land-speed
[Top] [All Lists]

Re: Fuel and Gas Class

To: john robinson <john@engr.wisc.edu>
Subject: Re: Fuel and Gas Class
From: dahlgren <dahlgren@uconect.net>
Date: Wed, 24 May 2000 14:55:07 -0400
I am losing something here the big speed secret and obvious advantage of
rear steer is ????????????????????????????????????
Dahlgren

john robinson wrote:
> 
> Howdy,
>           well now lets see..............
>          ifn you take a long narrow streamliner with the front wheel drive
> non steering, and put the driver behind the engine, and then behind him the
> staggered rear steering wheels with only about 8 inches track, you would
> use a mustang steering rack(#1) between the two rear wheels, and then take
> two mustang steering racks and weld them together so the driver input would
> go forwards, then backwards to the actual steering rack (#1),( which would
> reverse the steering, the steered wheels would turn left as the driver
> turned his wheel right, making the car GO right. )
>          The kicker is that there is a delay between what the driver feels,
> and his input, which can produce a pilot induced oscillation as he tries to
> catch up to the actual motion of the car. This motion is considered to be
> at about 1 Hz (the driver makes a correction, the car SLOWLY begins to
> respond, the driver inputs additional steering,because he "feels" that the
> car is not responding correctly, then he finds the car to be correcting too
> quickly and he reverses his inputs, always chasing the vehicle, and causing
> finally an out of control situation. This can be seen when watching a
> single engined taildragger pilot learning to taxi the airplane for the
> first time.
>           However, I believe a disciplined driver CAN control a vehicle
> designed with rear steer. I think that if the driver is in the middle of
> the car, rather than the end, he would feel less steering input from the
> motion of the car, thereby would not feel the need to input corrections,
> and would not begin the PIO described above.
>          Wasn't the car Beckett drove a sports car of some sort? a short
> wheel base, wide track, mid engine something?  I think this would be very
> difficult to try to rear steer, VERY little visual input available to the
> driver for corrections, which is why I thought the driver positioned in the
> middle of a streamliner would be advantageous, lots of car left in front of
> him for visual reference, and less "feel" inputed to his butt than if he
> were in the tail of the car.
>          The reference to Thrust' $2 million computer was to the body
> positioning for aerodynamics, rather than controlling the actual steering,
> this is information from the magazine articles I have seen.
> 
> At 12:06 PM 5/24/00 , you wrote:
> >Now there is a Kernal of knowledge from Left Field.... Hey John... tell us
> >about this.... sounds interesting.. K
> >----- Original Message -----
> >From: John Beckett <landspeedracer@email.msn.com>
> >To: john robinson <john@engr.wisc.edu>; <land-speed@autox.team.net>
> >Sent: Wednesday, May 24, 2000 12:08 PM
> >Subject: Re: Fuel and Gas Class
> >
> >
> > >     John
> > >
> > >     I think what Dan was trying to say is the rear steer has been tried
> > > before mostly unsuccessfully. I know cause I was one that tried it. The
> >only
> > > high speed success that I am aware off was the Thrust project, but they
> >had
> > > a $2,000,000. computer making the necessary corrections for the "pilot".
> >If
> > > you asked Andy Green today about rear steer I don't think he would offer
> >any
> > > encouragement for the concept.
> > >     Another point I would like to make however, is that none of the
> > > governing bodies need to worry about adding rules to ban rear steer
> > > vehicles. It just doesn't work at speed and I don't believe you'll ever
> >get
> > > it going fast enough to get into trouble. And if you do somehow manage to
> > > make it work, well God bless you, innovation is what it's all about.
> > >
> > > John Beckett, LSR #79
> > >
> > > ----- Original Message -----
> > > From: "john robinson" <john@engr.wisc.edu>
> > > To: <land-speed@autox.team.net>
> > > Sent: Wednesday, May 24, 2000 9:57 AM
> > > Subject: Re: Fuel and Gas Class
> > >
> > >
> > > > Howdy,
> > > > ohhhh yeah, Definitions section IV-2 Automobile.(some snipping)  ....at
> > > > least 4 wheels not aligned....(snip).. steering assured by at least (2)
> > > > front wheels, .(snip) .....One pair must be on the same transverse
> > > centerline.
> > > > OK, then the Special Construction Category statement "Innovation is
> > > > unlimited." is governed by the definitions sec IV?
> > > > John still looking at rear steer concept Robinson
> > > >
> > > > At 08:22 AM 5/24/00 , you wrote:
> > > > John,
> > > >
> > > > Also look at the portion defining automobile which indicates that at
> >least
> > > > two wheels must be on the same axle. There is a statement that requires
> > > the
> > > > steering to be by the front wheels as our friends with the rear steer MR
> > > > found out a few years ago. Sorry I am unable to quote chapter and verse
> >on
> > > > this one as my books are in my race day brief case.
> > > >
> > > > Dan (you can lose pistons without NOS too) Warner
> > > > ----- Original Message -----
> > > > From: john robinson <john@engr.wisc.edu>
> > > > To: <land-speed@autox.team.net>
> > > > Sent: Wednesday, May 24, 2000 5:42 AM
> > > > Subject: Re: Fuel and Gas Class
> > > >
> > > >
> > > >  > howdy,
> > > >  > Andy Green did it like that, only cost 30 million $ or so and took
> > > what,
> > > >  > 6-7 years..........
> > > >  > I think you >can< run in line wheels, just need to have four of
> >them(or
> > > >  > more)  ifn I remember the rule book on this one....looking it up now,
> > > aha!
> > > >  > ...."must have at least four wheels, but they need not be arranged in
> >a
> > > >  > rectangular configuration" , Streamliner section V page 41....is what
> > > the
> > > >  > '00 rules say...
> > > >  >
> > > >  > At 10:13 AM 5/23/00 , you wrote:
> > > >  > Should still work, maybe? Per the rule book the wheels must be
> >offset,
> > > >  > cannot be inline. See Al teagues car. Otherwise isnit it classified
> >as
> > > a
> > > >  > "ahem" motorcycle or some such? But, adding the stagger control to
> >the
> > > > rear
> > > >  > does indeed work same as front stagger. Wow, what a concept!!!
> > > Shouldn't
> > > >  > take more'n ten years to sort it out...
> > > >  >
> > > >  > mayf
> > > >  > At 02:39 PM 5/23/00 EDT, V4GR@aol.com wrote:
> > > >  >  >Won't work in Jacks car. Front wheels are inline. Have to switch
> > > system
> > > > to
> > > >  >  >rear wheels. Should work than.  Rich Fox
> > > >  >  >
> > > >  >  >
> > > >  >
> > > >  >
> > > >  >
> > > >  > L.E. Mayfield
> > > >  > 124 Maximillion Drive
> > > >  > Madison, Al. 35758-8171
> > > >  > ph: 1-256-837-1051
> > > >  >
> > > >  > http://home.hiwaay.net/~lemay
> > > >  >
> > > >  > lemay@hiwaay.net
> > > >  >
> > > >  > Sunbeam Tiger, B9471136
> > > >  > Sunbeam Alpine Bonneville Land Speed Racer,
> > > >  > '66 Hydroplane Drag Boat (390 FE)
> > > >
> > > >
> > > >               John Robinson, Mechanician
> > > >    Mechanical Engineering University of Wisconsin
> > > >                  1513 University Ave.
> > > >                   Madison, Wi. 53706
> > > >                      608-262-3606
> > > >                    FAX 608-265-2316
> > > > Current World Land Speed Record Holder
> > > > Bonneville Salt Flats
> > > >             H/GCC 92 cu.in. 1980 Dodge Colt
> > > >    131.333 MPH set 1995
> > > >    136.666 MPH set 1996
> > > >
> > > >
> > >
> > >
> > >
> > >
> 
>               John Robinson, Mechanician
>    Mechanical Engineering University of Wisconsin
>                  1513 University Ave.
>                   Madison, Wi. 53706
>                      608-262-3606
>                    FAX 608-265-2316
>         Current World Land Speed Record Holder
>                  Bonneville Salt Flats
>             H/GCC 92 cu.in. 1980 Dodge Colt
>                    131.333 MPH set 1995
>                    136.666 MPH set 1996

<Prev in Thread] Current Thread [Next in Thread>