Re: [Spridgets] just a double check.....

[Kevin Valentine via Spridgets <spridgets@autox.team.net>]

--===============0754777455238647229==

--0000000000006b5c86061dd6ce80
Content-Transfer-Encoding: quoted-printable

Mark,

Yes, the ends where the bolts go thru the clamp are supposed to be flush
with the block and the center section of the clamp where the dizzy goes
thru is slightly raised.

Kevin V.
Tuscarora, Pa

On Mon, Jul 22, 2024 at 9:17=E2=80=AFAM Mark Haynes via Spridgets <
spridgets@autox.team.net> wrote:

> I still need to turn my dizzy clamp plate around so that the clamp bolt i=
s
> on top and visible, so I thought that I'd check that since the end sectio=
ns
> where its bolted to the block are not planar to the clamp portion, that
> they are to be assembled flush to the block and the clamp portionis raise=
d.
> This is how I have it assembled, just a check that it should be this way
> and I'm not reducing the the engagement with the drive gear.
> Thanks, still looking for the no-start cause,
> Mark Haynes
> It only goes one way- Pay It Forward
> ------------------------
>
> spridgets@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Suggested annual donation: $12.75
>
> Archive: http://www.team.net/pipermail/spridgets
> http://autox.team.net/archive
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/spridgets/kevinv1275@gmail.com
>

--0000000000006b5c86061dd6ce80
Content-Transfer-Encoding: quoted-printable

<div dir=3D"ltr">Mark,<div><br></div><div>Yes, the ends where the bolts go =
thru the clamp are supposed to be flush with the block and the center secti=
on of the clamp where the dizzy goes thru is slightly raised.</div><div><br=
></div><div>Kevin V.</div><div>Tuscarora, Pa</div></div><br><div class=3D"g=
mail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Mon, Jul 22, 2024 at 9=
:17=E2=80=AFAM Mark Haynes via Spridgets &lt;<a href=3D"mailto:spridgets@au=
tox.team.net">spridgets@autox.team.net</a>&gt; wrote:<br></div><blockquote =
class=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;border-left:1px sol=
id rgb(204,204,204);padding-left:1ex"><div dir=3D"ltr"><div>I still need to=
 turn my dizzy clamp plate around so that the clamp bolt is on top and visi=
ble, so I thought that I&#39;d check that since the end sections where its =
bolted to the block are not planar to the clamp portion, that they are to b=
e assembled flush to the block and the clamp portionis raised. This is how =
I have it assembled, just a check that it should be this way and I&#39;m no=
t reducing the the engagement with the drive gear.</div><div>Thanks, still =
looking for the no-start cause,<br></div><div><div><div dir=3D"ltr" class=
=3D"gmail_signature"><div dir=3D"ltr"><div>Mark Haynes<br></div>It only goe=
s one way- Pay It Forward<br></div></div></div></div></div>
------------------------<br>
<br>
<a href=3D"mailto:spridgets@autox.team.net"; target=3D"_blank">spridgets@aut=
ox.team.net</a><br>
<br>
et=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/spridgets"; rel=3D"norefer=
rer" target=3D"_blank">http://www.team.net/pipermail/spridgets</a>=C2=A0 <a=
 href=3D"http://autox.team.net/archive"; rel=3D"noreferrer" target=3D"_blank=
">http://autox.team.net/archive</a><br>
<br>
ets/kevinv1275@gmail.com" rel=3D"noreferrer" target=3D"_blank">http://autox=
.team.net/mailman/options/spridgets/kevinv1275@gmail.com</a><br>
</blockquote></div>

--0000000000006b5c86061dd6ce80--

--===============0754777455238647229==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

------------------------

spridgets@autox.team.net


Archive: http://www.team.net/pipermail/spridgets  http://autox.team.net/archive


--===============0754777455238647229==--