"better penetration" I'm not saying anything.
Charlie B.
-----Original Message-----
From: datsun-roadsters-bounces@autox.team.net
[mailto:datsun-roadsters-bounces@autox.team.net] On Behalf Of Vince
Strazzabosco
Sent: Friday, August 21, 2009 7:59 PM
To: tputland@charter.net; barterdude@comcast.net;
datsun-roadsters@autox.team.net; Keith0alan@aol.com
Subject: Re: [Roadsters] What is recommended for breaking rust loose
I heard about this too and have been meaning to try some.
One other thing I
didn't mention is being able to use a hammer and punch, etc on the flats of
the stuck bolt to hit it straight on and let the shock break the bond.
Again,
using plenty of penetrating whatever again and again. For some bolts, it
helps to scrape or clean the grime or loose rust away to allow better
penetration.
vince
--- On Fri, 8/21/09, Keith0alan@aol.com
<Keith0alan@aol.com> wrote:
> From: Keith0alan@aol.com <Keith0alan@aol.com>
>
Subject: Re: [Roadsters] What is recommended for breaking rust loose
> To:
tputland@charter.net, vstrazzabosco@yahoo.com, barterdude@comcast.net,
datsun-roadsters@autox.team.net
> Date: Friday, August 21, 2009, 7:43 AM
>
>
>
>
>
>
> A 50-50 mix of ATF and acetone works great and is
> cheap. I
have a spray
> bottle of it in the shop. I have seen a couple of tests
>
where it works better
> than any commercial product.
> B
> keith
>
williams
> ccfcccs
> http://www.clarkcountyferalcats.org
>
> b If
> Not Us,
Then Who? If Not Now, Then When?b
> B
>
> In a message dated 8/20/2009
9:26:31 P.M. Pacific
> Daylight Time,
> tputland@charter.net writes:
> Hey
>
Vince, welll put and I say: AMEN BROTHER!!
>
> I am at the end of stripping
> a 69 2000 rust bucket.
>
> All I can add is this:B Be prepared to
>
replace every single nut and bolt you cannot get apart
> easily. If it is
>
rusted...the metal has expanded...and will no longer be
> usable.
>
>
>
Tim
> Belleville, WI.
> '70 SPL AND SRL
> Still clueless but always
>
learning
>
> ---- Vince Strazzabosco <vstrazzabosco@yahoo.com>
> wrote:
>
>
> =============
> Kroil, PB Blaster, propane torch heat, careful
>
breaking loose with wrenches
> and sockets that fit well, patience, patience,
> patience.
>
> vince
> ________________________________________
> Support
> Team.NetB http://www.team.net/donate.html
>
> You are subscribed as
>
keith0alan@aol.com
>
> Datsun-roadsters mailing
> list
>
>
http://www.team.net/archive
>
>
http://autox.team.net/mailman/listinfo/datsun-roadsters
You are subscribed as vze2fhba@verizon.net
Datsun-roadsters mailing list
http://www.team.net/archive
http://autox.team.net/mailman/listinfo/datsun-roadsters
________________________________________
Support Team.Net http://www.team.net/donate.html
Datsun-roadsters mailing list
http://www.team.net/archive
http://autox.team.net/mailman/listinfo/datsun-roadsters
|