--===============8577950316507196524==
--Apple-Mail-15--468176749
Content-Transfer-Encoding: quoted-printable
charset=us-ascii
Here are some instructions for that section of the transmission. Toyota =
calls the end of the transmission the "extension" and the tower is the =
"shifter retainer"
http://www.cygnusx1.net/supra/library/tsrm/mk2/manual.aspx?S=3DMT&P=3D31
On Dec 15, 2015, at 6:23 PM, richard mayor wrote:
> Well..... my experience is a bit different. =20
> The shift towers come in about 6 different locations. In whatever =
position it is, there is a long shifter rod that extends from the front =
half into the back half of the transmission. The shifter stick has a =
ball on the end that goes down into a cup, and that cup is at the end of =
an arm, and that arm is bolted to the shifter rod. Depending on the =
shift tower position, the length of the arm is different. You cannot =
simply bolt on a different shift tower and have the stick match up with =
the cup in the old shifter arm.=20
> When I converted a Supra transmission (W58 with rear tower position) =
to a front shift tower position (W59 2 wheel drive truck), and I've done =
this twice, I seem to recall that I had to split the transmission in =
order to remove and replace the arm with a completely different length =
of arm.=20
>=20
> On Tue, Dec 15, 2015 at 12:44 PM, i erbs <eyera3000@gmail.com> wrote:
> good luck, not a universal endorsement of your veracity. I think this =
was a one off :)
>=20
> On Tue, Dec 15, 2015 at 11:27 AM, Michael Oritt =
<michael.oritt@gmail.com> wrote:
> Ira said: "Michael is correct."
>=20
> I am forwarding that to my wife and I am sure it will give her a good =
laugh.
>=20
> Best--Michael Oritt
>=20
> On Tue, Dec 15, 2015 at 2:00 PM, i erbs <eyera3000@gmail.com> wrote:
> Michael is correct. I have a 5 spd on my car. It's about where the =
shift tower is located. It just bolts to the top of the tranny. The only =
fabricating I did was to lengthen the fulcrum point for the slave arm on =
the side of the tranny.
>=20
> On Tue, Dec 15, 2015 at 10:48 AM, Michael Oritt =
<michael.oritt@gmail.com> wrote:
> Gary--
>=20
> My "Smitty's Instructions" are not close at hand but my recollection =
is that there are three different locations available for the shifter =
depending upon which tower is used. None requires any adaption, =
etc.--they are simply alternative Toyota parts.
>=20
> Best--Michael Oritt
> BN1 w/Toyota 5-speed
>=20
> On Tue, Dec 15, 2015 at 10:03 AM, <warthodson@aol.com> wrote:
> A friend is installing a Toyota 5-speed conversion kit. One of the =
changes required is installing a forward shift tower & "housing shift" =
#33521-35221", but the instructions do not explain how this is done. =
The part we do not understand is how to install the new housing shift =
onto the existing shaft. Does the transmission need to be split in half =
to access the shifter shaft? Has anyone done this & could you explain =
the process? Does anyone know what I am talking about?
> Thanks,
> Gary Hodson
> =20
>=20
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>=20
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>=20
> Unsubscribe/Manage: =
http://autox.team.net/mailman/options/healeys/michael.oritt@gmail.com
>=20
>=20
>=20
>=20
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>=20
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>=20
> Unsubscribe/Manage: =
http://autox.team.net/mailman/options/healeys/eyera3000@gmail.com
>=20
>=20
>=20
>=20
>=20
>=20
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>=20
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>=20
> Unsubscribe/Manage: =
http://autox.team.net/mailman/options/healeys/boyracer466@gmail.com
>=20
>=20
>=20
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>=20
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>=20
> Unsubscribe/Manage: =
http://autox.team.net/mailman/options/healeys/e-wilkins@cox.net
>=20
--Apple-Mail-15--468176749
Content-Transfer-Encoding: quoted-printable
charset=us-ascii
<html><head></head><body style=3D"word-wrap: break-word; =
-webkit-nbsp-mode: space; -webkit-line-break: after-white-space; =
"><div>Here are some instructions for that section of the transmission. =
Toyota calls the end of the transmission the "extension" and the tower =
is the "shifter retainer"</div><div><br></div><div><a =
href=3D"http://www.cygnusx1.net/supra/library/tsrm/mk2/manual.aspx?S=3DMT&=
amp;P=3D31">http://www.cygnusx1.net/supra/library/tsrm/mk2/manual.aspx?S=3D=
MT&P=3D31</a></div><br><div><div>On Dec 15, 2015, at 6:23 PM, =
richard mayor wrote:</div><br =
class=3D"Apple-interchange-newline"><blockquote type=3D"cite"><div =
dir=3D"ltr"><div><div>Well..... my experience is a bit different. =
<br></div>The shift towers come in about 6 different locations. In =
whatever position it is, there is a long shifter rod that extends from =
the front half into the back half of the transmission. The shifter =
stick has a ball on the end that goes down into a cup, and that cup is =
at the end of an arm, and that arm is bolted to the shifter rod. =
Depending on the shift tower position, the length of the arm is =
different. You cannot simply bolt on a different shift tower and have =
the stick match up with the cup in the old shifter arm. <br></div>When I =
converted a Supra transmission (W58 with rear tower position) to a front =
shift tower position (W59 2 wheel drive truck), and I've done this =
twice, I seem to recall that I had to split the transmission in order to =
remove and replace the arm with a completely different length of arm. =
<br></div><div class=3D"gmail_extra"><br><div class=3D"gmail_quote">On =
Tue, Dec 15, 2015 at 12:44 PM, i erbs <span dir=3D"ltr"><<a =
href=3D"mailto:eyera3000@gmail.com"; =
target=3D"_blank">eyera3000@gmail.com</a>></span> =
wrote:<br><blockquote class=3D"gmail_quote" style=3D"margin:0 0 0 =
.8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir=3D"ltr">good =
luck, not a universal endorsement of your veracity. I think this was a =
one off :)<div class=3D"gmail_extra"><br><div class=3D"gmail_quote">On =
Tue, Dec 15, 2015 at 11:27 AM, Michael Oritt <span dir=3D"ltr"><<a =
href=3D"mailto:michael.oritt@gmail.com"; =
target=3D"_blank">michael.oritt@gmail.com</a>></span> =
wrote:<br><blockquote class=3D"gmail_quote" style=3D"margin:0 0 0 =
.8ex;border-left:1px #ccc solid;padding-left:1ex"><div =
dir=3D"ltr"><div><font color=3D"#3333ff">Ira said: </font><i =
style=3D"color:rgb(51,51,255)">"Michael is correct."</i></div><div><i =
style=3D"color:rgb(51,51,255)"><br></i></div><div><span =
style=3D"color:rgb(51,51,255)">I am forwarding that to my wife and I am =
sure it will give her a good laugh.</span></div><div><span =
style=3D"color:rgb(51,51,255)"><br></span></div><div><span =
style=3D"color:rgb(51,51,255)">Best--Michael =
Oritt</span></div></div><div><div><div class=3D"gmail_extra"><br><div =
class=3D"gmail_quote">On Tue, Dec 15, 2015 at 2:00 PM, i erbs <span =
dir=3D"ltr"><<a href=3D"mailto:eyera3000@gmail.com"; =
target=3D"_blank">eyera3000@gmail.com</a>></span> =
wrote:<br><blockquote class=3D"gmail_quote" style=3D"margin:0 0 0 =
.8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir=3D"ltr">Michael=
is correct. I have a 5 spd on my car. It's about where the shift tower =
is located. It just bolts to the top of the tranny. The only fabricating =
I did was to lengthen the fulcrum point for the slave arm on the side of =
the tranny.</div><div class=3D"gmail_extra"><br><div =
class=3D"gmail_quote"><div><div>On Tue, Dec 15, 2015 at 10:48 AM, =
Michael Oritt <span dir=3D"ltr"><<a =
href=3D"mailto:michael.oritt@gmail.com"; =
target=3D"_blank">michael.oritt@gmail.com</a>></span> =
wrote:<br></div></div><blockquote class=3D"gmail_quote" style=3D"margin:0 =
0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div><div><div =
dir=3D"ltr"><div style=3D"color:#3333ff">Gary--</div><div =
style=3D"color:#3333ff"><br></div><div style=3D"color:#3333ff">My =
"Smitty's Instructions" are not close at hand but my recollection is =
that there are three different locations available for the shifter =
depending upon which tower is used. None requires any adaption, =
etc.--they are simply alternative Toyota parts.</div><div =
style=3D"color:#3333ff"><br></div><div =
style=3D"color:#3333ff">Best--Michael Oritt</div><div =
style=3D"color:#3333ff">BN1 w/Toyota 5-speed</div></div><div =
class=3D"gmail_extra"><br><div class=3D"gmail_quote"><span>On Tue, Dec =
15, 2015 at 10:03 AM, <span dir=3D"ltr"><<a =
href=3D"mailto:warthodson@aol.com"; =
target=3D"_blank">warthodson@aol.com</a>></span> =
wrote:<br></span><blockquote class=3D"gmail_quote" style=3D"margin:0 0 0 =
.8ex;border-left:1px #ccc solid;padding-left:1ex"><div><div><font =
face=3D"arial" color=3D"black" size=3D"2">
<div><font style=3D"background-color:transparent">A friend is installing =
a Toyota 5-speed conversion kit. One of the changes required is =
installing a forward shift tower & "housing shift" #33521-35221", =
but the instructions do not explain how this is done. The part we =
do not understand is how to install the new housing shift onto the =
existing shaft. Does the transmission need to be split in half to access =
the shifter shaft? Has anyone done this & could you explain the =
process? Does anyone know what I am talking about?</font></div>
<div>Thanks,</div>
<div>Gary Hodson </div>
<div> </div>
=
</font><br></div></div><span>_____________________________________________=
__<br>
Support <a href=3D"http://Team.Net";>Team.Net</a> <a =
href=3D"http://www.team.net/donate.html"; rel=3D"noreferrer" =
target=3D"_blank">http://www.team.net/donate.html</a><br>
Archive: <a href=3D"http://www.team.net/archive"; rel=3D"noreferrer" =
target=3D"_blank">http://www.team.net/archive</a><br>
Forums: <a href=3D"http://www.team.net/forums"; rel=3D"noreferrer" =
target=3D"_blank">http://www.team.net/forums</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; =
target=3D"_blank">Healeys@autox.team.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; =
rel=3D"noreferrer" =
target=3D"_blank">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br></span>
href=3D"http://autox.team.net/mailman/options/healeys/michael.oritt@gmail.=
com" rel=3D"noreferrer" =
target=3D"_blank">http://autox.team.net/mailman/options/healeys/michael.or=
itt@gmail.com</a><br>
<br>
<br></blockquote></div><br></div>
<br>_______________________________________________<br>
Support <a href=3D"http://Team.Net";>Team.Net</a> <a =
href=3D"http://www.team.net/donate.html"; rel=3D"noreferrer" =
target=3D"_blank">http://www.team.net/donate.html</a><br>
Archive: <a href=3D"http://www.team.net/archive"; rel=3D"noreferrer" =
target=3D"_blank">http://www.team.net/archive</a><br>
Forums: <a href=3D"http://www.team.net/forums"; rel=3D"noreferrer" =
target=3D"_blank">http://www.team.net/forums</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; =
target=3D"_blank">Healeys@autox.team.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; =
rel=3D"noreferrer" =
target=3D"_blank">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br></div></div>
href=3D"http://autox.team.net/mailman/options/healeys/eyera3000@gmail.com"=
rel=3D"noreferrer" =
target=3D"_blank">http://autox.team.net/mailman/options/healeys/eyera3000@=
gmail.com</a><br>
<br>
<br></blockquote></div><br></div>
</blockquote></div><br></div>
</div></div></blockquote></div><br></div></div>
<br>_______________________________________________<br>
Support <a href=3D"http://Team.Net";>Team.Net</a> <a =
href=3D"http://www.team.net/donate.html"; rel=3D"noreferrer" =
target=3D"_blank">http://www.team.net/donate.html</a><br>
Archive: <a href=3D"http://www.team.net/archive"; rel=3D"noreferrer" =
target=3D"_blank">http://www.team.net/archive</a><br>
Forums: <a href=3D"http://www.team.net/forums"; rel=3D"noreferrer" =
target=3D"_blank">http://www.team.net/forums</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net";>Healeys@autox.team.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; =
rel=3D"noreferrer" =
target=3D"_blank">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br>
href=3D"http://autox.team.net/mailman/options/healeys/boyracer466@gmail.co=
m" rel=3D"noreferrer" =
target=3D"_blank">http://autox.team.net/mailman/options/healeys/boyracer46=
6@gmail.com</a><br>
<br>
<br></blockquote></div><br></div>
_______________________________________________<br>Support <a =
href=3D"http://Team.Net";>Team.Net</a> <a =
href=3D"http://www.team.net/donate.html";>http://www.team.net/donate.html</=
a><br>Suggested annual donation $12.75<br>Archive: <a =
href=3D"http://www.team.net/archive";>http://www.team.net/archive</a><br>Fo=
rums: <a =
href=3D"http://www.team.net/forums";>http://www.team.net/forums</a><br><br>=
<a =
href=3D"mailto:Healeys@autox.team.net";>Healeys@autox.team.net</a><br>http:=
//autox.team.net/mailman/listinfo/healeys<br><br>Unsubscribe/Manage: =
http://autox.team.net/mailman/options/healeys/e-wilkins@cox.net<br><br></b=
lockquote></div><br></body></html>=
--Apple-Mail-15--468176749--
--===============8577950316507196524==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============8577950316507196524==--
|