One more note about taking off the tape. when I say "ready to install
the line" I mean SECONDS away. When you take the tape off the braid
begins relaxing from the hose in the area of the cut. Thirty seconds
after you pull the tape off it will resemble a trumpet bell. You've
got about five seconds to get the outer part of the fitting on to the
hose.
Bill Babcock
billb@bnj.com
bnj Website for Babcock & Jenkins, a direct and interactive agency
You can subscribe to my Blogs
Via email:
All Aluminum Tour: Touring and racing classic North American tracks.
http://www.feedblitz.com/f/?Sub=168395
Ponohouse : Living and playing in Maui. http://www.feedblitz.com/f/?
Sub=168304
or Via RSS
Ponohouse: http://feeds.feedburner.com/PonoHouse
AllAluminumTour: http://feeds.feedburner.com/AllAluminumTour
On Mar 15, 2007, at 3:00 PM, Bill Babcock wrote:
> Aeroquip lines, or any of the other stainless braid lines are
> preferable to rubber for lots of reasons, most of them involving
> flames. I cut stainless lines several different ways, but it's all
> generally the same. Wrap the line tightly in the area to be cut with
> a single wrap of duct tape, cut the line. Don't take the tape off
> until you're ready to install the line. Proceed according to the
> manufacturers instructions for installing the fitting.
>
> To cut, you can either use a very fine hacksaw and light cutting
> pressure or a very thin abrasive disk in a high speed angle grinder.
>
> Tony, you should be ashamed of yourself for using those piece of s*&t
> hose clamps. they might be cheaper than getting the right fittings,
> but one engine fire equals a lot of fittings. Carrol Smith is
> spinning in his grave just thinking about it. He used Aeroquip stuff
> on his tow rig. BTW, the best way to learn about car plumbing is
> Carrol Smiths book about car plumbing and fasteners. Buying that book
> will cost you a lot of money--not in fittings--they're relatively
> cheap, reusable and you simply don't need that many, but in Bolts and
> Nuts.
>
> Bill Babcock
> billb@bnj.com
> bnj Website for Babcock & Jenkins, a direct and interactive agency
>
> You can subscribe to my Blogs
> Via email:
> All Aluminum Tour: Touring and racing classic North American tracks.
> http://www.feedblitz.com/f/?Sub=168395
> Ponohouse : Living and playing in Maui. http://www.feedblitz.com/f/?
> Sub=168304
>
> or Via RSS
> Ponohouse: http://feeds.feedburner.com/PonoHouse
> AllAluminumTour: http://feeds.feedburner.com/AllAluminumTour
>
>
>
> On Mar 15, 2007, at 2:12 PM, steve wrote:
>
>> My Dad's old TR3 arrived via Passport Transport on Monday night.
>> Each night after work, I'm out there puttering around trying to
>> tidy up the engine compartment a bit. It's in great condition but
>> I've always wanted to clean up the location of a few lines, wires,
>> etc..
>>
>> One of the things I'd like to do is to replace the 17year old
>> Aeroquip fuel lines with new stuff.
>>
>> The braided SS fuel hoses on the car were cut to length with a hack-
>> saw. Then, the prickly ends were wrapped in a few loops of black
>> tape. Over that goes a hose clamp. When I shop around online for
>> Aeroquip tubing and fittings, all the ends available seem to be
>> THREADED fittings. Is there a more elegant solution to clamp the
>> ends onto the SU carb fuel-input pipes than the hack saw, tape,
>> hose clamp method?
>>
>> Anyone use rubber fuel tubing instead of the braided line?
>>
>> ~Steve
>> _______________________________________________
>> Fot mailing list
>> Fot@autox.team.net
>> http://autox.team.net/mailman/listinfo/fot
> _______________________________________________
> Fot mailing list
> Fot@autox.team.net
> http://autox.team.net/mailman/listinfo/fot
_______________________________________________
Fot mailing list
Fot@autox.team.net
http://autox.team.net/mailman/listinfo/fot
|