triumphs
[Top] [All Lists]

Re: [TR] TR4A trunk hinge question

To: Dave Connitt <dconnitt@fuse.net>
Subject: Re: [TR] TR4A trunk hinge question
From: Robert Rochlin <rrochlin@comcast.net>
Date: Wed, 1 Dec 2021 12:41:42 -0500
Cc: Triumphs <Triumphs@autox.team.net>
Delivered-to: mharc@autox.team.net
Delivered-to: triumphs@autox.team.net
References: <AE2C209E-41E5-4E15-985B-8D86050F6D89@fuse.net>
Hi Dave
 As I remember, I was able to do the bulb replacement by removing the glove 
box.  If you need to replace the glove box the replacement from TRF fits 
perfectly as opposed to the Moss glove.box which was impossible to install.
Best, Bob

Sent from my iPhone

> On Dec 1, 2021, at 12:12 PM, Dave Connitt <dconnitt@fuse.net> wrote:
> 
> Thanks!
> JB Weld it is!
> Dave Connitt 
> 
> Sent from my iPhone
> 
>> On Dec 1, 2021, at 11:44 AM, Notakitcar <notakitcar@yahoo.com> wrote:
>> 
>> Agree, JB Weld will do the job.
>> Bill B
>> TS30800L
>> 
>> -----Original Message-----
>> From: Triumphs [mailto:triumphs-bounces@autox.team.net] On Behalf Of 
>> auprichard@uprichard.net
>> Sent: Wednesday, December 1, 2021 10:24 AM
>> To: 'Dave Connitt' <dconnitt@fuse.net>; 'Triumphs' <triumphs@autox.team.net>
>> Subject: Re: [TR] TR4A trunk hinge question
>> 
>> I have had this happen a few times.  I have not had success with Locktite, 
>> but JB weld has worked.
>> 
>> Andrew Uprichard
>> Jackson, Michigan
>> 
>> -----Original Message-----
>> From: Triumphs <triumphs-bounces@autox.team.net> On Behalf Of Dave Connitt
>> Sent: Wednesday, December 1, 2021 10:48 AM
>> To: Triumphs <triumphs@autox.team.net>
>> Subject: [TR] TR4A trunk hinge question
>> 
>> Hi all, 
>> Itâ??s been some time since I have posted on this list but here goes.
>> During the restoration of my TR4A, I had purchased a new set of hinges for 
>> the trunk which was about 10 years ago. 
>> After noticing one hinge coming apart I found that the short threaded stud 
>> one that hinge actually pulled itself out of the hinge.
>> Two questions:
>> 1. Is this a common failure mode?
>> 2. If I used red Locktite or JB Weld to secure the studs would they stay put?
>> Thanks,
>> Dave Connitt 
>> DavesTR4A.com
>> 
>> Sent from my iPhone
>> ** triumphs@autox.team.net **
>> 
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/pipermail/triumphs  http://www.team.net/archive
>> 
>> Unsubscribe/Manage: 
>> http://autox.team.net/mailman/options/triumphs/auprichard@uprichard.net
>> 
>> ** triumphs@autox.team.net **
>> 
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/pipermail/triumphs  http://www.team.net/archive
>> 
>> Unsubscribe/Manage: 
>> http://autox.team.net/mailman/options/triumphs/notakitcar@yahoo.com
>> 
> 
> ** triumphs@autox.team.net **
> 
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/triumphs  http://www.team.net/archive
> 
> Unsubscribe/Manage: 
> http://autox.team.net/mailman/options/triumphs/rrochlin@comcast.net

** triumphs@autox.team.net **

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/pipermail/triumphs  http://www.team.net/archive

Unsubscribe/Manage: 
http://autox.team.net/mailman/options/triumphs/mharc@autox.team.net
<Prev in Thread] Current Thread [Next in Thread>