No worries Jack,
Thought it may have been useful to offer an explanation why this issue happens
to some people and not too others.
Happy days!
Cheers for now
"You can Make a Small Fortune From Motor Racing. As long as You Started With A
Lage Fortune!"
Kind Regards
Peter Vucinic
TR4 - TR7 V8 - Spitfire MkII
_______________________________________________
fot at autox.team.net
http://www.fot-racing.com <http://www.fot-racing.com/>
Archive: http://www.team.net/archive
From: Jack Wheeler [mailto:jwheeler1947 at yahoo.com]
Sent: Thursday, 8 June 2017 10:41 AM
To: Peter Vucinic
Cc: fot at autox.team.net
Subject: [Fot] TR4 ARP Flywheel Bolts Question
Hi Peter. You are way ahead of me from an engineering standpoint. I was a
bean counter. All I was doing here was sharing my experience with the TR-4
engine, over a 25 year racing career, for what that's worth.
Thanks for your comments.
Jack
_____
On Wednesday, June 7, 2017, 7:52:47 PM EDT, Peter Vucinic <pvucinic at
netspace.net.au> wrote:
Jack,
Indeed lots good discussion to get the ?juices flowing?
This is a subject that is close to my heart and I am familiar with, and have
been dealing with and resolving for 30 years in industry.
Simply?
The crank shaft bolts are NOT shearing. The bolts are being stretched,
clearance/low tension occurs, then fatigue failure will set in.
The cause. Torsional Vibration of the crank shaft. Torsional vibration is a
BENDING moment or moments in the crankshaft.
The SEVERITY and WHERE this bending moment occurs depends on a number of
factors such as crankshaft weight, number of main journals, flywheel weight,
harmonic damper etc. and is a function of the operating RPM?s.
Check out the below clip for a good visual on what can happen.
https://www.youtube.com/watch?v=xTJUSRSJxpA
https://www.youtube.com/watch?v=X4pCiNozLkk
If my memory serves me correct, I believe Kas did a lot of work on the TR6
engine on this very subject! I think from memory the flywheel run out at
certain RPM?s was almost ??
So, if you accept the above explanation on the failure mode of the se bolts.
You can now understand WHY this issue DOESN?T happen to everyone with the same
basic engine and components.
It?s all extremely dependent on all the types of components used, component
weights AND what RPM?s you like to make your MAX, and running RPM's through the
gears etc. etc.
This is the EXACT reason why constant RPM engines like SHIPS and racing boats,
steam turbines AVOID certain RPM?s within plus/minus a few hundred of that
figure/point. As it significantly reduces the risk of severe and damaging
torsional vibrations in the crankshaft system.
There is basically two major outcomes if you have this problem - Flywheel bolts
are stretched/items become ?loose? OR the crankshaft breaks.
If the issue is not resolved, NO amount of Loctite (Loctite on grade 8 bolts is
another while issue) or tension will fix it. I have had 2 and 1/2? diameter
bolts where the head of the bolt has been completely ?popped? off. Let?s not
forget if you are operating at say, 7,000 RPM, that can equates to 232 to 348
times a SECOND, that each bolt is exposed to this problem
(stretching/fatigue). So I NEVER use 2nd hand bolts.
My 2 cents worth. Lots of good articles out there on crankshaft torsional
vibration
"You can Make a Small Fortune From Motor Racing. As long as You Started With A
Lage Fortune!"
Kind Regards
Peter Vucinic
TR4 - TR7 V8 - Spitfire MkII
_______________________________________________
fot at autox.team.net
http://www.fot-racing.com <http://www.fot-racing.com/>
Archive: http://www.team.net/archive
From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of Jack Wheeler via
Fot
Sent: Thursday, 8 June 2017 5:06 AM
To: timmmurphh at gmail.com
Cc: fot at autox.team.net
Subject: Re: [Fot] TR4 ARP Flywheel Bolts Question
Lots of interesting discussion here. This may surprise some of you, but my
experience shows that the Factory knew what they were doing when they were
designing the flywheel connection to the crankshaft.
Early in my career, racing a TR-4A (SCCA D Production, then moved to E
Production) I sheared off flywheel bolts on a number of occasions, and each
time, I tried to figure out the cause of the failure. Understanding the causes
of these failures, and with suggestions from other TR racers, here is the
combination I came up with, which I used for the last 17 years I raced. And,
of course, this was the time during which I was producing the most HP and
turning the lowest lap times (thus more strain on this connection).
First, I had 2 flywheel dowel holes drilled. By that time, I was using a
Tilton aluminum flywheel and dual disk racing clutch. The stock crankshaft had
2 dowel holes, but for whatever reason, they only used one dowel. The stock
flywheel came with 2 dowel holes drilled, but they were only 90 dewgrees apart,
and they didn't go all the way through the flywheel, and they only used 1
dowel. I don't recall if the Tilton flywheel came with 2 dowel holes, or if I
had to have a second one drilled 180 degrees from the first one. So, I
installed dowels in both dowel holes in the stock crankshaft. I found some
longer dowels that would go to the seat at the bottom of the crankshaft holes,
all the way through the flywheel, and still leave about 1/8" sticking out on
the flywheel side. Next is very important!!! I installed the stock lock tabs,
such that the tabs covered the ends of the dowels sticking out. This kept the
dowels from backing out, in addition to keeping the bolts from loosening up.
As a back-up, I also used blue loc-tite on the stock bolts. In fact, I never
purchased a new flywheel bolt. I had enough used bolts laying around that I
just picked out 4 that looked good (threads, wear on the shoulder, etc.), had
them magnafluxed, and they were good to go. Never broke one using this
procedure. I used the factory recommended torque spec.
I know this sounds pretty simple, and it doesn't involve spending a lot of
money on expensive parts, but it worked for me. There may be better options
out there, but my concern was always to find something that worked, no matter
what part of the car I was working on. Then "if it ain't broke, don't fix it".
This approach worked for me for a long time.
Footnote: The last time I sheared off a flywheel was at The Runoffs in 1980
(my first year at The Runoffs). Turns out I had installed the lock tabs 90
degrees off from where they should have been. Without the lock tabs to secure
them, the dowels backed out, which eventually allowed the connection to loosen
up and sheared off the bolts, spinning the engine to 8,500 RPM's (coming down
the back straightaway). This necessitated a change to a back-up engine. With
the approach described above, I never sheared off another flywheel.
Good luck, and I hope you all find a solution that works for you.
Jack
_____
On Wednesday, June 7, 2017, 1:50:57 PM EDT, timmmurphh--- via Fot <fot at
autox.team.net> wrote:
Is there a shorter (3/4 inch) 3/8-20 bolt that could be used for the flywheel
that you know of?
Tim
From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of Robert Deanes via
Fot
Sent: Tuesday, June 6, 2017 10:42 AM
To: Barr, Scott <sbarr at mccarty-law.com>
Cc: FOT <fot at autox.team.net>
Subject: Re: [Fot] TR4 ARP Flywheel Bolts Question
the shorter ARP bolts are 350-2802.....you don't have to grind the end of the
bolt
On Mon, Jun 5, 2017 at 4:36 PM, Barr, Scott via Fot <fot at autox.team.net>
wrote:
<< Don't you guys use steel inserts in those flywheel holes? >>
Nope ? I?ve always used them as supplied. And so long as I remembered to check
the clearance for the radius under the head, it?s been fine. Frankly, I always
wondered about why it was OK to torque the flywheel bolts down onto a
relatively soft aluminum flywheel, but bad to use a steel washer ? which was
almost certainly harder. But I?ve always used Loctite on the flywheel bolts:
mostly red, though sometimes blue.
Scott (B.)
From: Scott Janzen [mailto:sjanzen at me.com]
Sent: Monday, June 05, 2017 3:28 PM
To: Barr, Scott <sbarr at McCarty-Law.com>
Cc: timmmurphh at gmail.com; Steve Yott <tr4 at wi.rr.com>; STEPHEN BOROWSKI
<biznzman at pacbell.net>; FOT <fot at autox.team.net>
Subject: Re: [Fot] TR4 ARP Flywheel Bolts Question
Don't you guys use steel inserts in those flywheel holes?
Sent from my iPhone
On Jun 5, 2017, at 7:55 AM, Barr, Scott via Fot <fot at autox.team.net> wrote:
This is what it looks like if you forget to chamfer the flywheel holes to clear
the radius under the head.
<image001.jpg>
From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of timmmurphh--- via
Fot
Sent: Sunday, June 04, 2017 5:53 PM
To: 'Steve Yott' <tr4 at wi.rr.com>; 'STEPHEN BOROWSKI' <biznzman at
pacbell.net>; fot at autox.team.net
Subject: Re: [Fot] TR4 ARP Flywheel Bolts Question
Thanks for the clarification Steve, that makes sense.
Tim
From: Steve Yott [mailto:tr4 at wi.rr.com]
Sent: Sunday, June 4, 2017 4:56 PM
To: timmmurphh at gmail.com; 'STEPHEN BOROWSKI' <biznzman at pacbell.net>
Subject: RE: [Fot] TR4 ARP Flywheel Bolts Question
The reason they state to not use washers is they are afraid that the washers
used will (1) not be hard enough and will compress under the bolt head and (2)
all ARP bolts have very liberal radii between the head and shank. If there is
a tight fitting washer this would be strain on this radius and could break the
head.
The 7/16? ARP bolts used on Chevy flywheels is what I fit to TR?6, late
Spitfires and modified TR4 cranks. These bolts come with the special washers
to use with them. I have used a proper washer under the 3/8? ARP bolts many
times with no problems using a correct washer. You can also use an ARP crown
wheel bolt for the same purpose and these come with proper washers.
Steve Yott
From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of timmmurphh--- via
Fot
Sent: Sunday, June 04, 2017 1:59 PM
To: 'STEPHEN BOROWSKI' <biznzman at pacbell.net>; fot at autox.team.net
Subject: Re: [Fot] TR4 ARP Flywheel Bolts Question
FWIW
I just got a set of ARP 206-2802 flywheel bolts from Pegasus for the TR4. They
are for ?BMC A series?. The instruction specifically says, ?DO NOT USE ANY
WAHERS?, yes, all in caps for emphasis! They further state that ARP will not
be responsible for failures is washers are used. The instructions also say,
?Make sure there is an adequate chamfer under the bolt holes on the flywheel to
clear the radius under the head of the bolt.? Torque is 55 Ft-Lb with
specified lubricants on the threads.
I?ve never had that much good luck grinding the ends of bolts and still having
it square so as not to start it cocked and runing the female threads. Maybe
it?s just me?
Tim
From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of STEPHEN BOROWSKI
via Fot
Sent: Friday, June 2, 2017 3:28 PM
To: FOT List <fot at autox.team.net>
Subject: [Fot] TR4 ARP Flywheel Bolts Question
Does anyone have experience using the ARP flywheel bolts sold by Moss and
others?
I understand that you may have to shorten the bolt or it breaks the rear seal???
Are they supposed to have a washer or not?
Thxs. Steve
_______________________________________________
fot at autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
_______________________________________________
fot at autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
--
rob deanes
TR Racer
_______________________________________________
fot at autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/fot/attachments/20170608/4b8f1e38/attachment.html>
|