What he lists below is a "built" motor not a rebuilt. A rebuilt is use what
you have if it is OK. Replace what is not.
----- Original Message -----
From "David Riker" <davriker at pacbell.net>
To: "David Ramsey" <dwramsey@worldnet.att.net>; <BritishCarMan@aol.com>
Cc: <spridgets@autox.team.net>
Sent: Sunday, January 21, 2001 11:49 PM
Subject: Re: Engine on Ebay
> Crash:
> Throwing the header and weber prices into the total is cheating! While
you
> are at it, what about a nice aluminum head, ported and flow benched, total
> seal rings, custom oil pan with windage tray, lightened aluminum flywheel,
> alloy valve cover, aluminum radiator, serpentine belt ancillary drive,
> electronic coil over plug ignition with crank position sensor, electric
> water pump? Oh, yeah, and the $4500 supercharger setup too. I bet we
could
> spend $15k of your money on my dream engine real easy...
> David Riker
> 74 Midget
> 63 Falcon
> 70 Torino
> http://home.pacbell.net/davriker
> ----- Original Message -----
> From: "David Ramsey" <dwramsey@worldnet.att.net>
> To: <BritishCarMan@aol.com>
> Cc: <spridgets@autox.team.net>
> Sent: Sunday, January 21, 2001 12:28 PM
> Subject: Re: Engine on Ebay
>
>
> > Jamie, I'm getting the parts from many different places, APT, Summit
> > Racing, Crane, and on the net.
> > Stock power for a 948 is 43hp @ 5k rpm. I also finished a high level
> > "show" stock rebuild two years ago for close to $3k. That included NOS
> > steel water pump, lever arm fuel pump, all correct hoses & clamps, and
> total
> > rebuild of my 1 1/4" H1 SU's. There are pictures of this engine
floating
> > around on the list.
> > My local machine shop will do a quality long block for around
> $1500,
> > another local shop will also do it for the same amount and it will last
2
> > months.
> > The cost difference between doing a 948 and 1275 are nil and if
> > going to a ribcase your making a big mistake (5- speed is the only way
to
> > go).
> > Some parts for my rebuild are:
> > balanced, nitrated, wedged crank $700
> > belt drive $250
> > Crane lifters & push rods $160
> > balanced lightened rods $400
> > three ring flat top pistons $400
> > All ARP bolts and nuts/studs $250
> > Manaflow LCB Jet-hot coated $300
> > 40 dcoe Weber/ cannon manifold/ K&N filter with stacks $500
> > High-volume oil pump $150
> > Vandervell bearing shells $90
> > For a total of $3200 just in these parts.
> > Add in for extras and machine work I'll be lucky to hold it under $5k.
> > This will all be in front of a Datsun 5-speed and 4.22 rear.
> > I can do a ring/valve & shell rebuild for around $300
> >
> >
> > >Good lord Crash, who are you getting parts from? I'm keeping mine all
> > >original except the cam. Stock power I beleive is 53 hp or was it 48.
If
> I
> > >were to put a bunch of high performance stuff on it then I would
probley
> > >spend a bundle. My head is still good so I don't have to worry about
> that.
> > If
> > >I were to figure up $3500.00 for a engine rebuild I would just go ahead
> and
> > >throw a 1275 w/rib case tranny in.
> > >
> > >Jamie
|