Gary,
We sell VTO Wheels.
On 67.5 and later we recommend 15x7 +18 offset. Earlier cars its a 15x6
+24.
Tire size 195/55-15.
I hope this helps.
Dave Patten, Owner
FutoFab, LLC
199 Stark Hwy So
Dunbarton, NH 03046
Website - www.FutoFab.com <http://www.futofab.com/>
e-mail - dave@futofab.com
On Sat, Aug 17, 2013 at 11:20 AM, Gary J <geegc@aol.com> wrote:
> I want to get a set of new wheels for my 2000. B does anybody have a
> recommendation for a good source with the proper offset?
>
> Gary
>
>
> Sent from my Verizon Wireless 4G LTE Smartphone
>
> -------- Original message --------
> From: "Graeme S." <graemes@internode.on.net>
> Date: 08/15/2013 11:18 PM (GMT-08:00)
> To: datsun-roadsters@autox.team.net
> Subject: Re: [Roadsters] '69 SPL311 rear wheel cylinders
>
> + one for not bothering with a re-build kit.
> You can get the original slaves re-sleeved with stainless steel, THEN a
> re-build kit.
> That way they'll last forever.
>
> Regards,
> Graeme S.
> nissanman.shutterfly.com
>
> On 16/08/2013 2:21 PM, dana nojima wrote:
> > Don't waste your time with rebuild kits.B You will normally find the
> > cylinders pitted and so if you go through the trouble with putting in new
> > rubber, they well still leak.
> >
> >B B
> >
> > If you hone the cylinders enough to get rid of the pits, then they will
> > still leak.
> >
> >B B
> >
> > Been there tried that,
> >
> >B B
> >
> > Dana
> >
> >B B
> >
> > -----Original Message-----
> >
> > From: Leonard Sprague <sprague@jandmcontractors.com>
> >
> > To: datsun-roadsters <datsun-roadsters@autox.team.net>
> >
> > Sent: Thu, Aug 15, 2013 2:40 am
> >
> > Subject: [Roadsters] '69 SPL311 rear wheel cylinders
> >
> >B B
> >
> >B B
> >
> > Hello,
> >
> > Can anyone tell me where I can find replacementrear wheel cylinders
> >
> > both sides) for my '69 SPL311 (1600roadster)?Do any of the vendors
> >
> > tock these?
> >
> > Also, has anyone tried using this Napa rebuild kit?
> >
> > ttp://
> www.napaonline.com/Catalog/CatalogItemDetail.aspx/Wheel-Cylinder-Kit-R
> > e
> >
> > ar/_/R-UBP1065_0379995539
> >
> > Thank you in advance for your assistance.
> >
> > Lenny Sprague
> >
> > PL311-25453/VG30
> >
> > On 9/28/2007 3:45 PM, Pete Peters wrote:
> >
> >B B B From the Parts Interchange page on 311s.org:
> >
> >B B
> >
> > "NAPA, rear wheel cylinder rebuild kit part # UP1065 - this is for the
> 3/4"
> >
> > wheel cylinders if yours are not in bad shape and basically only need new
> >
> > rubber parts."
> >
> >B B
> >
> > Not sure about rebuild kits, but whole cylinders are available from the
> >
> > vendors.
> >
> > On 9/28/2007 12:14 PM, Dan Zubkoff wrote:
> >
> > Try Napa rebuild kit UBP-1065.
> >
> > --
> >
> > eonard Sprague
> >
> > resident, J and M Contractors
> >
> > 352) 262-4788
> >
> > ttp://www.JandMContractors.com/sprague.shtml
> > ________________________________________
> >
> > datsun-roadsters@autox.team.net
> >
> > Donate: http://www.team.net/donate.html
> > Archive: http://www.team.net/archive
> > Forums: http://www.team.net/forums
> > Unsubscribe:
> http://autox.team.net/mailman/options/datsun-roadsters/graemes@internode.on.net
> ________________________________________
>
> datsun-roadsters@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/options/datsun-roadsters/geegc@aol.com
> ________________________________________
>
> datsun-roadsters@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/options/datsun-roadsters/futofab@gsinet.net
________________________________________
datsun-roadsters@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe:
http://autox.team.net/mailman/options/datsun-roadsters/mharc@autox.team.net
|