In a message dated 4/22/00 7:26:38 AM Eastern Daylight Time,
jerryvv@worldnet.att.net writes:
> st
>
> I would like to submit my experiences with an Alternator conversion on a
TR4
> A. The first time I wired the conversion I followed the "modified Dan
> Masters instructions" and the ignition warning light did not work properly
> at all. I followed these instructions because it made more sense to me that
> the heavy Brown/yellow wire should connect to the "Bat" post on the
> alternator. I was wrong. Connect it just as Dan says and things work. I
> replaced the thin Brown/green wire with a heaver gauge wire from the "Bat"
> post to the regulator and solved the thin wire problem. I also wrote to Dan
> for clarification but never got a response so maybe if he would ring in on
> all of this the mystery can get solved if indeed there is one.
> Jerry Van Vl
With all the problems that we had this weekend with the alternator conversion
for a TR4a, it ended up being the connector that was purchased from the parts
store, I also contacted Dan Masters and he replied promptly..
Here is his response..
In a message dated 4/21/2000 3:46:54 PM Eastern Daylight Time, Z27407 writes:
>
> Hello Dan..
>
> Are the instructions at VTR for this procedure that you have posted
correct??
Paul,
Yes, and no. Yes, in that the instruction work as written. No, in that two of
the wires should be swapped from an increased capacity standpoint.
These instructions have been used by several people, with no problems.
However, I have revised them to change the wiring as stated above, but, for
some reason, VTR has not posted my corrections yet (I sent them to VTR over
18 months ago). I have attached the corrected version below.
Nevertheless, your alternator should work just fine with the current
instructions.
>
> I have followed them to the point and the alternator will not function
> properly..
What type of problems are you experiencing? I'll be happy to help you
resolve the problems if you'll describe your symptoms. In the meantime, I'll
draw up a wiring diagram for you and send it to you later today or tomorrow.
Dan
****************************************************************************
ELECTRICAL INSTRUCTIONS FOR REPLACING THE GENERATOR WITH A GM ALTERNATOR IN A
TR4A
METHOD ONE (Utilizing existing wiring):
-----------------------------
AT THE CONTROL BOX:
Look for the following wires:
Black: Remove and discard.
---------------------------------------------
Smaller Brown/Yellow:
Brown/Green: Disconnect and tie together, with an insulated
connector.
----------------------------------------------------------------------------
Larger Brown/Yellow:
Brown/White:
Brown/Blue (2): Using a large, solder type butt connector, connect
all 4 of these wires together, and insulate with heat shrink tubing. Be aware
- this connection carries ALL of the current for the car, so it must be a
good connection. You do not want a high resistance here. You may have to go
to an electrical supply house for this type connector, rather than an auto
supply store, to get one large enough to hold all 4 wires. Run two wires into
one end of the connector, and the other two into the other end.
------------------------------------------------------------------------------
------------------
Remove the control box and, please, save for a friend who is a purist!
AT THE OLD GENERATOR:
You will find two wires, Brown/Green and Brown/Yellow. Disconnect them from
the generator and leave in place. Remove and save the generator.
AT THE NEW ALTERNATOR:
On the side of the case, you will find two spade lugs recessed into the body.
The lugs are identified on the body of the alternator as 1 & 2. You will need
a plug (connector) for these. These plugs are readily available at an auto
supply store, usually in a package hanging on the pegboard display rack in
the electrical section, and usually identified as an alternator extension
connector, or something similar. If not, the counter man will know what you
are looking for. There will be two short wires already connected to the plug.
On the back of the case, you will find an insulated screw terminal.
Connect the Brown/Green wire to the plug wire going to the # 1 terminal,
using a butt connector, or splice, solder, and insulate with heat shrink
tubing. The plug is keyed, and will only go in one way. Connect the other
lead from the plug (#2) to the screw terminal on the back of the alternator
case, along with the larger Brown/Yellow lead from the original harness,
using ring terminals. Both the larger Brown/Yellow wire and the wire from
terminal #2 connect to the screw terminal.
Disconnect the ground lead from the battery before proceeding with any
electrical work, and,
of course, follow all the rules of proper wiring practices. I recomend using
solder connections, and covering them with heat shrink tubing, but crimp type
connectors will work quite well also. You will need butt connectors for
attaching to the plug wires, and a large ring connector for the screw
terminal. If you would prefer not to have splices, you can remove the
terminals, and the wire, from the plug. Using new terminals of the proper
type, connect directly to the existing wires, and insert the terminals into
the plug. New terminals can be purchased from British Wiring, (20449 Ithaca,
Olympia Fields, IL 60461, 708-481-9050) and The Wire Works (167 Keystone
Road, Chester, PA 19013, 800-292-1940), among others.
You are finished!
There are two things, however, to be aware of:
1) Triumph did funny things when they built these cars, so your car might not
match the configuration above, and it may well have been modified by a
previous owner.
2) You now have an alternator capable of more than twice the output of your
old generator, but the wiring capacity has not changed. If you add heavy
loads, driving lights, high power stereo, etc, you can exceed the capacity of
the wires. Also, If you let the battery discharge completely, the alternator
can possibly recharge with enough current to overload the wires. If your
battery is completely discharged, recharge it with a charger rather than push
starting the car and letting the alternator recharge it. If you must do this,
keep a close watch on the ammeter, checking for overcharging. Under all other
usages, the wiring should not present a problem. The main advantage of the
higher output is the ability to provide a higher charge rate at low RPM and
idle. The standard loads on the TR4A does not require a higher charge current
at normal engine speeds, so the alternator will not be called on to provide
enough current to overload the wires.
METHOD TWO (Upgraded wiring):
If you wish to upgrade the wiring to take advantage of the higher output, it
is really quite simple.
--------------------------------------------
AS ABOVE, EXCEPT:
Cut off both ends of the larger Brown/Yellow wire - at the old generator and
at the control box - as close to the wire harness wrapping as possible (or,
unwrap the harness, and remove the wire all-together).Connect the two
Brown/Blue and the Brown /White wires together at the control box.
Instead of connecting the larger Brown/Yellow wire to the new alternator, add
a new wire of at least 10 Ga (8 Ga preferred). Connect one end to the screw
terminal at the alternator, and the other end to the terminal on the starter
solenoid where the main cable from the battery and a Brown wire are now
connected. Leave the existing wires at the solenoid connected. Very carefully
route this new wire alongside the existing wiring harness, and use cable ties
liberally for support.
Now, the alternator can provide full charging current without worrying about
burning up the wiring.
There is one downside to this approach: The charge indicating light will work
as before, but the ammeter will only read discharge. It will register the
current being drawn by the various loads on the car, but will not indicate if
the alternator is charging.
If you wish to add extra loads, such as a high power sound system, connect
them directly to the battery, properly fused, of course. Loads connected
directly to the battery will not be indicated on the ammeter.
OPTIONS:
--------------------------
There are several other ways to do the replacement. For example, you may wish
to use a larger range ammeter, or you may wish to replace the ammeter with a
voltmeter. If so, contact me with your preferences, and I will try to provide
the appropriate instructions.
You may also choose to use a different alternator, rather than the GM unit.
If so, it will be wired very similarly to the above, only the connections at
the alternator itself will be different.
Dan Masters,
DANMAS@aol.com 7/6/98
|