>>Kent Baker
>>You are subscribed as wsamouce@kc.rr.com
>>
>>Tigers@autox.team.net
>>http://autox.team.net/mailman/listinfo/tigers
>>
>>http://www.team.net/archive
>>_______________________________________________
>>Support Team.Net http://www.team.net/donate.html
>>
>>You are subscribed as jeff@v8tiger.demon.co.uk
>>
>>Tigers@autox.team.net
>>http://autox.team.net/mailman/listinfo/tigers
>>
>>http://www.team.net/archive
>>
>
> --
> Jeff Howarth
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
>
> You are subscribed as thorlp@hotmail.com
>
> Tigers@autox.team.net
> http://autox.team.net/mailman/listinfo/tigers
>
> http://www.team.net/archive
_________________________________________________________________
With Windows Live, you can organize, edit, and share your photos.
http://www.windowslive.com/Desktop/PhotoGallery
_______________________________________________
Support Team.Net http://www.team.net/donate.html
Tigers@autox.team.net
http://autox.team.net/mailman/listinfo/tigers
http://www.team.net/archive
|