datsun-roadsters
[Top] [All Lists]

Re: roadster brakes question

To: <SLBESQ@aol.com>, <roadster@texoma.net>, <datsun-roadsters@autox.team.net>
Subject: Re: roadster brakes question
From: "Fred Schroeder" <roadster2@texoma.net>
Date: Sat, 22 Feb 2003 20:30:04 -0600
Making brake lines is not a bad task.  You will have to obtain a double
flare tool.  They are simple and straight forward to use.  The fittings on
my '70 are all 3/8 x 24.  I would suspect that they are the same on the
67.5.  If you can find a pre-made length close to the original by all means
use it.

It will require a complete system bleed at this point.  This is something
you should do once a year anyway.  Brake fluid is 'hygroscopic' meaning it
absorbs moisture like a sponge.  I suggest that you get a set of  'Speed
Bleeders'.  You can order them over the 'net.  I saw them at O'Rileys auto
supply the other day.  They, too, are 3/8 x 24. They have a check valve
built into them to allow one person bleeding.  The clutch fluid needs to be
changed as well.


Best regards,

Fred Schroeder
Denison, TX
SRL311-13359
TDROC
Reg e-mail  sitsinwest@texoma.net
Home page  http://home.texoma.net/~sitsinwest
----- Original Message -----
From: <SLBESQ@aol.com>
To: <roadster@texoma.net>; <datsun-roadsters@autox.team.net>
Sent: Saturday, February 22, 2003 10:41 AM
Subject: roadster brakes question


> hi fred and everyone on the list:
>
> i've just been reading your (fred's) tale on your website re your roadster
> restoration.  i'm looking for info on the brakes.  i wanted to install
> braided stainless lines for all three rubber lines on my car (67.5).  i
> ordered some from pegasus (the wrong ones it turns out).  to start, i
> disconnected the rubber line from the hard line at the driver's side front
> wheel.  doing so drained all the fluid.  the hard line to rubber line
> connection was quite tight and took alot of effort to free.
>
> after discovering i had the wrong braided stainless lines (female at both
> ends), i attempted to reassemble the hard line to the rubber line.  the
hard
> line fitting no longer wanted to thread down easily into the rubber line.
i
> eventually got it going with much effort.  so much effort in fact, it
seemed
> as if i was cross threading it.  i backed the fitting out and inspected
the
> threads on both it and the rubber line.  the threads in the rubber line
> seemed fine.  but the bottom threads of the hard line fitting appeared to
be
> gone, smoothed away, leaving about one-half inch of thread.  i didn't
inspect
> it when it first came out, but it did not look right at this point.  i
again
> attempted to reinsert the hard line fitting, and got it tight as i could.
> after filling the reservoir again, and pumping the pedal a few times,
fluid
> was everywhere from that connection, exiting the system from between the
hard
> line fitting and the hard line, up through that fitting.  did that make
> sense?
>
> i ordered the correct braided lines from les.  and now need to install
them.
>
> (still with me?  thank you very much for reading this if you are!)
>
> so on to my questions:
>
> 1.    i assume that i need to replace the hard line to the driver's side
> front, because of the condition of the fitting.  if so, can i just buy a
> pre-made length of the proper diameter brake line at the auto parts store
and
> bend then install it?  are those lines double-flared?  if not, can i still
> buy that pre-made line and add another flare, or must i start from
scratch,
> and do both flares?  (i have some experience with flaring tools from my
days
> in the pipe fitters union, but own none.).
>
> 2.    must i bleed the master at this point as well?  given that it nearly
> emptied when i  disassembled the lines.
>
> i apologize for the length of this book-like email.  i will greatly
> appreciate any help or guidance you can give me.  thank you.
>
> steve
> 67.5MIZU

///  datsun-roadsters@autox.team.net mailing list
///  Archives at http://www.team.net/archive


<Prev in Thread] Current Thread [Next in Thread>