Fellow Ole Truckers: I am getting ready to start the process of work on the front end of my '56 Chevy 3100. One item of attention, is the tie rod and ends. I will be replacing with the new style tie
Gale: Thanks for the idea. However, I thought that you should not apply extreme heat to steering components. Kent S Butler '56 Chevy 3100 Houston, TX Fellow Ole Truckers: I am getting ready to start
Gale: Thanks for the idea. However, I thought that you should not apply extreme heat to steering components. Kent S Butler '56 Chevy 3100 Houston, TX Fellow Ole Truckers: I am getting ready to start
I am running stock wheels on my 59 GMC and they are 15 inch, 6 lug with clips. In fact I am running early 50's GMC hubcaps on the wheels. Pictures here http://www.stovebolt.com/gallery/dumkee_blaine
I don't see why you want to keep it at 6V. If your goal is to keep the truck pure then you need to find a wiring harness. But no matter if you keep 6V or go to 12V, 14 ga is ample for all lights, hor
I had an uncle who hauled cattle and built his own sideboards. He used oak and assembled the parts with carriage bolts. All members had all four edges eased with a router. The post were a full 2x3 an
Is the wire connected at both ends? The sending unit is MUCH more fragile than the gauge. If you pull the sending unit you'll probably find the little metal spiral broken. They aren't expensive. Remo
I am looking for a 1947-1955 chevy hood side emblem that reads either 4500 or 4600 is there such a thing? Mark --snip-- I haven't seen one but the side emblems are not the same for that many years. G
I am looking for a 1947-1955 chevy hood side emblem that reads either 4500 or 4600 is there such a thing? Mark --snip-- I haven't seen one but the side emblems are not the same for that many years.
I'm 1500 miles away from my 55-1 Chevy PU / 350 / 4L60E - wanting 5 speed - found rebuildable 92 Chevy 1500 5 speed / clutch & stuff. Sure I'm OK but before I buy / haul it home would like to know (
Hi All: I'm 1500 miles away from my 55-1 Chevy PU / 350 / 4L60E - wanting 5 speed - found rebuildable 92 Chevy 1500 5 speed / clutch & stuff. Sure I'm OK but before I buy / haul it home would like t
I'm hearing soda for paint but cannot verify it will remove rust? Would walnut be better? Thanks in advance. --snip-- Where is the rust? I have both sand and soda blasting equipment and often use a
I know this is a dumb question but Has anyone ever modified a 55 and newer tailgate to fit a 47-53 Box?? I have a 59 stepside Tailgate and a 48 Box!!! Rob...The ToonMan Sasquatch Artworks --snip-- I
Has anyone had experience with the Frantz toilet paper oil filter? Thinking about one for my '50 3600 and have only found positive feedback. thanks! Smokey League City, TX --snip-- No experience with
List, Can anyone confirm that the original, 1956, 1/2 ton front wheel spindles (I-beam and kingpin suspension) are the same? If not, then which is right and which is left? They appear identical to m
Well, there are no numbers on the parts themselves, the Assembly Manual shows the front axle, spindles, etc. as an assembly, so there are no individual part numbers listed for the spindles, and the S
Hi Gang: Got my head spinning - need some electrical routing help. Have GM 350 with PCM Engine Controls. Installed battery electrical shut off switch on the neg. side & routed a separate ground to t
Jim, What size/brand of diesel engine do plan to use in your 1955 GMC COE? I would love to use a diesel in my '51 3100. BobK --snip-- Gale Gorman Houston ____________________________________________
This is a Deerslayer episode called Project Nailhead. It is a short placekeeper log entry and introduces a new section where I will keep track of a '54 Buick 322 engine that I intend to rebuild. http
This is a Deerslayer episode called Project Nailhead. It is a short placekeeper log entry and introduces a new section where I will keep track of a '54 Buick 322 engine that I intend to rebuild. http