- 1. [TR] How much for a clutch job (score: 1)
- Author: "Ed Woods" <fogbro1@comcast.net>
- Date: Thu, 16 Sep 2010 10:08:52 -0400
- I have a set of Lucas LR6 driving lights on my TR3 (LR for Long Range, 6 inch diamenter). One light went out and the filament looks charred and there is a black tint on the upper lens. I am willing t
- /html/triumphs/2010-09/msg00219.html (7,180 bytes)
- 2. Re: [TR] How much for a clutch job (score: 1)
- Author: thenicholls@verizon.net
- Date: Thu, 16 Sep 2010 09:13:02 -0500 (CDT)
- - Car runs well and with full power for a while after start-up. - Loss of power and what feels like a miss under load after it's been driven a while. Going up a long hill seems to trigger the stumbl
- /html/triumphs/2010-09/msg00220.html (7,738 bytes)
- 3. Re: [TR] How much for a clutch job (score: 1)
- Author: Don Sforza <djsforza@gmail.com>
- Date: Thu, 16 Sep 2010 10:43:59 -0400
- Do you have any hard evidence that it's lack of fuel, like maybe a pressure reading? That is certainly where I would start, since a marginal ignition can cause exactly the same symptoms. Randall
- /html/triumphs/2010-09/msg00221.html (8,115 bytes)
- 4. Re: [TR] How much for a clutch job (score: 1)
- Author: Don Sforza <djsforza@gmail.com>
- Date: Thu, 16 Sep 2010 10:57:20 -0400
- Agree - check points, coil, rotor, etc. If the points aren't opening enough the coil's output isn't nearly as good. Sometimes when coils get hot they don't work so hot too (sorry) :) Being bolted to
- /html/triumphs/2010-09/msg00222.html (10,137 bytes)
- 5. Re: [TR] How much for a clutch job (score: 1)
- Author: thenicholls@verizon.net
- Date: Thu, 16 Sep 2010 09:49:47 -0500 (CDT)
- Man, nothing is making sense. I am changing out the upper control arm/fulcrum bushings on my TR3. I did one side last year and everything went smoothly. I was going to do the other side the following
- /html/triumphs/2010-09/msg00223.html (9,551 bytes)
- 6. Re: [TR] How much for a clutch job (score: 1)
- Author: "Randall" <tr3driver@ca.rr.com>
- Date: Thu, 16 Sep 2010 09:41:47 -0700
- i recently had the exact same problems on the 3. turned out i had developed a kink in one of the soft fuel lines that was restricting the flow of gas. Frank To: triumphs@autox.team.net Sent: Thu, Sep
- /html/triumphs/2010-09/msg00224.html (8,148 bytes)
- 7. Re: [TR] How much for a clutch job (score: 1)
- Author: TR250Driver@aol.com
- Date: Thu, 16 Sep 2010 18:54:43 -0400 (EDT)
- B B B B I checked the previously done side and found that indeed the outboard bolts have a captive nut at the bottom. B B B B -Bill B B B B B <snip> the mounting bolts for the upper fulcrum are all w
- /html/triumphs/2010-09/msg00230.html (8,116 bytes)
- 8. Re: [TR] How much for a clutch job (score: 1)
- Author: Andrew Mace <zoboherald@aol.com>
- Date: Thu, 16 Sep 2010 21:01:51 -0400
- taking apart tr-3 motor. found that big end rod bearings are .010 over. off the main bearing front and rear bearing/seal I find no notation of .010 but do find the number 0.254 MM above it another nu
- /html/triumphs/2010-09/msg00231.html (9,839 bytes)
- 9. Re: [TR] How much for a clutch job (score: 1)
- Author: Mark J Bradakis <mark@bradakis.com>
- Date: Thu, 16 Sep 2010 19:39:24 -0600
- 0.254mm is equal to 0.010 inches frank ________________________________ From: Gary Nafziger <nafzigerg@yahoo.com> To: triumphs@autox.team.net Sent: Fri, September 17, 2010 2:20:13 PM Subject: [TR] m
- /html/triumphs/2010-09/msg00232.html (8,126 bytes)
- 10. Re: [TR] How much for a clutch job (score: 1)
- Author: thenicholls@verizon.net
- Date: Thu, 16 Sep 2010 20:46:26 -0500 (CDT)
- Dean Mericas Dean: No sure but I assume that many on this list are also Formula 1 fanatics. With a purpose built track being planned and built in Austin, would you be so kind as to occasionally bring
- /html/triumphs/2010-09/msg00233.html (11,027 bytes)
- 11. Re: [TR] How much for a clutch job (score: 1)
- Author: thenicholls@verizon.net
- Date: Thu, 16 Sep 2010 20:47:25 -0500 (CDT)
- I need a straight upper fulcrum arm for a TR3A. This would be for the right side front or left side rear. It's a long story. Does anyone have one that they will sell? I see that Moss has them as NLA
- /html/triumphs/2010-09/msg00234.html (8,793 bytes)
This search system is powered by
Namazu