Hi Bryan,
It is a cast aluminum, so I'll try grinding some of the material off. I
didn't coat the exhaust header with anything, is that a recommended
practice? I was planning on putting some kind of small heat shield
between the manifolds, hopefully I'll be able to grind off enough material
to be able to do that. Thanks again!
Greg Gowins
Dublin, CA
'69 Sprite
On Wed, 15 Sep 1999, Bryan Vandiver wrote:
> Greg,
>
> I'm glad to here that one of my suggestions worked :-)
>
> I am using a dellorto sidedraft (basically the same as a weber DCOE) with my
>maniflow LCB header.
> I assume your intake manifold is made of cast aluminum. The metal is probably
>thick enough that you
> can grind off enough from the intake manifold so that it doesn't contact the
>header, and you really
> don't want them touching anyway because of the heat that would be transferred.
>
> BTW - did you coat the header with anything prior to installing, or just
>leave it bare metal?
> I used the 'stainless steel' exhaust coating from Eastwood on mine, and sor
>far it seems to be
> holding up pretty well. The stuff is really thick and has to be brushed on,
>and 'cures' the first
> time you run the engine with it. The other 'high temperature' aluminum
>exhaust paint that I used on
> the rest of the system hasn't faired as well, and is bubbling in several
>areas.
>
> Regards - Bryan
> >To: "Spridgets List" <spridgets@autox.team.net>
> >Subject: Maniflow header installed, BUT....
> >MIME-Version: 1.0 charset="iso-8859-1"
> >X-Priority: 3 (Normal)
> >X-MSMail-Priority: Normal
> >X-MimeOLE: Produced By Microsoft MimeOLE V5.00.2014.211
> >Importance: Normal
> >
> >Hello fellow listers,
> >
> >Thanks again for all of the recommendations on getting my Maniflow header
> >installed. I finally got it in on Friday, using Bryan's pull the head
> >method. Since I had to put new head studs in, it wasn't too much of a
> >hassle. It took a little wiggling, but the header dropped right into place
> >without having to rock the engine or cut any metal around the original
> >exhaust tube hole. Now here comes the but...
> >
> >I put everything back on the engine, and when I started the engine, she
> >fired right up. But instead of idling, the RPMs kept rising, quickly. Shut
> >everything down, checked the obvious, like the throttle return spring or a
> >sticking choke. Everything checked out fine. A little more research, and I
> >was leaking gas below the intake manifold ports on the head. No prob, I
> >must not have tightened the bolts down enough. Rechecked and they were
> >fine. A little more looking, and I realized that the middle tube of the new
> >exhaust manifold was supporting the intake manifold keeping it from seating
> >down all the way!!! It was short of seating on the gasket by about a 1/8 of
> >an inch on the bottom of the intake port.
> >
> >I have a Weber DFV carb (just like a DGV, only different) and am wondering
> >what my options are right now. Are there any spacers I can get to push the
> >intake manifold away from the head a bit, ala the SU's? Or am I stuck
> >getting a new manifold, in which case it would cause me to have no choice
> >but to upgrade to DCOEs...<grin> Any help is much appreciated. Thanks!
> >
> >Greg Gowins
> >'69 Sprite
> >Dublin, CA
> >
> >PS Sorry I missed the event in Palo Alto. It sounded like a blast. I was
> >planning on attending, but it was opening weekend of soccer season, and at
> >the end of the game, my only thoughts were on getting in the hot tub back at
> >the apartments! I'm getting old WAY too quick...
> >
> >
> >
>
>
|