This is a multi-part message in MIME format.
--===============7393497972991213610==
boundary="------------D8817E26D1C54FFD14E2323D"
Content-Language: en-US
This is a multi-part message in MIME format.
--------------D8817E26D1C54FFD14E2323D
Content-Transfer-Encoding: 8bit
?? you never crimp to a tinned (soldered) wire end. The crimp can
deform and will not hold.
for 'LBC's'Â flux wire end, crimp, then solder then heat shrink as
appropriate to give the joint some mechanical assist (and further
electrical isolation.
all this can be quite subjective. The ysay never rely on solder as the
electrical connection. It's only meant to retain the mechanical
connection of the electrical contact. point.
Yet on my UAVs, (and older RC cars) its quite common to only solder blob
the end of 14/16awg wires to the ckt board pads which pass 40+ amps
without melt-down of massive losses. The battery leads are 'wire in
connector pin cup' soldered and can see 200 amp sustained currents!
...can be a bit scary (relying on such a contact) when you've got $3K to
$20K worth of craft and cameras relying on that power connection.
So my own opinion (and experiences)Â dielectric grease the end of the
wire, insert in terminal and crimp. Don't smash it, .....and use two
strokes across the crimp (two dimples)
ptegler
On 1/8/2019 3:05 PM, TERRY SMITH wrote:
> Just for the sake of discussion, crimping has some sub-options. One,
> coat the terminal wire with dialetric first to make it corrosion
> resistant. Option two, tin the wire before crimping onto it, also to
> make it corrosion resistant. Like others, I prefer to solder the
> connector to the wire when I can.
>
>> On January 8, 2019 at 10:24 AM dave <dave@ranteer.com> wrote:
>>
>> I purchased a crimper from british wiring. Iâ??ve used it at least a
>> zillion times in the last decade. Tool is still in great shape and
>> 99% of my crimps are too.
>>
>> Canâ??t do bullet connectors â?? have to purchase a separate tool for
>> that. But Iâ??ve done rings, spades, and all sorts of other crimps
>>
>>
>> On Jan 7, 2019, at 1:23 PM, David Friedlander <forzion7@gmail.com
>>
>> Hey all ~
>>
>> Hope everyone enjoyed their holidays and were able to
>>
>> spend some quality time with loved ones....
>>
>> I've got a new wire harness for my TR3 in hand and was
>>
>> wondering your thoughts for those wires /not /using bullet
>>
>> connectors, (I'll likely use the bullet crimping tool from
>>
>> British Wire for that). So, for wires requiring spades, rings,
>>
>> etc. do you suggest soldering these terminals or is crimping
>>
>> a better choice? If crimping, what tool have others found to
>>
>> be reliable?
>>
>>
>> Thanks !!
>>
>> Dave Friedlander
>>
>> '74 TR6
>>
>> '59 TR3A
>>
>>
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/pipermail/triumphs
>> http://www.team.net/archive
>>
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/triumphs/wbeech@flash.net
>>
>
>> ** triumphs@autox.team.net **
>>
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/pipermail/triumphs
>> http://www.team.net/archive
>>
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/triumphs/terryrs@comcast.net
>
>
>
> ** triumphs@autox.team.net **
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/triumphs http://www.team.net/archive
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/triumphs/ptegler@verizon.net
--
Paul Tegler
ptegler@verizon.net www.teglerizer.com
--------------D8817E26D1C54FFD14E2323D
Content-Transfer-Encoding: 8bit
<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body text="#000000" bgcolor="#FFFFFF">
<p>?? you never crimp to a tinned (soldered) wire end. The crimp
can deform and will not hold.<br>
for 'LBC's'Â flux wire end, crimp, then solder then heat shrink as
appropriate to give the joint some mechanical assist (and further
electrical isolation.</p>
<p>all this can be quite subjective. The ysay never rely on solder
as the electrical connection. It's only meant to retain the
mechanical connection of the electrical contact. point.</p>
<p>Yet on my UAVs, (and older RC cars) its quite common to only
solder blob the end of 14/16awg wires to the ckt board pads which
pass 40+ amps without melt-down of massive losses. The battery
leads are 'wire in connector pin cup' soldered and can see 200 amp
sustained currents!</p>
<p>...can be a bit scary (relying on such a contact) when you've got
$3K to $20K worth of craft and cameras relying on that power
connection.</p>
<p>So my own opinion (and experiences)Â dielectric grease the end of
the wire, insert in terminal and crimp. Don't smash it, .....and
use two strokes across the crimp (two dimples)<br>
</p>
<p>ptegler<br>
</p>
<p><br>
</p>
<p>On 1/8/2019 3:05 PM, TERRY SMITH wrote:<br>
</p>
<blockquote type="cite"
cite="mid:446446839.862468.1546977919846@connect.xfinity.com">
<meta http-equiv="content-type" content="text/html; charset=UTF-8">
<meta charset="UTF-8">
<p style="font-size: 12pt; font-family: helvetica, arial,
sans-serif; color: rgb(51, 51, 51);">Just for the sake of
discussion, crimping has some sub-options. One, coat the
terminal wire with dialetric first to make it corrosion
resistant. Option two, tin the wire before crimping onto it,
also to make it corrosion resistant. Like others, I prefer to
solder the connector to the wire when I can. <br>
</p>
<blockquote type="cite">On January 8, 2019 at 10:24 AM dave
<a class="moz-txt-link-rfc2396E"
href="mailto:dave@ranteer.com";><dave@ranteer.com></a> wrote: <br>
<br>
<div class="ox-48987b9086-WordSection1">
<p class="ox-48987b9086-MsoNormal" style="margin-bottom:
12.0pt;">I purchased a crimper from british wiring. Iâ??ve
used it at least a zillion times in the last decade. Tool
is still in great shape and 99% of my crimps are too.</p>
<p class="ox-48987b9086-MsoNormal" style="margin-bottom:
12.0pt;">Canâ??t do bullet connectors â?? have to purchase a
separate tool for that. But Iâ??ve done rings, spades, and
all sorts of other crimps</p>
<p class="ox-48987b9086-MsoNormal" style="margin-bottom:
12.0pt;"><br>
On Jan 7, 2019, at 1:23 PM, David Friedlander <<a
href="mailto:forzion7@gmail.com";
moz-do-not-send="true">forzion7@gmail.com</a>>
wrote:</p>
<div>
<div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">Hey all ~ </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;"> Â </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">Hope everyone enjoyed their
holidays and were able to </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">spend some quality time with
loved ones.... </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;"> Â </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">I've got a new wire harness
for my TR3 in hand and was </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">wondering your thoughts for
those wires <em>not </em>using bullet </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">connectors, (I'll likely use
the bullet crimping tool from </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">British Wire for that). So,
for wires requiring spades, rings, </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">etc. do you suggest soldering
these terminals or is crimping </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">a better choice? If crimping,
what tool have others found to </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">be reliable? </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;"><br>
Thanks !! </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;"> Â </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">Dave Friedlander </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">'74 TR6 </span></p>
</div>
<div>
<p class="ox-48987b9086-MsoNormal"><span
style="font-size: 18.0pt; font-family: 'Comic Sans
MS'; color: #000099;">'59 TR3A </span></p>
</div>
</div>
</div>
<div>
<p class="ox-48987b9086-MsoNormal">** <a
href="mailto:triumphs@autox.team.net";
moz-do-not-send="true">triumphs@autox.team.net</a> **<br>
<br>
Donate: <a href="http://www.team.net/donate.html";
moz-do-not-send="true">http://www.team.net/donate.html</a><br>
Archive: <a href="http://www.team.net/pipermail/triumphs";
moz-do-not-send="true">http://www.team.net/pipermail/triumphs</a>
 <a href="http://www.team.net/archive";
moz-do-not-send="true">http://www.team.net/archive</a><br>
<br>
Unsubscribe/Manage: <a
href="http://autox.team.net/mailman/options/triumphs/wbeech@flash.net";
moz-do-not-send="true">http://autox.team.net/mailman/options/triumphs/wbeech@flash.net</a><br>
</p>
</div>
</div>
</blockquote>
<p style="font-size: 12pt; font-family:
helvetica,arial,sans-serif; color: #333333;"
class="default-style"><br>
 </p>
<blockquote type="cite">** <a class="moz-txt-link-abbreviated"
href="mailto:triumphs@autox.team.net";>triumphs@autox.team.net</a> ** <br>
<br>
Donate: <a class="moz-txt-link-freetext"
href="http://www.team.net/donate.html";>http://www.team.net/donate.html</a> <br>
Archive: <a class="moz-txt-link-freetext"
href="http://www.team.net/pipermail/triumphs";>http://www.team.net/pipermail/triumphs</a>
<a class="moz-txt-link-freetext"
href="http://www.team.net/archive";>http://www.team.net/archive</a> <br>
<br>
Unsubscribe/Manage:
<a class="moz-txt-link-freetext"
href="http://autox.team.net/mailman/options/triumphs/terryrs@comcast.net";>http://autox.team.net/mailman/options/triumphs/terryrs@comcast.net</a>
<br>
</blockquote>
<p style="font-size: 12pt; font-family:
helvetica,arial,sans-serif; color: #333333;"
class="default-style"><br>
 </p>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<pre class="moz-quote-pre" wrap="">** <a class="moz-txt-link-abbreviated"
href="mailto:triumphs@autox.team.net";>triumphs@autox.team.net</a> **
Archive: <a class="moz-txt-link-freetext"
href="http://www.team.net/pipermail/triumphs";>http://www.team.net/pipermail/triumphs</a>
<a class="moz-txt-link-freetext"
href="http://www.team.net/archive";>http://www.team.net/archive</a>
</pre>
</blockquote>
<pre class="moz-signature" cols="72">--
Paul Tegler
<a class="moz-txt-link-abbreviated"
href="mailto:ptegler@verizon.net";>ptegler@verizon.net</a> <a
class="moz-txt-link-abbreviated"
href="http://www.teglerizer.com";>www.teglerizer.com</a></pre>
</body>
</html>
--------------D8817E26D1C54FFD14E2323D--
--===============7393497972991213610==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
** triumphs@autox.team.net **
Archive: http://www.team.net/pipermail/triumphs http://www.team.net/archive
--===============7393497972991213610==--
|