Re: [Tigers] Steering rack

[Will Seay <Tigers@embarqmail.com>]

--===============8321327177308621356==

--000000000000d2f47105adb58340
Content-Transfer-Encoding: quoted-printable

The Tiger rack, according to the shop manual, holds 0.6 US pints.  That's
9.6 oz.

Will - 382001570
Tigers@embarqmail.com


On Mon, Aug 24, 2020 at 11:32 PM coolvt--- via Tigers <tigers@autox.team.ne=
t>
wrote:

> I find that the MG Midget rack that I use requires 8 oz. of oil.  I
> thought the Tiger rack was much more than that.
>
> In a message dated 8/24/2020 9:13:21 PM Eastern Standard Time,
> twotigers@verizon.net writes:
>
>
> I watched my rack bellows as I turned the wheel lock to lock- found the
> section of the bellow that flexed the least, poked a tiny hole through th=
e
> top of that bellow, filled the rack with a big hypodermic needle, then pu=
t
> a spot of butyl rubber on the pin hole. It=E2=80=99s been 20 years or so,=
 and it=E2=80=99s
> never leaked and the rubber is still sealed where I pricked it.  Kirk
>
>
>
> *From:* Tigers <tigers-bounces@autox.team.net> *On Behalf Of *coolvt---
> via Tigers
> *Sent:* Monday, August 24, 2020 5:46 PM
> *To:* tigers@autox.team.net
> *Subject:* [Tigers] Steering rack
>
>
>
> I've filled a few racks  over the years,but  always with the rack off the
> car. I'm thinking of trying with rack on the car this time. Anyone have a
> foolproof method of doing this?  Mark L
>
> In a message dated 8/24/2020 6:50:13 PM Eastern Standard Time,
> tigers@autox.team.net writes:
>
>
>
> Ditto's on the wanting something better than zip ties.
> I have seen a similar to the sardine clamp for the vacuum booster on Moss
> motors. It's close but no cigar. The stainless steel ones would look almo=
st
> too nice.
>
>
> ------------------------------
>
> On Monday, August 24, 2020 tigers-request <tigers@autox.team.net> wrote:
>
> Send Tigers mailing list submissions to
>
>     tigers@autox.team.net
>
>
>
> To subscribe or unsubscribe via the World Wide Web, visit
>
>     http://autox.team.net/mailman/listinfo/tigers
>
> or, via email, send a message with subject or body 'help' to
>
>     tigers-request@autox.team.net
>
>
>
> You can reach the person managing the list at
>
>     tigers-owner@autox.team.net
>
>
>
> When replying, please edit your Subject line so it is more specific
>
> than "Re: Contents of Tigers digest..."
>
>
>
>
>
> Today's Topics:
>
>
>
>   1. Re: Steering rack (Jay)
>
>   2. Re: Steering rack (steve wick)
>
>
>
>
>
> ----------------------------------------------------------------------
>
>
>
> Message: 1
>
> Date: Mon, 24 Aug 2020 14:34:00 -0700
>
> From: Jay <jay.laifman@gmail.com>
>
> To: Tom Witt <atwittsend@verizon.net>
>
> Cc: Tigers <tigers@autox.team.net>
>
> Subject: Re: [Tigers] Steering rack
>
> Message-ID: <0A9CFE40-AE38-481E-9F18-15C80B2B4CFF@gmail.com>
>
> Content-Type: text/plain; charset=3D"utf-8"
>
>
>
> Here are some options from McMaster Carr.  The first one is one of those
> squeeze bars types.  The other is 5/16? wide, which seems to be their mos=
t
> narrow.
>
>
>
> I know I?ve seen more narrow somewhere.
>
>
>
>
> https://www.mcmaster.com/hose-clamps/constant-tension-spring-clamps-for-f=
irm-hose-and-tube/
>
>
>
> https://www.mcmaster.com/hose-clamps/clamp-type~worm-drive/band-width~5-1=
6/
>
>
>
>
>
> On Aug 24, 2020, at 2:21 PM, Tom Witt via Tigers <tigers@autox.team.net>
> wrote:
>
>
>
> Wanting something better than plastic zip ties to secure the boots I
> ventures to the world of hose clamps. You are correct most are too wide. =
I
> scoured through Pick Your Part and found certain BMW clamps (left in imag=
e)
> from the 80's/90's to not only be narrow enough, but also have a slight
> bevel on the edge. That said it was still a search to find the clamp in a=
n
> appropriate diameter. I used these on my Tiger rack. I'd assume the midge=
t
> rack boots are similar. Sorry I can't tell you the year/model and locatio=
n
> the clamps were used but hopefully it helps with your search. Photo for
> comparison.
>
>
>
> <ichnfkdfppofgpgj.png>
>
>
>
>
>
>
>
> On 8/24/2020 6:42 AM, coolvt--- via Tigers wrote:
>
> >
>
> > I have the MG Midget steering rack conversion.?? I need rubber boots.??
> Does it take the same as a standard Tiger??? Also, what are good clamps
> that will work to secure??? Radiator clamps seem a little too wide and te=
nd
> to cut into the boot.?? ??Thanks, Mark L
>
> >
>
> >
>
> > _______________________________________________
>
> >
>
>
> >
>
> > Donate: http://www.team.net/donate.html <http://www.team.net/donate.htm=
l
> >
>
> > Archive: http://www.team.net/pipermail/tigers <
> http://www.team.net/pipermail/tigers> http://autox.team.net/archive <
> http://autox.team.net/archive>
>
> >
>
> > Unsubscribe: http://autox.team.net/mailman/options/tigers/atwittsend@ve=
rizon.net
> <http://autox.team.net/mailman/options/tigers/atwittsend@verizon.net>
>
> >
>
> >
>
> _______________________________________________
>
>
>
> tigers@autox.team.net
>
>
>
> Donate: http://www.team.net/donate.html
>
> Archive: http://www.team.net/pipermail/tigers
> http://autox.team.net/archive
>
>
>
> Unsubscribe:
> http://autox.team.net/mailman/options/tigers/jay.laifman@gmail.com
>
>
>
>
>
>
>
> -------------- next part --------------
>
> An HTML attachment was scrubbed...
>
> URL: <
> http://autox.team.net/pipermail/tigers/attachments/20200824/137dc75c/atta=
chment-0001.htm
> >
>
>
>
> ------------------------------
>
>
>
> Message: 2
>
> Date: Mon, 24 Aug 2020 22:27:22 +0000
>
> From: steve wick <srwick@hotmail.com>
>
> To: "tigers@autox.team.net" <tigers@autox.team.net>, Tom Witt
>
>     <atwittsend@verizon.net>
>
> Subject: Re: [Tigers] Steering rack
>
> Message-ID:
>
>     <
> BYAPR06MB4726688E29CA6213A9A1EEF1D8560@BYAPR06MB4726.namprd06.prod.outloo=
k.com
> >
>
>
>
> Content-Type: text/plain; charset=3D"iso-8859-1"
>
>
>
> What size do you need? A PEX clamp, available at plumbing/home supply
> stores may work, and is similar to what auto manufacturers use now.
>
>
>
> [cid:d5e737fc-a7bd-4c11-b175-ac3df52da3fb]
>
>
>
> This is from the McMaster-Carr catalog.
>
>
>
> [cid:02be576d-669c-40d6-9f65-5cc9ff9e0cb8]
>
>
>
>
>
> Steve
>
>
>
> ________________________________
>
> From: Tigers <tigers-bounces@autox.team.net> on behalf of Tom Witt via
> Tigers <tigers@autox.team.net>
>
> Sent: Monday, August 24, 2020 2:21 PM
>
> To: tigers@autox.team.net <tigers@autox.team.net>
>
> Subject: Re: [Tigers] Steering rack
>
>
>
>
>
> Wanting something better than plastic zip ties to secure the boots I
> ventures to the world of hose clamps. You are correct most are too wide. =
I
> scoured through Pick Your Part and found certain BMW clamps (left in imag=
e)
> from the 80's/90's to not only be narrow enough, but also have a slight
> bevel on the edge. That said it was still a search to find the clamp in a=
n
> appropriate diameter. I used these on my Tiger rack. I'd assume the midge=
t
> rack boots are similar. Sorry I can't tell you the year/model and locatio=
n
> the clamps were used but hopefully it helps with your search. Photo for
> comparison.
>
>
>
> [cid:part1.6A2F5674.9E614D0F@verizon.net]
>
>
>
>
>
> On 8/24/2020 6:42 AM, coolvt--- via Tigers wrote:
>
>
>
> I have the MG Midget steering rack conversion.?? I need rubber boots.??
> Does it take the same as a standard Tiger??? Also, what are good clamps
> that will work to secure??? Radiator clamps seem a little too wide and te=
nd
> to cut into the boot.?? ??Thanks, Mark L
>
>
>
>
>
>
>
> _______________________________________________
>
>
>
>
>
>
> Donate: http://www.team.net/donate.html
>
> Archive: http://www.team.net/pipermail/tigers
> http://autox.team.net/archive
>
>
>
> Unsubscribe:
> http://autox.team.net/mailman/options/tigers/atwittsend@verizon.net
>
>
>
>
>
>
>
> -------------- next part --------------
>
> An HTML attachment was scrubbed...
>
> URL: <
> http://autox.team.net/pipermail/tigers/attachments/20200824/b4265bb0/atta=
chment.htm
> >
>
> -------------- next part --------------
>
> A non-text attachment was scrubbed...
>
> Name: ichnfkdfppofgpgj.png
>
> Type: image/png
>
> Size: 1554373 bytes
>
> Desc: ichnfkdfppofgpgj.png
>
> URL: <
> http://autox.team.net/pipermail/tigers/attachments/20200824/b4265bb0/atta=
chment.png
> >
>
> -------------- next part --------------
>
> A non-text attachment was scrubbed...
>
> Name: image.png
>
> Type: image/png
>
> Size: 112678 bytes
>
> Desc: image.png
>
> URL: <
> http://autox.team.net/pipermail/tigers/attachments/20200824/b4265bb0/atta=
chment-0001.png
> >
>
> -------------- next part --------------
>
> A non-text attachment was scrubbed...
>
> Name: image.png
>
> Type: image/png
>
> Size: 73960 bytes
>
> Desc: image.png
>
> URL: <
> http://autox.team.net/pipermail/tigers/attachments/20200824/b4265bb0/atta=
chment-0002.png
> >
>
>
>
> ------------------------------
>
>
>
> Subject: Digest Footer
>
>
>
> _______________________________________________
>
> Tigers mailing list
>
> Tigers@autox.team.net
>
> http://autox.team.net/mailman/listinfo/tigers
>
>
>
> Donate: http://www.team.net/donate.html
>
> Archive: http://www.team.net/pipermail/tigers
> http://autox.team.net/archive
>
>
>
>
>
> ------------------------------
>
>
>
> End of Tigers Digest, Vol 13, Issue 188
>
> ***************************************
>
> _______________________________________________
>
> tigers@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/tigers
> http://autox.team.net/archive
>
> Unsubscribe: http://autox.team.net/mailman/options/tigers/coolvt@aol.com
>
> _______________________________________________
>
> tigers@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/pipermail/tigers
> http://autox.team.net/archive
>
> Unsubscribe:
> http://autox.team.net/mailman/options/tigers/tigers@embarqmail.com
>
>
>

--000000000000d2f47105adb58340
Content-Transfer-Encoding: quoted-printable

<div dir=3D"ltr"><div class=3D"gmail_default" style=3D"font-size:small">The=
 Tiger rack, according to the shop manual, holds 0.6 US pints.=C2=A0 That&#=
39;s 9.6 oz.</div><div class=3D"gmail_default" style=3D"font-size:small"><b=
r></div><div><div dir=3D"ltr" class=3D"gmail_signature" data-smartmail=3D"g=
mail_signature"><div dir=3D"ltr">Will - 382001570 <br><a href=3D"mailto:Tig=
ers@embarqmail.com" target=3D"_blank">Tigers@embarqmail.com</a></div></div>=
</div><br></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gm=
ail_attr">On Mon, Aug 24, 2020 at 11:32 PM coolvt--- via Tigers &lt;<a href=
=3D"mailto:tigers@autox.team.net";>tigers@autox.team.net</a>&gt; wrote:<br><=
/div><blockquote class=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;bo=
rder-left:1px solid rgb(204,204,204);padding-left:1ex"><div>
<div style=3D"font-family:arial,helvetica,sans-serif;font-size:12pt;color:r=
gb(0,0,0)">
<div><span style=3D"font-family:arial,helvetica,sans-serif;font-size:12pt;c=
olor:rgb(0,0,0)">I find that the MG Midget rack that I use requires 8 oz. o=
f oil.=C2=A0 I thought the Tiger rack was much more than that.<br><br></spa=
n></div>
</div>
In a message dated 8/24/2020 9:13:21 PM Eastern Standard Time, <a href=3D"m=
ailto:twotigers@verizon.net" target=3D"_blank">twotigers@verizon.net</a> wr=
ites:
<div>=C2=A0</div>
<div id=3D"gmail-m_-3272405742137805137yiv0050017594">
<div>
<div>
<p>I watched my rack bellows as I turned the wheel lock to lock- found the =
section of the bellow that flexed the least, poked a tiny hole through the =
top of that bellow, filled the rack with a big hypodermic needle, then put =
a spot of butyl rubber on the pin hole. It=E2=80=99s been 20 years or so, a=
nd it=E2=80=99s never leaked and the rubber is still sealed where I pricked=
 it.=C2=A0 Kirk</p>
<p>=C2=A0</p>
<div id=3D"gmail-m_-3272405742137805137yiv0050017594yqt33262">
<div style=3D"border-right:none;border-bottom:none;border-left:none;border-=
top:1pt solid rgb(225,225,225);padding:3pt 0in 0in">
<p><strong>From:</strong> Tigers &lt;<a href=3D"mailto:tigers-bounces@autox=
.team.net" target=3D"_blank">tigers-bounces@autox.team.net</a>&gt; <strong>=
On Behalf Of </strong>coolvt--- via Tigers<br clear=3D"none"><strong>Sent:<=
/strong> Monday, August 24, 2020 5:46 PM<br clear=3D"none"><strong>To:</str=
ong> <a href=3D"mailto:tigers@autox.team.net"; rel=3D"noopener noreferrer" t=
arget=3D"_blank">tigers@autox.team.net</a><br clear=3D"none"><strong>Subjec=
t:</strong> [Tigers] Steering rack</p>
</div>
<p>=C2=A0</p>
<div>
<div>
<div>
<p style=3D"margin-bottom:12pt"><span style=3D"font-size:12pt;font-family:s=
ans-serif;color:black">I&#39;ve filled a few racks=C2=A0 over the years,but=
=C2=A0 always with the rack off the car. I&#39;m thinking of trying with ra=
ck on the car this time. Anyone have a foolproof method of doing this?=C2=
=A0 Mark L</span></p>
</div>
</div>
<p>In a message dated 8/24/2020 6:50:13 PM Eastern Standard Time, <a href=
=3D"mailto:tigers@autox.team.net"; rel=3D"nofollow noopener" shape=3D"rect" =
target=3D"_blank">tigers@autox.team.net</a> writes:</p>
<div>
<p>=C2=A0</p>
</div>
<div id=3D"gmail-m_-3272405742137805137yiv0050017594">
<p>Ditto&#39;s on the wanting something better than zip ties. <br clear=3D"=
none">I have seen a similar to the sardine clamp for the vacuum booster on =
Moss motors. It&#39;s close but no cigar. The stainless steel ones would lo=
ok almost too nice.</p>
<div>
<p>=C2=A0</p>
</div>
<div style=3D"margin-bottom:6.75pt;text-align:center" align=3D"center"><hr =
style=3D"color:rgb(153,153,153)" align=3D"center" noshade size=3D"2" width=
=3D"100%"></div>
<p style=3D"margin-bottom:6.75pt"><span style=3D"font-size:10.5pt;color:rgb=
(153,153,153)">On Monday, August 24, 2020 tigers-request &lt;</span><span s=
tyle=3D"font-size:10.5pt;color:rgb(0,0,160)"><a href=3D"mailto:tigers@autox=
.team.net" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">tiger=
s@autox.team.net</a></span><span style=3D"font-size:10.5pt;color:rgb(153,15=
3,153)">&gt; wrote:</span></p>
<div>
<p style=3D"margin-bottom:6.75pt">Send Tigers mailing list submissions to</=
p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0=C2=A0=C2=A0 <a href=3D"mailto:tige=
rs@autox.team.net" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blan=
k">tigers@autox.team.net</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">To subscribe or unsubscribe via the World=
 Wide Web, visit</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0=C2=A0=C2=A0 <a href=3D"http://auto=
x.team.net/mailman/listinfo/tigers" rel=3D"nofollow noopener" shape=3D"rect=
" target=3D"_blank">http://autox.team.net/mailman/listinfo/tigers</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">or, via email, send a message with subjec=
t or body &#39;help&#39; to</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0=C2=A0=C2=A0 <a href=3D"mailto:tige=
rs-request@autox.team.net" rel=3D"nofollow noopener" shape=3D"rect" target=
=3D"_blank">tigers-request@autox.team.net</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">You can reach the person managing the lis=
t at</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0=C2=A0=C2=A0 <a href=3D"mailto:tige=
rs-owner@autox.team.net" rel=3D"nofollow noopener" shape=3D"rect" target=3D=
"_blank">tigers-owner@autox.team.net</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">When replying, please edit your Subject l=
ine so it is more specific</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">than &quot;Re: Contents of Tigers digest.=
..&quot;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Today&#39;s Topics:</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0 1. Re: Steering rack (Jay)</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0 2. Re: Steering rack (steve wick)<=
/p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">-----------------------------------------=
-----------------------------</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Message: 1</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Date: Mon, 24 Aug 2020 14:34:00 -0700</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">From: Jay &lt;<a href=3D"mailto:jay.laifm=
an@gmail.com" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">ja=
y.laifman@gmail.com</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">To: Tom Witt &lt;<a href=3D"mailto:atwitt=
send@verizon.net" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank=
">atwittsend@verizon.net</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Cc: Tigers &lt;<a href=3D"mailto:tigers@a=
utox.team.net" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">t=
igers@autox.team.net</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Subject: Re: [Tigers] Steering rack</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Message-ID: &lt;<a href=3D"mailto:0A9CFE4=
0-AE38-481E-9F18-15C80B2B4CFF@gmail.com" rel=3D"nofollow noopener" shape=3D=
"rect" target=3D"_blank">0A9CFE40-AE38-481E-9F18-15C80B2B4CFF@gmail.com</a>=
&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Content-Type: text/plain; charset=3D&quot=
;utf-8&quot;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Here are some options from McMaster Carr.=
=C2=A0 The first one is one of those squeeze bars types.=C2=A0 The other is=
 5/16? wide, which seems to be their most narrow.</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">I know I?ve seen more narrow somewhere.</=
p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt"><a href=3D"https://www.mcmaster.com/hose-=
clamps/constant-tension-spring-clamps-for-firm-hose-and-tube/" rel=3D"nofol=
low noopener" shape=3D"rect" target=3D"_blank">https://www.mcmaster.com/hos=
e-clamps/constant-tension-spring-clamps-for-firm-hose-and-tube/</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt"><a href=3D"https://www.mcmaster.com/hose-=
clamps/clamp-type~worm-drive/band-width~5-16/" rel=3D"nofollow noopener" sh=
ape=3D"rect" target=3D"_blank">https://www.mcmaster.com/hose-clamps/clamp-t=
ype~worm-drive/band-width~5-16/</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">On Aug 24, 2020, at 2:21 PM, Tom Witt via=
 Tigers &lt;<a href=3D"mailto:tigers@autox.team.net"; rel=3D"nofollow noopen=
er" shape=3D"rect" target=3D"_blank">tigers@autox.team.net</a>&gt; wrote:</=
p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Wanting something better than plastic zip=
 ties to secure the boots I ventures to the world of hose clamps. You are c=
orrect most are too wide. I scoured through Pick Your Part and found certai=
n BMW clamps (left in image) from the 80&#39;s/90&#39;s to not only be narr=
ow enough, but also have a slight bevel on the edge. That said it was still=
 a search to find the clamp in an appropriate diameter. I used these on my =
Tiger rack. I&#39;d assume the midget rack boots are similar. Sorry I can&#=
39;t tell you the year/model and location the clamps were used but hopefull=
y it helps with your search. Photo for comparison.</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&lt;ichnfkdfppofgpgj.png&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">On 8/24/2020 6:42 AM, coolvt--- via Tiger=
s wrote:</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt; I have the MG Midget steering rack c=
onversion.?? I need rubber boots.?? Does it take the same as a standard Tig=
er??? Also, what are good clamps that will work to secure??? Radiator clamp=
s seem a little too wide and tend to cut into the boot.?? ??Thanks, Mark L<=
/p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt; ____________________________________=
___________</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt; <a href=3D"mailto:tigers@autox.team.=
net" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">tigers@auto=
x.team.net</a> &lt;mailto:<a href=3D"mailto:tigers@autox.team.net"; rel=3D"n=
ofollow noopener" shape=3D"rect" target=3D"_blank">tigers@autox.team.net</a=
>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt; Donate: <a href=3D"http://www.team.n=
et/donate.html" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">=
te.html" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">http://=
www.team.net/donate.html</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt; Archive: <a href=3D"http://www.team.=
net/pipermail/tigers" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_b=
lank">http://www.team.net/pipermail/tigers </a>&lt;<a href=3D"http://www.te=
am.net/pipermail/tigers" rel=3D"nofollow noopener" shape=3D"rect" target=3D=
"_blank">http://www.team.net/pipermail/tigers</a>&gt; <a href=3D"http://aut=
ox.team.net/archive" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_bl=
ank">http://autox.team.net/archive </a>&lt;<a href=3D"http://autox.team.net=
/archive" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">http:/=
/autox.team.net/archive</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt; Unsubscribe: <a href=3D"http://autox=
.team.net/mailman/options/tigers/atwittsend@verizon.net" rel=3D"nofollow no=
opener" shape=3D"rect" target=3D"_blank">http://autox.team.net/mailman/opti=
ons/tigers/atwittsend@verizon.net </a>&lt;<a href=3D"http://autox.team.net/=
mailman/options/tigers/atwittsend@verizon.net" rel=3D"nofollow noopener" sh=
ape=3D"rect" target=3D"_blank">http://autox.team.net/mailman/options/tigers=
/atwittsend@verizon.net</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">_________________________________________=
______</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt"><a href=3D"mailto:tigers@autox.team.net"; =
rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">tigers@autox.tea=
m.net</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Donate: <a href=3D"http://www.team.net/do=
nate.html" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">http:=
//www.team.net/donate.html</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Archive: <a href=3D"http://www.team.net/p=
ipermail/tigers" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank"=
>http://www.team.net/pipermail/tigers </a><a href=3D"http://autox.team.net/=
archive" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">http://=
autox.team.net/archive</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Unsubscribe: <a href=3D"http://autox.team=
.net/mailman/options/tigers/jay.laifman@gmail.com" rel=3D"nofollow noopener=
" shape=3D"rect" target=3D"_blank">http://autox.team.net/mailman/options/ti=
gers/jay.laifman@gmail.com</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">-------------- next part --------------</=
p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">An HTML attachment was scrubbed...</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">URL: &lt;<a href=3D"http://autox.team.net=
/pipermail/tigers/attachments/20200824/137dc75c/attachment-0001.htm" rel=3D=
"nofollow noopener" shape=3D"rect" target=3D"_blank">http://autox.team.net/=
pipermail/tigers/attachments/20200824/137dc75c/attachment-0001.htm</a>&gt;<=
/p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">------------------------------</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Message: 2</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Date: Mon, 24 Aug 2020 22:27:22 +0000</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">From: steve wick &lt;<a href=3D"mailto:sr=
wick@hotmail.com" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank=
">srwick@hotmail.com</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">To: &quot;<a href=3D"mailto:tigers@autox.=
team.net" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">tigers=
@autox.team.net</a>&quot; &lt;<a href=3D"mailto:tigers@autox.team.net"; rel=
=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">tigers@autox.team.n=
et</a>&gt;, Tom Witt</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0=C2=A0=C2=A0 &lt;<a href=3D"mailto:=
atwittsend@verizon.net" rel=3D"nofollow noopener" shape=3D"rect" target=3D"=
_blank">atwittsend@verizon.net</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Subject: Re: [Tigers] Steering rack</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Message-ID:</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0=C2=A0=C2=A0 &lt;<a href=3D"mailto:=
BYAPR06MB4726688E29CA6213A9A1EEF1D8560@BYAPR06MB4726.namprd06.prod.outlook.=
com" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">BYAPR06MB47=
26688E29CA6213A9A1EEF1D8560@BYAPR06MB4726.namprd06.prod.outlook.com</a>&gt;=
</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0=C2=A0=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Content-Type: text/plain; charset=3D&quot=
;iso-8859-1&quot;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">What size do you need? A PEX clamp, avail=
able at plumbing/home supply stores may work, and is similar to what auto m=
anufacturers use now.</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">[cid:d5e737fc-a7bd-4c11-b175-ac3df52da3fb=
]</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">This is from the McMaster-Carr catalog.</=
p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">[cid:02be576d-669c-40d6-9f65-5cc9ff9e0cb8=
]</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Steve</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">________________________________</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">From: Tigers &lt;<a href=3D"mailto:tigers=
-bounces@autox.team.net" rel=3D"nofollow noopener" shape=3D"rect" target=3D=
"_blank">tigers-bounces@autox.team.net</a>&gt; on behalf of Tom Witt via Ti=
gers &lt;<a href=3D"mailto:tigers@autox.team.net"; rel=3D"nofollow noopener"=
 shape=3D"rect" target=3D"_blank">tigers@autox.team.net</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Sent: Monday, August 24, 2020 2:21 PM</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">To: <a href=3D"mailto:tigers@autox.team.n=
et" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">tigers@autox=
.team.net</a> &lt;<a href=3D"mailto:tigers@autox.team.net"; rel=3D"nofollow =
noopener" shape=3D"rect" target=3D"_blank">tigers@autox.team.net</a>&gt;</p=
>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Subject: Re: [Tigers] Steering rack</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Wanting something better than plastic zip=
 ties to secure the boots I ventures to the world of hose clamps. You are c=
orrect most are too wide. I scoured through Pick Your Part and found certai=
n BMW clamps (left in image) from the 80&#39;s/90&#39;s to not only be narr=
ow enough, but also have a slight bevel on the edge. That said it was still=
 a search to find the clamp in an appropriate diameter. I used these on my =
Tiger rack. I&#39;d assume the midget rack boots are similar. Sorry I can&#=
39;t tell you the year/model and location the clamps were used but hopefull=
y it helps with your search. Photo for comparison.</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">[cid:<a href=3D"mailto:part1.6A2F5674.9E6=
14D0F@verizon.net" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blan=
k">part1.6A2F5674.9E614D0F@verizon.net</a>]</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">On 8/24/2020 6:42 AM, coolvt--- via Tiger=
s wrote:</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">I have the MG Midget steering rack conver=
sion.?? I need rubber boots.?? Does it take the same as a standard Tiger???=
 Also, what are good clamps that will work to secure??? Radiator clamps see=
m a little too wide and tend to cut into the boot.?? ??Thanks, Mark L</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">_________________________________________=
______</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt"><a href=3D"mailto:tigers@autox.team.net"; =
rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">tigers@autox.tea=
m.net</a>&lt;mailto:<a href=3D"mailto:tigers@autox.team.net"; rel=3D"nofollo=
w noopener" shape=3D"rect" target=3D"_blank">tigers@autox.team.net</a>&gt;<=
/p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Donate: <a href=3D"http://www.team.net/do=
nate.html" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">http:=
//www.team.net/donate.html</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Archive: <a href=3D"http://www.team.net/p=
ipermail/tigers" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank"=
>http://www.team.net/pipermail/tigers </a><a href=3D"http://autox.team.net/=
archive" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">http://=
autox.team.net/archive</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Unsubscribe: <a href=3D"http://autox.team=
.net/mailman/options/tigers/atwittsend@verizon.net" rel=3D"nofollow noopene=
r" shape=3D"rect" target=3D"_blank">http://autox.team.net/mailman/options/t=
igers/atwittsend@verizon.net</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">-------------- next part --------------</=
p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">An HTML attachment was scrubbed...</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">URL: &lt;<a href=3D"http://autox.team.net=
/pipermail/tigers/attachments/20200824/b4265bb0/attachment.htm" rel=3D"nofo=
llow noopener" shape=3D"rect" target=3D"_blank">http://autox.team.net/piper=
mail/tigers/attachments/20200824/b4265bb0/attachment.htm</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">-------------- next part --------------</=
p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">A non-text attachment was scrubbed...</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Name: ichnfkdfppofgpgj.png</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Type: image/png</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Size: 1554373 bytes</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Desc: ichnfkdfppofgpgj.png</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">URL: &lt;<a href=3D"http://autox.team.net=
/pipermail/tigers/attachments/20200824/b4265bb0/attachment.png" rel=3D"nofo=
llow noopener" shape=3D"rect" target=3D"_blank">http://autox.team.net/piper=
mail/tigers/attachments/20200824/b4265bb0/attachment.png</a>&gt;</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">-------------- next part --------------</=
p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">A non-text attachment was scrubbed...</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Name: image.png</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Type: image/png</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Size: 112678 bytes</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Desc: image.png</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">URL: &lt;<a href=3D"http://autox.team.net=
/pipermail/tigers/attachments/20200824/b4265bb0/attachment-0001.png" rel=3D=
"nofollow noopener" shape=3D"rect" target=3D"_blank">http://autox.team.net/=
pipermail/tigers/attachments/20200824/b4265bb0/attachment-0001.png</a>&gt;<=
/p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">-------------- next part --------------</=
p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">A non-text attachment was scrubbed...</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Name: image.png</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Type: image/png</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Size: 73960 bytes</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Desc: image.png</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">URL: &lt;<a href=3D"http://autox.team.net=
/pipermail/tigers/attachments/20200824/b4265bb0/attachment-0002.png" rel=3D=
"nofollow noopener" shape=3D"rect" target=3D"_blank">http://autox.team.net/=
pipermail/tigers/attachments/20200824/b4265bb0/attachment-0002.png</a>&gt;<=
/p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">------------------------------</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Subject: Digest Footer</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">_________________________________________=
______</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Tigers mailing list</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt"><a href=3D"mailto:Tigers@autox.team.net"; =
rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">Tigers@autox.tea=
m.net</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt"><a href=3D"http://autox.team.net/mailman/=
listinfo/tigers" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank"=
>http://autox.team.net/mailman/listinfo/tigers</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Donate: <a href=3D"http://www.team.net/do=
nate.html" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">http:=
//www.team.net/donate.html</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">Archive: <a href=3D"http://www.team.net/p=
ipermail/tigers" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank"=
>http://www.team.net/pipermail/tigers </a><a href=3D"http://autox.team.net/=
archive" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">http://=
autox.team.net/archive</a></p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">------------------------------</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">=C2=A0</p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">End of Tigers Digest, Vol 13, Issue 188</=
p>
</div>
<div>
<p style=3D"margin-bottom:6.75pt">***************************************</=
p>
</div>
</div>
<p style=3D"margin-bottom:12pt">___________________________________________=
____<br clear=3D"none"><br clear=3D"none"><a href=3D"mailto:tigers@autox.te=
am.net" rel=3D"nofollow noopener" shape=3D"rect" target=3D"_blank">tigers@a=
utox.team.net</a><br clear=3D"none"><br clear=3D"none">Donate: <a href=3D"h=
ttp://www.team.net/donate.html" rel=3D"nofollow noopener" shape=3D"rect" ta=
rget=3D"_blank">http://www.team.net/donate.html</a><br clear=3D"none">Archi=
ve: <a href=3D"http://www.team.net/pipermail/tigers"; rel=3D"nofollow noopen=
er" shape=3D"rect" target=3D"_blank">http://www.team.net/pipermail/tigers <=
/a><a href=3D"http://autox.team.net/archive"; rel=3D"nofollow noopener" shap=
e=3D"rect" target=3D"_blank">http://autox.team.net/archive</a><br clear=3D"=
none"><br clear=3D"none">Unsubscribe: <a href=3D"http://autox.team.net/mail=
man/options/tigers/coolvt@aol.com" rel=3D"nofollow noopener" shape=3D"rect"=
 target=3D"_blank">http://autox.team.net/mailman/options/tigers/coolvt@aol.=
com</a><br clear=3D"none"><br clear=3D"none"></p>
</div>
</div>
</div>
</div>
</div>
</div>_______________________________________________<br>
<br>
<a href=3D"mailto:tigers@autox.team.net"; target=3D"_blank">tigers@autox.tea=
m.net</a><br>
<br>
et=3D"_blank">http://www.team.net/donate.html</a><br>
Archive: <a href=3D"http://www.team.net/pipermail/tigers"; rel=3D"noreferrer=
" target=3D"_blank">http://www.team.net/pipermail/tigers</a> <a href=3D"htt=
p://autox.team.net/archive" rel=3D"noreferrer" target=3D"_blank">http://aut=
ox.team.net/archive</a><br>
<br>
Unsubscribe: <a href=3D"http://autox.team.net/mailman/options/tigers/tigers=
@embarqmail.com" rel=3D"noreferrer" target=3D"_blank">http://autox.team.net=
/mailman/options/tigers/tigers@embarqmail.com</a><br>
<br>
<br>
</blockquote></div>

--000000000000d2f47105adb58340--

--===============8321327177308621356==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________

tigers@autox.team.net

Archive: http://www.team.net/pipermail/tigers http://autox.team.net/archive

Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net



--===============8321327177308621356==--