fot
[Top] [All Lists]

Re: [Fot] Help identifying Spitfire comp rear axle

To: Kas Kastner <kaskas@cox.net>
Subject: Re: [Fot] Help identifying Spitfire comp rear axle
From: Tim Pettenati <1964spitfire@pacbell.net>
Date: Tue, 7 Feb 2012 15:59:28 -0800 (PST)
Kas,

Photos are here:
http://www.flickr.com/photos/14001317@N02/sets/72157629218411585/

Do you need
a picture of something else. 
Axles are still in the car, so kinda hard to get
a good photo.

The spicer 5-178X (1350 series) you mention is slightly larger
with a 1.188 cap.

Mine use spicer 1310 series u-joints with a 1.062 cap and
3.219 overall length. 

Thanks,
Tim
 



________________________________
From: Kas Kastner <kaskas@cox.net>
To: 1964spitfire@pacbell.net; fot
<fot@autox.team.net>
Sent: Tue, February 7, 2012 2:15:18 PM
Subject: RE: [Fot]
Help identifying Spitfire comp rear axle


Your description does not help me
much, I need a photo.  I built forged one 
piece axles in the early 1970's
that were one piece with the hub and the axle 
all one forged part made of
very expensive vascojet 8000 special steel.  Mueler 
was given the specs and
forging dies to carry on that work when I left Triumph.  

We used a Forklift
U-joint for the mating parts and it was very very good and  
strong.  This
number may be the one, but it also may be for the engine dyno 
cardian shaft
(which was lot bigger).  I only have this Spicer part number so 
cannot tell. 
Anyway a clue is the forlift info.  If all else fails look there. 
My spicer
number is 5-178X .That is for a U-joint kit.

Never be beaten by equipment
 
> Date: Tue, 7 Feb 2012 12:43:49 -0800
> From: 1964spitfire@pacbell.net
> To:
fot@autox.team.net
> Subject: [Fot] Help identifying Spitfire comp rear axle
>
> Can anyone help identify this Spit rear axle from the photos,
> and/or what
> parts they was built from?
> 
> http://flic.kr/s/aHsjyzQBGV
> 
> The axle
shaft is 1"
> dia with .9875 X 10 splines. 
> According to the DPO it's a
Mother Mueller part,
> but he's provided a few tall tales on the car's
history.
> It's possible since
> car was built in SoCal, late 70' - early
80's.
> 
> I'd at least like to find were
> the Yoke was sourced from. 
> One
side has quite a bit of play.
> 
> Any leads would
> be appreciated. 
> 
>
Cheers,
> Tim
> _______________________________________________
>
fot@autox.team.net
> 
> http://www.fot-racing.com
> 
> Donate:
http://www.team.net/donate.html
> Archive: http://www.team.net/archive
>
Forums: http://www.team.net/forums
> Unsubscribe:
http://autox.team.net/mailman/options/fot/kaskas@cox.net
_______________________________________________
fot@autox.team.net

http://www.fot-racing.com

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums


<Prev in Thread] Current Thread [Next in Thread>