fot
[Top] [All Lists]

Re: [Fot] Rear main rope seal alternatives?

To: Michael Moore <mmoore@mtmcpafirm.com>
Subject: Re: [Fot] Rear main rope seal alternatives?
From: Phil Gott via Fot <fot@autox.team.net>
Date: Fri, 15 May 2020 09:52:10 -0400
Cc: Friends Of Triumph <fot@autox.team.net>
Delivered-to: mharc@autox.team.net
Delivered-to: fot@autox.team.net
References: <CH2PR04MB6935735653B421292CF2C044B4BD0@CH2PR04MB6935.namprd04.prod.outlook.com>
Thanks to all who replied.

I asked because we are doing a bottom end rebuild, and Iâ??m very worried that 
if any kind of goo gets down into the ring pack, it will stick the rings. 
Thanks for the tips. The â??stringâ?? of tips should be included in this email. 
Some very clever!
Hope to see you in Ohio,

Sent from my iPhone

> On May 15, 2020, at 9:20 AM, Michael Moore <mmoore@mtmcpafirm.com> wrote:
> 
> Did you get any responses to your question, I would also like to know if 
> the is a less messy way to do it.
> 
> Thanks
> Mike
> 
> Michael T. Moore, CPA
> 3255 West 26th Street
> Erie, PA 16506
> 
> Phone:  814-616-8652  ext 100
> Fax:        888-865-5279
> Email:    mmoore@mtmcpafirm.com
> 
> This electronic mail message contains confidential and legally privileged 
> information intended only for the use of the recipient. If the reader of this 
> message is not the intended recipient, the reader is hereby notified that any 
> dissemination, distribution, copying or other use of this message is strictly 
> prohibited and is hereby instructed to notify the sender immediately by 
> return email and destroy this copy of this message.
> 
> 
> 
> -----Original Message-----
> From: Fot <fot-bounces@autox.team.net> On Behalf Of Phil Gott via Fot
> Sent: Sunday, May 10, 2020 8:19 PM
> To: Friends Of Triumph <fot@autox.team.net>
> Subject: [Fot] Rear main rope seal alternatives?
> 
> Seems as if every time I use Permatex Aviation Cement to soak my rope seals 
> the mess gets worse and worse. 
> Is there a good alternative to Aviation Cement or to the rope seals entirely? 
> I have tried RTV, but it is very hard to get it in there with no air gaps. 
> Building another engine this week and am wondering about a better way to do 
> it.
> Phil Gott
> 
> Sent from my iPhone
> _______________________________________________
> fot@autox.team.net
> 
> http://www.fot-racing.com
> 
> Donate: http://www.team.net/donate.html
> Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
> Unsubscribe/Manage: 
> http://autox.team.net/mailman/options/fot/mmoore@mtmcpafirm.com
> 
> 

_______________________________________________
fot@autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
Unsubscribe/Manage: 
http://autox.team.net/mailman/options/fot/mharc@autox.team.net


<Prev in Thread] Current Thread [Next in Thread>