mg-t
[Top] [All Lists]

Re: [Mg-t] TD Engine Pull

To: Ron Olds <rolds@plausa.com>, wbeech@flash.net <wbeech@flash.net>, mg-t@autox.team.net <mg-t@autox.team.net>
Subject: Re: [Mg-t] TD Engine Pull
From: "lawrie" <lawrie@britcars.com>
Date: Sun, 15 Sep 2013 05:52:13 -0800
Delivered-to: mharc@autox.team.net
Delivered-to: mg-t@autox.team.net
References: <D41EE0DF20A47D48BF555A3204A3B9E5920BD482@MSERVER.PLASSERUSA.com>
With difficulty, Ron, (you have to beat it backwards with a heavy plastic 
hammer to get the drive pins free of the crank flange), but remember you also 
have to remove the oil pan. 

Lawrie 

>  -------Original Message-------
>  From: Ron Olds <rolds@plausa.com>
>  To: wbeech@flash.net <wbeech@flash.net>, mg-t@autox.team.net 
> <mg-t@autox.team.net>
>  Subject: Re: [Mg-t] TD Engine Pull
>  Sent: 15 Sep '13 03:05
>  
>  I have a small leak from my engine as well after rebuilding and installing 
> the
>  Moss seal.  I have not disassembled anything to see where the drip is coming
>  from.  Can someone tell me if the flywheel can be removed with the crankshaft
>  installed?
>  
>  Ronald Olds
>  Sales Manager
>  Plasser American Corporation
>  PO Box 5464
>  2001 Myers Road
>  Chesapeake, VA 23324-0464
>  
>  Phone  (757) 543-3526
>  Cell      (630) 240-0818
>  Fax      (757) 494-7186
>  
>  The information contained in this e-mail including any attachments may be
>  proprietary, privileged or confidential and is intended solely for the use of
>  the addressee. Any unauthorized distribution, disclosure or any other such 
> use
>  is strictly prohibited. Furthermore, any reviews, dissemination or copying by
>  anyone other than the intended recipient is expressly prohibited. If you have
>  received this e-mail in error, please notify the sender and destroy all 
> copies
>  of the original transmittal.
>  
>  -----Original Message-----
>  From: mg-t-bounces@autox.team.net [mailto:mg-t-bounces@autox.team.net] On
>  Behalf Of wbeech@flash.net
>  Sent: Thursday, September 12, 2013 4:34 PM
>  To: mg-t@autox.team.net
>  Subject: Re: [Mg-t] TD Engine Pull
>  
>  Finally getting around to the long-overdue task for replacing the rear main 
> on
>  the '52TD.  What is the consensus of the list as far as the best remedy for
>  this repair/replacement?  I would rather not have to grind the crank to fit
>  some aftermarket product.  Just going to do the seals and the top-end is 
> tight
>  and there are no other real issues here.
>  
>  Also, as this is my first MGT engine job where is the best resource, on-line,
>  to go to for soup-to-nuts guidance?
>  
>  Many thanks,
>  Bill
>  ______________________________________________
>  
>  Mg-t@autox.team.net
>  Donate: http://www.team.net/donate.html
>  Suggested annual donation  $11.47
>  Archive: http://www.team.net/archive
>  Forums: http://www.team.net/forums
>  Unsubscribe/Manage:
>  http://autox.team.net/mailman/options/mg-t/rolds@plausa.com
>  ______________________________________________
>  
>  Mg-t@autox.team.net
>  Donate: http://www.team.net/donate.html
>  Suggested annual donation  $11.47
>  Archive: http://www.team.net/archive
>  Forums: http://www.team.net/forums
>  Unsubscribe/Manage: 
> http://autox.team.net/mailman/options/mg-t/lawrie@britcars.com
______________________________________________

Mg-t@autox.team.net
Archive: http://www.team.net/archive

<Prev in Thread] Current Thread [Next in Thread>
  • Re: [Mg-t] TD Engine Pull, lawrie <=