All,
I have a good manifold combo off a 55 235 engine that was on a 3/4 ton. I need
a good 50 216 manifold combo SN 3835497 or appropriate, to make my ole truck
happy. And my wife f... since running your truck in the garage without a
muffler is "way" too much excitement for some! :)
Glad to swap . Only cost will end up being to UPS, etc.
Gary Radicic
1950 Chev 3604
Geneseo, IL
-----Original Message-----
From: Jack Halton [mailto:safesix@earthlink.net]
Sent: Wednesday, August 09, 2000 12:30 PM
To: mike; oletrucks@autox.team.net
Subject: Re: [oletrucks] Ways to guess/rule out engine sizes?
Mike,
The best way is by casting number. www.inliners.org has a pretty good
list, with links to several others (you sorta have to hover the mouse around
this page as the links aren't too clear). I have never failed to get a hit
on at least one of these listings, except on Canadian models. The listing at
www.inliners.org/becks/ also provides ID by engine number prefix, so there
is an alternate way to identify the engine, in case the casting number can't
be easily found.
There was an optional 235 for heavy trucks in '48. It was called the
"Victory Six" or "Hi-Torque" 235 and looks just like a 216. I know of at
least one confirmed instance where this engine was installed in a new 1/2
ton as a dealer upgrade. It was a dipper-crank oil slinger like the 216 of
the same era, introduced in 1941, first with babbit mains, upgraded to
inserts in 1948. All of these older type 235's used babbit rods. Very tough
old workhorse engines, they were often the basis for the Wayne 12-Port
racing engines of the late '40s. They differ in both bore and stroke from
the 216.
I have some early Inliners tech stuff that has some more detailed ID
methods, but you should be able to nail down your engine from the above
references. If not, let me know whatever numbers you come up with, and we'll
go from there.
Regards,
Jack Halton
51 GMC 1/2 ton
Winter Park FL
----- Original Message -----
From: "mike" <m1a20@iname.com>
To: <oletrucks@autox.team.net>
Sent: Wednesday, August 09, 2000 11:52 AM
Subject: [oletrucks] Ways to guess/rule out engine sizes?
> I have seen a few threads about how to find out what displacement your
> engine is, but are there any characteristic features that distinguish the
> 216 from say 235 or 261? I was at a show last weekend, and saw a truck,
> hood open, and the motor in it just seemed much smaller (physically) than
> mine. I have tried to clean up the casting numbers, but as of yet have
not
> yet found the numbers I think I am reading on any of the web pages
regarding
> casting numbers. at the moment I do not have the numbers on me, but I can
> find them again later.
>
> the truck is a 1948 1-Ton, but probably doesn't have the original motor if
> it is not a 216. was there an optional motor size in '48? It was a
> tow/wrecker at one time for AAA if that would make a difference. anyhow,
as
> always, your comments and helps are greatly appreciated.
>
> if this is something I could know by just RTFM (reading the freaking
manual)
> let me know that also. so far I have not found this info on my own.
>
> the truck is basically in storage (garaged), but I am trying to learn
enough
> for when I do get chances work on it (irregularly at this point) I can
> actually get something done. Thanks again for any help.
>
>
>
>
>
> oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
>
oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
|