Not for a few washers popped in a sturdy envelope as regular
unregistered mail!
Kees Oudesluijs
Op 13-1-2017 om 16:27 schreef Neil Anderson:
> Bob,
>
> FWIW, there would be no VAT on export orders from the UK, but shipping
> is getting really expensive.
>
> Neil Anderson
> BT7
>
> On Thu, Jan 12, 2017 at 11:04 AM, Bob Spidell <bspidell at comcast.net
>
> Well, I went ahead and ordered from Moss. I did a cursory check
> of the interwebs didn't turn up anything of those dimensions here:
>
> https://www.mcmaster.com/#standard-washers/=15uvd84
> <https://www.mcmaster.com/#standard-washers/=15uvd84>
>
> and here:
>
>
> http://www.keybellevilles.com/bellevilles/sampleCatalog.php?gclid=CMCHjPHOuNECFQGRfgodVAoFuA
>
> <http://www.keybellevilles.com/bellevilles/sampleCatalog.php?gclid=CMCHjPHOuNECFQGRfgodVAoFuA>
>
> and others, and I need to get this car back together before I
> start losing the little bits. FWIW, SC Parts and AH Spares have
> them at a more reasonable price--esp. with the current exchange
> rate--but with VAT and shipping it's not a massive savings.
>
> My thanks to Olin, Bob and others who responded; if I come across
> these in this size I'll make a note for future reference. Now, at
> least, I know what they're for and how to stack them.
>
> Bob
>
>
> On 1/10/2017 2:14 PM, Olin Brimberry wrote:
>> Bob,
>>
>> I figured height of the spring was also important, so I put 2 together
>> and measured the height with calipers
>> Height of 2 washers: 0.100 inches
>> Height of 1 washer: 0.050 inches
>> Thickness of washer: 0.025 inches
>> Checking the previous diameter dimensions with a caliper, I get:
>>
>> ID: 1.057 inches
>> OD: 1.5 inches
>>
>> I suspect that the ID is originally spec'd to be 1-1/16" but because of
>> the slight "spring", the diameter is slightly less. Good luck
>>
>> Olin K. Brimberry, PE
>> Principal Engineer
>> Office -919.803.4274 <tel:%28919%29%20803-4274>
>> Mobile -919.522.1608 <tel:%28919%29%20522-1608>
>>
>> HunterBane Engineering, PLLC
>> PO Box 10314
>> Raleigh, NC 27605
>> 3306 Alamance Drive
>> Raleigh, NC 27609
>>
>>
>>
>> -----Original Message-----
>> Sent: Tuesday, January 10, 2017 4:34 PM
>> Subject: RE: [Healeys] Belleville washers in BN2 steering box
>>
>> I just pulled mine out of a steering box I am rebuilding, and yes there
>> are 6 positioned as such: ()()() Where only the outer edges touch. The
>> dimensions are as follows:
>>
>> ID: 1-1/16
>> OD: 1-1/2
>> Pictures of the measurements are attached for verification purposes.
>>
>> The washers were loose on the shaft, but I think the closer tolerance is
>> going to be on the OD side.
>>
>> Olin K. Brimberry, PE
>> Principal Engineer
>> Office -919.803.4274 <tel:%28919%29%20803-4274>
>> Mobile -919.522.1608 <tel:%28919%29%20522-1608>
>>
>> HunterBane Engineering, PLLC
>> PO Box 10314
>> Raleigh, NC 27605
>> 3306 Alamance Drive
>> Raleigh, NC 27609
>>
>>
>>
> _______________________________________________ Support Team.Net
> http://www.team.net/donate.html <http://www.team.net/donate.html>
> Suggested annual donation $12.75 Archive:
> http://www.team.net/archive Forums: http://www.team.net/forums
> http://autox.team.net/mailman/listinfo/healeys
> <http://autox.team.net/mailman/listinfo/healeys>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/neilandcustom at gmail.com
> <http://autox.team.net/mailman/options/healeys/neilandcustom at gmail.com>
>
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/coudesluijs
> at chello.nl
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20170113/7f9e9743/attachment.html>
|