Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Land\-speed\]\s+rollcage\s+welding\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Land\-speed\]\s+rollcage\s+welding\s*$/: 7 ]

Total 7 documents matching your query.

1. [Land-speed] rollcage welding (score: 1): Author: "Benn" <karhu@california.com>; Date: Thu, 26 Feb 2009 09:28:33 -0800; Planning the rollcage for the MR2, and want to plant the main hoop as far outboard as possible. BUT, since it's behind the door opening, there is no way to weld the horizontal side (door) bars fully; /html/land-speed/2009-02/msg00073.html (7,337 bytes)
2. Re: [Land-speed] rollcage welding (score: 1): Author: "Dave Dahlgren" <ddahlgren@snet.net>; Date: Thu, 26 Feb 2009 13:22:53 -0500; Couldn't you tack everything to the main hoop but don't permanantly mount it in the car. Pop it out or slide it forward do the outside welds then drop it back in or slide it back with the door bars a; /html/land-speed/2009-02/msg00074.html (8,414 bytes)
3. Re: [Land-speed] rollcage welding (score: 1): Author: "Benn" <karhu@california.com>; Date: Thu, 26 Feb 2009 11:09:07 -0800; Thanks for the response, Dave. I don't think it'll be possible to get more than the main bar with some sleeve stubs removed from the car temporarily--any significant extensions just won't have enough; /html/land-speed/2009-02/msg00077.html (9,863 bytes)
4. Re: [Land-speed] rollcage welding (score: 1): Author: Joe Timney <joetimney@dol.net>; Date: Thu, 26 Feb 2009 15:58:35 -0500; It is not necessary to weld it all the way around the tube but you will need to gusset it. You can get about all but a 1/2 to 3/4 of an inch if you leave a 1/2 inch of side clearance by 'Hanging out; /html/land-speed/2009-02/msg00080.html (10,647 bytes)
5. Re: [Land-speed] rollcage welding (score: 1): Author: Bryan Savage <b.a.savage@wildblue.net>; Date: Thu, 26 Feb 2009 18:30:41 -0800; Buy a good 3" hole saw and get a Milwaukee 1/2" drill. Drill holes, save have welder stick the holes back before he's done. Screw the body, the cage is 100 times more valuable and important. Just my; /html/land-speed/2009-02/msg00082.html (8,205 bytes)
6. Re: [Land-speed] rollcage welding (score: 1): Author: David Dymaxion <david_dymaxion@yahoo.com>; Date: Fri, 27 Feb 2009 11:20:53 -0800 (PST); This might help (apologies if this has already been mentioned): o Cut holes in the floor o Drop the tubes done the holes, lowering things for working room o Weld things up o Raise the cage o Slide th; /html/land-speed/2009-02/msg00083.html (8,915 bytes)
7. Re: [Land-speed] rollcage welding (score: 1): Author: NT788@comcast.net; Date: Fri, 27 Feb 2009 19:36:59 +0000 (UTC); Cut off the bottom, weld the top, sleeve and re-weld the bottom piece. Jack This might help (apologies if this has already been mentioned): o Cut holes in the floor o Drop the tubes done the holes,; /html/land-speed/2009-02/msg00084.html (9,007 bytes)

Current List: 1 - 7
Page: [1]