datsun-roadsters
[Top] [All Lists]

Re: [Roadsters] head bolts

To: jh.bahn@verizon.net
Subject: Re: [Roadsters] head bolts
From: "DatsunParts.com, Inc." <datsunpartsdotcom@gmail.com>
Date: Thu, 1 Aug 2013 08:45:13 -0700
Cc: datsun-roadsters@autox.team.net
Delivered-to: mharc@autox.team.net
Delivered-to: datsun-roadsters@autox.team.net
References: <FB7DA719-7909-42B8-8E74-534548B652CF@shaw.ca> <DB453C98163E43A49CA773D62F863686@BahnTHINK>
The head stud numbers you list are incorrect and are not 2000 head stud
part numbers,

Dean


On Thu, Aug 1, 2013 at 6:53 AM, <jh.bahn@verizon.net> wrote:

> Do you heave head bolts (usual case) or head studs fastened with nuts?  If
> the head has been overly milled (that would usually case come piston slap
> and head or valve damage) you might want to try studs.
>
> Head Stud
> ARP        AP5.000        7/16b  dia. 5 or 5-1/4 in. long; coarse thread
> for block and fine thread for nut
> ARP        AP5.250
> Nut
> ARP        10-APN12-1
> Washer
> ARP        10-APN1316N
>
> 'Course ARP also makes head bolts.   http://www.arp-bolts.com/
>
>
> -----Original Message----- From: jamie tousignant
> Sent: Thursday, August 01, 2013 2:30 AM
> To: datsun-roadsters@autox.team.**net <datsun-roadsters@autox.team.net>
> Subject: [Roadsters] head bolts
>
> hey anyone have experience with head bolts and washers  to take up the
> difference in a head?after being surfaced
> i have a 2litre that has compression loss after less than 1200 miles on it
> since rebuild  of  and notice the builder used washers
> under the head bolt nuts it was  5 on one and 4 on another  down to 2 in
> the
> middle  which i believe would cause the  pressure to be different
> when being tightened  ? has anyone had their studs threaded longer to
> remove
> the need to do the washer trick?
> i know you can purchase shims for the towers to take up the slack if needed
> but  am struggling to work out a solution
> for this problem
> ______________________________**__________
>
> datsun-roadsters@autox.team.**net <datsun-roadsters@autox.team.net>
>
> Donate: http://www.team.net/donate.**html<http://www.team.net/donate.html>
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe: http://autox.team.net/mailman/**options/datsun-roadsters/**
> vze3bsfc@verizon.net<http://autox.team.net/mailman/options/datsun-roadsters/vze3bsfc@verizon.net>
>
> ______________________________**__________
>
> datsun-roadsters@autox.team.**net <datsun-roadsters@autox.team.net>
>
> Donate: http://www.team.net/donate.**html<http://www.team.net/donate.html>
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe: http://autox.team.net/mailman/**options/datsun-roadsters/**
> datsunpartsdotcom@gmail.com<http://autox.team.net/mailman/options/datsun-roadsters/datsunpartsdotcom@gmail.com>
>
>
>


-- 
*Thank you for allowing us to serve you with your Datsun's needs!*

*Dean Apostal*

______________________________________________________________
<http://www.datsunparts.com>
DatsunParts.com, Inc.
18735 Bryant St.
Northridge, CA  91324
(818) 363-2015
Hours (Pacific Time)
Tues - Thur 10:00 AM - 3:00 PM
sales@datsunparts.com
________________________________________

datsun-roadsters@autox.team.net

Archive: http://www.team.net/archive
Unsubscribe: 
http://autox.team.net/mailman/options/datsun-roadsters/mharc@autox.team.net


<Prev in Thread] Current Thread [Next in Thread>