Re: [Fot] Thrust Bearing fabrication question?

[fubog1 via Fot <fot@autox.team.net>]

--===============8037221610916785526==
        boundary="----=_Part_169276_1758324491.1677189577902"

------=_Part_169276_1758324491.1677189577902
Content-Transfer-Encoding: quoted-printable

 Mine are #8 countersunk machine screws, 3 in each half, & the thrust face =
has an annular groove that's pressure fed, tapped off a small drilling to t=
he rear main.
Glen Efinger
=20
=20
-----Original Message-----
From: David Cutter via Fot <fot@autox.team.net>
To: fot@autox.team.net
Sent: Thu, Feb 23, 2023 10:29 am
Subject: [Fot] Thrust Bearing fabrication question?

Amici, fabricating some full 360 degree thrust bearings for the first time.=
=C2=A0 What is the recommended method for fastening them?=C2=A0 Pin or othe=
r fastener?=C2=A0 Fasten both halves or just the upper half?
Thanks!DaveSpitfire #42

_______________________________________________
fot@autox.team.net

http://www.fot-racing.com

Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
m



------=_Part_169276_1758324491.1677189577902
Content-Transfer-Encoding: 7bit


<div style="color:black;font: 10pt Arial, Helvetica, sans-serif;">
<div> <font size="2">Mine are #8 countersunk machine screws, 3 in each half, 
&amp; the thrust face has an annular groove that's pressure fed, tapped off a 
small drilling to the rear main.</font></div>

<div><br>
</div>

<div><font size="2">Glen Efinger</font><br>
</div>

<div> <br>
</div>

<div> <br>
</div>

<div style="font-family:arial,helvetica;font-size:10pt;color:black"><font 
size="2">-----Original Message-----<br>
From: David Cutter via Fot &lt;fot@autox.team.net&gt;<br>
To: fot@autox.team.net<br>
Sent: Thu, Feb 23, 2023 10:29 am<br>
Subject: [Fot] Thrust Bearing fabrication question?<br>
<br>

<div id="yiv6954438538">
<div dir="ltr">Amici, fabricating some full 360 degree thrust bearings for the 
first time.&nbsp; What is the recommended method for fastening them?&nbsp; Pin 
or other fastener?&nbsp; Fasten both halves or just the upper half?
<div><br>
</div>

<div>Thanks!</div>

<div>Dave</div>

<div>Spitfire #42</div>

<div><br>
</div>

<div><br>
</div>
</div>

</div>
_______________________________________________<br>
<a ymailto="mailto:fot@autox.team.net"; 
href="mailto:fot@autox.team.net";>fot@autox.team.net</a><br>
<br>
<a href="http://www.fot-racing.com/"; 
target="_blank">http://www.fot-racing.com</a><br>
<br>
Archive: <a href="http://autox.team.net/archive"; 
target="_blank">http://autox.team.net/archive </a><a 
href="http://www.team.net/pipermail/fot"; 
target="_blank">http://www.team.net/pipermail/fot</a><br>
<br>
<br>
</font></div>
</div>

------=_Part_169276_1758324491.1677189577902--

--===============8037221610916785526==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________
fot@autox.team.net

http://www.fot-racing.com

Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot



--===============8037221610916785526==--