What ever you do DO NOT pull the overdrive and transmission together with
the long bolts. I have sold many overdrive housings to people that have done
just that and snapped off the tang on the adaptor plate.
The best way to do it is have two large channel lock pliers and squeeze the
to together. If the do not go together this way pull the overdrive off re
align the splines and then set the overdrive onto the transmission.
This is usually a 2 or 3 person job. Just be patient because if you have to
force it there is something wrong.
Lay a couple of 2 x 4 s on the ground and stand the transmission on the bell
housing. Then line up the splines of the overdrive and place the overdrive
onto the transmission, try to set the splines on the shaft and the ones in
the overdrive in the correct alignment so that you do not have to turn the
rear flange the least as possible. Them squeeze the two together by HAND not
with the long studs.
David Nock
British Car Specialists
209-948-8767
www.britishcarspecialists.com
-----Original Message-----
From: David Porter
Sent: Monday, July 07, 2014 12:34 PM
To: Fred Wescoe ; healeys
Subject: Re: [Healeys] Overdrive
If all you say is and if the brass thrust washers are still
centralized.. then you are not pulling the sides down equally. They have
to be nearly identical in pull..
dave
On 7/7/2014 12:33 PM, Fred Wescoe wrote:
> I am trying to reattached the overdrive unit to the transmission of my
> BJ7. The two sets of splines in the overdrive are aligned properly and I
> have used safety wire to wire down the pump plunger to it lowest position.
>
> The overdrive is on the transmission studs and the ends of the stubs are
> just at the rear face of the overdrive case, not enough to get a nut on
> but
> close. The housing of the overdrive is 3/16" away from the transmission
> housing.
>
> I have put grease on the end of the main-shaft, grease on the roller on
> top
> of the pump plunger and grease on the bottom of the eccentric ring that
> operates the pump plunger.
>
> I have tapped on the drive flange (not banged), tried to twist the
> overdrive, tried to shake it left/right/up/down and tried to rotate the
> drive flange. The transmission is in 4th so nothing moves. I have also
> tried all of these with the transmission in neutral. No luck with any of
> that.
>
> I have tried many, many times to seat the overdrive and it just will not
> go
> together. It is always just the 3/16' short of mating up.
>
> What am I doing wrong? What should I look for or do?
>
> Fred
> 63 BJ7
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/frogeye@porterscustom.com
>
>
>
--
Dave Porter Porter Custom Bicycles 2909 Arno St. NE Albuquerque, NM
87107 505-352-1378 Go HERE: my world www.porterbikes.com/
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
http://autox.team.net/mailman/options/healeys/healeydoc@sbcglobal.net
_______________________________________________
Archive: http://www.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
|