Same here, on my 1147 engine ... a simple double-male fitting into the oil
filter adapter (on the side of the block) and a tee right there. The line is
the one coming from the cooler and the stem of the tee is the line going to
the Accusump so what goes into the Accusump is clean, cool oil.
And then ... you screw that one in first, the short line reaching to the oil
filter second. :-)
--Rocky Entriken
----- Original Message -----
From: "Brad Kahler" <brad.kahler@141.com>
To: <fot@autox.team.net>
Sent: Wednesday, February 04, 2009 5:47 PM
Subject: Re: [Fot] Question on Accusump Install with External Oil Lines On a
Spitfire
> On Susan's 1300 engine we have a remote oil filter adapter that we have
> T'eed into for the Accusump. This gives us a large diameter all the way
> into the oil gallery passages.
>
> Brad
>
>
> Barr, Scott wrote:
>> I've used a 1/8th NPT fitting there. I don't know whether that will be
>> big enough for what you want to do - whether 3 or 4 1/8th NPT fittings
>> will actually flow the amount of oil you want. But you could drill them
>> out and tap them for either 1/8th or 1/4NPT and buy the adapters from
>> Pegasus to fit your AN fittings. I actually have a 3/8NPT fitting in
>> the center main gallery plug where my Accusump is plumbed into my
>> engine.
>>
>> Check Pegasus - your male NPT pipe to male AN adaptor part numbers would
>> be 3250-02-06 (1/8NPT to 6AN adapter) or 3250-04-06 (1/4NPT to 6AN
>> adapter). (Page 83 of the current catalog) Or just call the tech line
>> at Pegasus (or similar) and they'll tell you what you need.
>>
>> Scott B.
>>
>> -----Original Message-----
>> From: fot-bounces@autox.team.net [mailto:fot-bounces@autox.team.net] On
>> Behalf Of Glenn Franco
>> Sent: Wednesday, February 04, 2009 3:38 PM
>> To: Friends of Triumph
>> Subject: [Fot] Question on Accusump Install with External Oil Lines On a
>> Spitfire
>>
>> I'm in the process of installing a 3 quart Canton Accusump on my 1.3L
>> Spit engine. I'm planning to run 6 an to the engine compartment and
>> split off to the main gallery plugs on the side of the engine block.
>> The early 1.3L has three plugs and the later has 4. I'm having trouble
>> locating a fitting that will fit into the gallery openings. They appear
>> to be 5/16 fine thread.
>> I've reviewed the write up on page 131-2 in Kas's Triumph Preparation
>> Handbook that shows Steve Smith's installation. What is not listed is
>> the hardware that was used.
>> It looks like a flow bolt and banjo fitting could be used but I cannot
>> find any in that size.
>> Is anyone familiar with this setup and if so where did you source the
>> fittings that would screw into the gallery plug holes?
>>
>> Any help would be appreciated.
>> Thanks in Advance
>> Glenn Franco
>> 72 Spit Race Car and various other Triumphs
>> Fot mailing list
>> Fot@autox.team.net
>> http://autox.team.net/mailman/listinfo/fot
>> _______________________________________________
>> Support Team.Net http://www.team.net/donate.html
>>
>> http://www.fot-racing.com
>>
>> Fot mailing list
>> Fot@autox.team.net
>> http://autox.team.net/mailman/listinfo/fot
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
>
> http://www.fot-racing.com
>
> Fot mailing list
> Fot@autox.team.net
> http://autox.team.net/mailman/listinfo/fot
_______________________________________________
Support Team.Net http://www.team.net/donate.html
http://www.fot-racing.com
Fot mailing list
Fot@autox.team.net
http://autox.team.net/mailman/listinfo/fot
|