healeys
[Top] [All Lists]

[Healeys] Access to drive shaft IJs.

Subject: [Healeys] Access to drive shaft IJs.
From: bspidell at comcast.net (Bob Spidell)
Date: Fri, 9 Feb 2018 03:58:46 +0100 (CET)
References: <001a01d3a0de$cfc7d480$6f577d80$@homecall.co.uk> <066901d3a10b$ef1fd7b0$cd5f8710$@rr.com> <499883785.704440.1518128573955@mail.yahoo.com>
OK, I give up: why should you drain the gearbox?  I've removed driveshafts on 
several occasions without draining the gearbox; unless you somehow managed to 
destroy the OD rear seal I don't see how this could be an issue.


Bob

--------------------------------
Bob Spidell - San Jose, CA

> On February 8, 2018 at 11:22 PM Michael MacLean <rrengineer.mike at att.net> 
> wrote:
> 
>     Probably a good idea to drain the gearbox before removing the driveshaft. 
> Don't ask me how I learned that one.Mike MacLean
> 
>     Sent from Yahoo Mail on Android 
> https://overview.mail.yahoo.com/mobile/?.src=Android
> 
> 
>         > >         On Thu, Feb 8, 2018 at 2:16 PM, BJ8Healeys
> >         <sbyers at ec.rr.com> wrote:
> > 
> > 
> >            Just below the front U-joint the frame structure makes a sharp 
> > V.  Although it might be possible to remove the U-joint bolts from below 
> > (one at a time, if you can turn the driveshaft), the V restricts access.  
> > It would be much less tedious to do it from above after removing the 
> > tunnel.  The front U-joint bolts are locked with bent-over locking plates.  
> > You have to straighten the bent tabs to unscrew the bolts and nuts.  The 
> > rear U-joints are more easily accessed.  The driveshaft can be pulled out 
> > towards the rear.  It's in two pieces with a sliding spline joint between 
> > them.  There are  arrows on each piece for alignment.  Make sure you keep 
> > this alignment for balance reasons when you put it back together.
> > 
> >             
> > 
> >            Steve Byers
> > 
> >            HBJ8L/36666
> > 
> >            BJ8 Registry
> > 
> >            AHCA Delegate at Large
> > 
> >            Havelock, NC 
> > 
> >            [TARHEELY license plate]
> > 
> >             
> > 
> >            From: Healeys [mailto:healeys-bounces at autox.team.net] On 
> > Behalf Of simon.lachlan at homecall.co.uk
> >            Sent: Thursday, February 08, 2018 8:15 AM
> >            To: healeys at autox.team.net
> >            Subject: [Healeys] Access to drive shaft IJs.
> > 
> >             
> > 
> >            Hi,
> > 
> >            Another question?
> > 
> >            The manual tells one to remove the transmission tunnel in order 
> > to access the UJs.
> > 
> >            Can one do the job from underneath?
> > 
> >            I?ve never done UJs before so I?ll probably be appealing for 
> > help?..
> > 
> >            I have, I think, managed to source some decent ones. The price 
> > disparity on what?s available is remarkable??
> > 
> >            Simon
> > 
> > 
> >     > 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: 
<http://autox.team.net/pipermail/healeys/attachments/20180209/fdbe1d41/attachment.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image001.jpg
Type: image/jpeg
Size: 19755 bytes
Desc: not available
URL: 
<http://autox.team.net/pipermail/healeys/attachments/20180209/fdbe1d41/attachment.jpg>

<Prev in Thread] Current Thread [Next in Thread>