fot
[Top] [All Lists]

Re: [Fot] Alloy v steel

To: "Kas Kastner" <kaskas@cox.net>
Subject: Re: [Fot] Alloy v steel
From: "Greg \"Lunker\" Hilyer" <lunkercars@earthlink.net>
Date: Sun, 18 Nov 2007 18:34:23 -0700
Please elaborate a bit Kas. I've never heard of a steel flywheel for  
a TR. I always assumed they were all cast iron as OEM. Were there  
some that were steel from the factory? Or were the steel ones  
something "trick" from days gone bye? As I recall, my stock flywheel  
was originally something around 33lbs. and after getting it down to  
around 22, I have to agree that I couldn't see where any additional  
weight could be safely taken  off.
FWIW - I did find the difference to be noticeable [for the better]  
minus that 11lbs. - been a bit leery of going alloy.
Also, I've been considering either a TR6 flywheel [for the TR4] or re- 
drilling my TR4 flywheel for the sake of the [much lighter] TR6  
diaphragm  type pressure pressure plate. - Any thoughts?
Thanks in advance,
Greg Hilyer
TR4 #314
Albuquerque NM


On Nov 18, 2007, at 5:26 PM, Kas Kastner wrote:

> It is sometimes confusing when referring to other than alloy  
> flywheels, some
> are steel and others are CAST IRON. With a steel wheel I can see  
> getting the
> weight out of the outside diameter and the total down but I'd be  
> very very
> careful doing this with cast iron.
> ----- Original Message -----
> From: <N197TR4@cs.com>
> To: "Tony Drews" <tony@tonydrews.com>; "Jim Cun"  
> <jimcun2001@yahoo.com.au>;
> "Friends of Triumph" <fot@autox.team.net>
> Sent: Sunday, November 18, 2007 1:57 PM
> Subject: Re: [Fot] Alloy v steel
>
>
>> I like my steel flywheel....trouble free and like a piece of  
>> jewelry that I
>> hated to cover up.
>>
>> Joe
>>
>>
>>
>>> Alloy flywheels seem harder to keep attached to the crankshaft.   
>>> With
>>> proper care, they work well, though.  They seem to be more
>>> troublesome in the 6 cylinder motors, anecdotally.
>>>
>>> - Tony
>>>
>>> At 03:01 PM 11/18/2007, Jim Cun wrote:
>>>> Hi Guys,
>>>>           Just wanted to ask your thoughts on an alloy flywheel vs
>>>> steel for a TR race car?
>>>>
>>>> Regards Jim
>>>>
>>>>
>>>>       Make the switch to the world's
>>>> best email. Get the new Yahoo!7 Mail now.
>>>> http://au.yahoo.com/worldsbestmail/viagra/index.html
>>>> _______________________________________________
>>>> http://www.team.net/donate.html
>>>>
>>>> Fot mailing list
>>>> Fot@autox.team.net
>>>> http://autox.team.net/mailman/listinfo/fot
>>> _______________________________________________
>>> http://www.team.net/donate.html
>>>
>>> Fot mailing list
>>> Fot@autox.team.net
>>> http://autox.team.net/mailman/listinfo/fot
>> _______________________________________________
>> http://www.team.net/donate.html
>>
>> Fot mailing list
>> Fot@autox.team.net
>> http://autox.team.net/mailman/listinfo/fot
> _______________________________________________
> http://www.team.net/donate.html
>
> Fot mailing list
> Fot@autox.team.net
> http://autox.team.net/mailman/listinfo/fot
_______________________________________________
http://www.team.net/donate.html

Fot mailing list
Fot@autox.team.net
http://autox.team.net/mailman/listinfo/fot

<Prev in Thread] Current Thread [Next in Thread>