Although a straight edge seems to show the surfaces to be flat, after the
7th attempt using various techniques and sealants and gaskets, I gave up and
put in my 60-year old thermostat and housing and --voila!-- no leak.
Unfortunately, the thermostat does not close, so it only serves to impede
the flow of water through the system. But that's better than water flowing
through the system and back into the watershed. Unfortunately, all that
banging around up there with that big fat hose...I managed to screw up the
capillary tube somehow and my temp gauge quit.
I remember there was someone out there rebuilding these old dual gauges.
Anyone have a name or contact?
Also, is there any quick source for a temporary replacement gauge that has a
BSP capillary tube fitting for the water tank? I know Stewart Warner used to
sell one, but I think the Chinese have abandoned British pipe thread. I've
emailed my local club a few minutes ago hoping someone has something extra
awaiting for other stages of the restoration to be completed.
John Deikis
Chelsea, MI
Ed said:
>Are you SURE the 'housing' is *DEAD* *FLAT*, John ??
>YOU check or Machine Shop ??
>Take a half dozen of yer [ straight <G> ] hairs.
Cut in 1/3rds and layout on block surface.
*Sans* gasket, put housing in-place and *tighten* *nuts* to say
5 - 10 inch/pounds [ makes sure housing is drawn down
*EVENLY* <G> !!
>Now try to extract hairs around housing but 1/3 way
around from 1st tried/pulled. Keep going' around
1/3rd a circle at a time. EASIEST one out is bad spot
<VBEG> !!
On Mon, May 30, 2011 at 2:31 PM, Lew Palmer <lpalmer@roundaboutmanor.com>wrote:
> Also be sure the mating surfaces are flat. A straight edge across the
> mating surfaces should show you if there is any warpage.
>
>
>
> Lew Palmer
>
>
> ------------------------------
>
> *From:* JohnD [mailto:johnsfolly@gmail.com]
> *Sent:* Sunday, May 29, 2011 10:40 PM
> *To:* Lew Palmer
> *Cc:* Mark J Bradakis; MG T List
>
> *Subject:* Re: [Mg-t] Making a gasket
>
>
>
> No. It's definitely the joint between the "gooseneck" and the thermostat
> housing. I just took it apart again, cut a new neoprene-cork gasket, put a
> bead of RTV on both surfaces, and tried to NOT over tighten it. I'll pour in
> some water in the morning and see what happens.
>
> John
>
> On Sun, May 29, 2011 at 9:46 PM, Lew Palmer <lpalmer@roundaboutmanor.com>
> wrote:
>
> Or a leaky seal in the water pump itself?
>
> Lew Palmer
>
> -----Original Message-----
> From: mg-t-bounces@autox.team.net [mailto:mg-t-bounces@autox.team.net] On
> Behalf Of Mark J Bradakis
> Sent: Sunday, May 29, 2011 6:29 PM
> To: MG T List
> Subject: Re: [Mg-t] Making a gasket
>
>
> And are you sure it is the joint that is leaking, and you are not
> having a porousity issue with the housing?
>
> mjb.
> ______________________________________________
>
> Mg-t@autox.team.net
> Donate: http://www.team.net/donate.html
> Suggested annual donation $11.47
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage <http://www.team.net/forums%0d%0aUnsubscribe/Manage>:
>
> http://autox.team.net/mailman/options/mg-t/lpalmer@roundaboutmanor.com
>
> ______________________________________________
>
> Mg-t@autox.team.net
> Donate: http://www.team.net/donate.html
> Suggested annual donation $11.47
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage <http://www.team.net/forums%0d%0aUnsubscribe/Manage>:
> http://autox.team.net/mailman/options/mg-t/johnsfolly@gmail.com
______________________________________________
Mg-t@autox.team.net
Donate: http://www.team.net/donate.html
Suggested annual donation $11.47
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
|