you can buy a set at chevy of the forties for 20 bucks 1/4 drive 5 bits
Bill 53-3600 hot rod (project again)
Channahon,Ill.
website
www.hotrodstogo.com
Go ahead and take risks....just be sure that everything
will turn out OK.
----- Original Message -----
From: Deve Krehbiel <dkrehbiel@kscable.com>
To: <oletrucks@autox.team.net>
Sent: Monday, January 29, 2001 9:14 AM
Subject: [oletrucks] Clutch Head Driver Assistance Needed
> Below is a conversation I had with the SnapOn Representative. They have
two
> types of clutch head drivers.. the standard and then the 'G' type. I am
not
> sure which one is right for our application (working on the 47-54 Chevy
> Pickups). Can anyone shed some light on this? They have pictures at
> www.snapon.com but they are not clear.
>
> Thanks!
>
> Deve
>
> ---------------------
>
> Deve, I am not sure which one will suit that application.
> I will try to describe the design to you.
> The Clutch "A" type ( Exmp: SDM242 ) is more flat on the outside and bows
> out
> in the middle : -<>- <-- ( looks somewhat like this )
> Where as the "G" Model is more like a bow tie ( Exmp: SDM242G ) >-<
This
> is the best I can describe this to you. I wish I could have been more
help.
> Thank you...
>
> -----Original Message-----
> From: Deve Krehbiel [mailto:dkrehbiel@kscable.com]
> Sent: Monday, January 29, 2001 10:22 AM
> To: Beazley, Brian A.
> Subject: Re: Clutch Head solutions
>
>
>
> Yes I know you have clutch head drivers, but I since the pictures are not
> clear, I need to know the difference between the standard clutch and the
> 'G'. I am restoring several 1950 Chevy Pickups and need the ones that are
> used for that. Hopefully you can tell me which ones I need since the
> pictures arent real clear on the pattern of the clutch head.
>
> Thanks!!
>
> Deve
>
> ----- Original Message -----
> From: "Beazley, Brian A." <brian.a.beazley@snapon.com>
> Cc: <dkrehbiel@kscable.com>
> Sent: Monday, January 29, 2001 9:24 AM
> Subject: RE: Clutch Head solutions
>
>
>
> Good morning Deve, We do offer several Clutch Head bits.
> The part numbers range from SDM242 through SDM247 and SDM242G through
> SDM246G. If you click on the link listed below my name, you will enter the
> catalog where these items may be viewed. Thank you, please let me know if
> you have any other questions.
> Brian Beazley
> E-commerce Customer Service
> Snap-on Tools
> Midwest Regional Center
> 877-762-7662 Ext: 6637
> <mailto:brian.a.beazley@snapon.com>
> <http://www.snapon.com>
>
>
>
>
> -----Original Message-----
> From: Deve Krehbiel [mailto:dkrehbiel@kscable.com]
> Sent: Thursday, January 18, 2001 10:07
> To: questions@snapon.com
> Subject: Clutch Head solutions
>
>
>
> I am working on old 1948, 49, and 50 Chevy Pickups and they use a clutch
> head screw in about 3 or 4 sizes. I am told you have these in sockets,
bits
> and screwdrivers. I would like to see what you have and then probably
place
> an order.
>
> Deve Krehbiel
> oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
|