--===============6819687154380231599==
boundary="----=_Part_3840676_565455535.1643463536131"
------=_Part_3840676_565455535.1643463536131
Content-Transfer-Encoding: quoted-printable
OK.=C2=A0 No turn signals at all may be the hazard switch.=C2=A0 The hazar=
d switch disconnects the turn signal flasher.=C2=A0 If those contacts are d=
odgy the turn signals won't work.=C2=A0 If the contacts for the right side =
are dodgy they won't work in the hazard mode.=C2=A0 I'd start there.
=20
Dave=20
=20
=20
-----Original Message-----
From: rmf3860 rmf3860 <bobfabie@gmail.com>
To: DAVID MASSEY <dave1massey@cs.com>
Cc: 6pack@autox.team.net <6pack@autox.team.net>
Sent: Fri, Jan 28, 2022 6:11 pm
Subject: Re: [6pack] Two Issues
Dave,
Thank you for taking the time to respond. As you suggested, I metered out t=
he green wires and found the one that was producing 12 volts. When I connec=
ted it to the one of the wires in the harness connected to the trans back u=
p lights, THEY WORKED!
The two remaining issuers are: no turn signals, period. Hazards only flash =
on he driver=E2=80=99s side. (Earlier I stated that I only had turn signals=
on the drivers side, but I was mistaken). A new turn signal module and haz=
ard module should arrive this weekend. Please share any other thoughts as t=
o the cause(s) of these issues.
Thanks again for your help.
Bob Fabie
On Fri, Jan 28, 2022 at 7:53 AM DAVID MASSEY <dave1massey@cs.com> wrote:
Here is a screen shot of the wiring to the transmission From Dan Master's =
handy wiring diagrams.=C2=A0 As you can see, there is a green wire (fused 1=
2 volts) to the switch and a Green/Brown wire which feeds power from the sw=
itch to the lights.=C2=A0 The Green wire should be hot anytime the key is o=
n.=C2=A0 The fuse that feeds it also feeds power to the heater fan, wipers,=
gauges, turn signals so if they work you are probably good.
Turn signals: are both lights not working or is it just one?=C2=A0 If one b=
ulb is not lighting up the other bulb will not draw enough current to cause=
the flasher to flash.
On the other hand, it might just be the bulbs or bulb sockets.=C2=A0 The so=
ckets are notoriously unreliable, especially when they get old.=C2=A0 The g=
round connection is the usual suspect.=C2=A0 Start there.=C2=A0 If you have=
a volt meter check for voltage on the wires where they plug onto the socke=
ts.
=20
Dave=20
=20
=20
-----Original Message-----
From: rmf3860 rmf3860 <bobfabie@gmail.com>
To: 6pack@autox.team.net <6pack@autox.team.net>
Sent: Thu, Jan 27, 2022 9:09 pm
Subject: [6pack] Two Issues
Hello All,
As you may know from my earlier post, by TR6 is alive and running beautiful=
ly following an extensive engine rebuild that ended up taking a few years, =
rather than the few months I had envisioned. Life and other important thing=
s interfered. Imagine that=E2=80=A6
I=E2=80=99m now finishing up the final details and have encountered two iss=
ues, probably unrelated, that I need your help in diagnosing.=C2=A0
First: Only my left turn signal works and the hazard light doesn=E2=80=99t =
work at all.=C2=A0
Second: The back-up lights don=E2=80=99t work. I=E2=80=99ve installed a new=
back up light harness. I=E2=80=99ve tried to study the wiring diagram but =
can=E2=80=99t quite figure out how the 3 wires connect to the main harness=
=E2=80=99 3 bullet connectors in the passenger foot well area. I can see th=
at two of the new harness wires are solid green and the other has a ?red? t=
hread. The main harness wires are almost impossible to discern which are so=
lid and which has a different color thread.
Can anyone help me sort out these issues?
Thanks.Bob FabieFredericksburg, VA
_______________________________________________
Archive: http://www.team.net/archive
6pack@autox.team.net
http://autox.team.net/mailman/listinfo/6pack
@cs.com
------=_Part_3840676_565455535.1643463536131
Content-Transfer-Encoding: quoted-printable
<div style=3D"color:black;font: 12pt Arial, Helvetica, sans-serif;">
<div> <font size=3D"3">OK. No turn signals at all may be the hazard s=
witch. The hazard switch disconnects the turn signal flasher. I=
f those contacts are dodgy the turn signals won't work. If the contac=
ts for the right side are dodgy they won't work in the hazard mode. I=
'd start there.</font><br>
</div>
<div> <br>
</div>
<div style=3D"clear:both"><font size=3D"4">Dave </font><br>
<br>
</div>
<div> <br>
</div>
<div> <br>
</div>
<div style=3D"font-family:arial,helvetica;font-size:10pt;color:black"><font=
size=3D"2">-----Original Message-----<br>
From: rmf3860 rmf3860 <bobfabie@gmail.com><br>
To: DAVID MASSEY <dave1massey@cs.com><br>
Cc: 6pack@autox.team.net <6pack@autox.team.net><br>
Sent: Fri, Jan 28, 2022 6:11 pm<br>
Subject: Re: [6pack] Two Issues<br>
<br>
<div id=3D"yiv2214982056">
<div>
<div>Dave,</div>
<div><br clear=3D"none"></div>
<div>Thank you for taking the time to respond. As you suggested, I metered =
out the green wires and found the one that was producing 12 volts. When I c=
onnected it to the one of the wires in the harness connected to the trans b=
ack up lights, THEY WORKED!</div>
<div><br clear=3D"none"></div>
<div>The two remaining issuers are: no turn signals, period. Hazards only f=
lash on he driver=E2=80=99s side. (Earlier I stated that I only had turn si=
gnals on the drivers side, but I was mistaken). A new turn signal module an=
d hazard module should arrive this weekend. Please share any other thoughts=
as to the cause(s) of these issues.</div>
<div><br clear=3D"none"></div>
<div>Thanks again for your help.</div>
<div><br clear=3D"none"></div>
<div>Bob Fabie</div>
<div id=3D"yiv2214982056yqt03439" class=3D"yiv2214982056yqt3199969957">
<div><br clear=3D"none">
<div class=3D"yiv2214982056gmail_quote">
<div dir=3D"ltr" class=3D"yiv2214982056gmail_attr">On Fri, Jan 28, 2022 at =
7:53 AM DAVID MASSEY <<a rel=3D"nofollow noopener noreferrer" shape=3D"r=
ect" ymailto=3D"mailto:dave1massey@cs.com"; target=3D"_blank" href=3D"mailto=
:dave1massey@cs.com">dave1massey@cs.com</a>> wrote:<br clear=3D"none"></=
div>
<blockquote style=3D"margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-l=
eft:1ex;" class=3D"yiv2214982056gmail_quote">
<div style=3D"color:black;font:12pt Arial, Helvetica, sans-serif;">
<div> <img alt=3D""></div>
<div><font size=3D"3">Here is a screen shot of the wiring to the transmissi=
on From Dan Master's handy wiring diagrams. As you can see, there is =
a green wire (fused 12 volts) to the switch and a Green/Brown wire which fe=
eds power from the switch to the lights. The Green wire should be hot=
anytime the key is on. The fuse that feeds it also feeds power to th=
e heater fan, wipers, gauges, turn signals so if they work you are probably=
good.</font></div>
<div><br clear=3D"none">
</div>
<div><font size=3D"3">Turn signals: are both lights not working or is it ju=
st one? If one bulb is not lighting up the other bulb will not draw e=
nough current to cause the flasher to flash.</font></div>
<div><br clear=3D"none">
</div>
<div><font size=3D"3">On the other hand, it might just be the bulbs or bulb=
sockets. The sockets are notoriously unreliable, especially when the=
y get old. The ground connection is the usual suspect. Start th=
ere. If you have a volt meter check for voltage on the wires where th=
ey plug onto the sockets.</font><br clear=3D"none">
</div>
<div> <br clear=3D"none">
</div>
<div style=3D"clear:both;"><font size=3D"4">Dave </font><br clear=3D"none">
<br clear=3D"none">
</div>
<div> <br clear=3D"none">
</div>
<div> <br clear=3D"none">
</div>
<div style=3D"font-family:arial, helvetica;font-size:10pt;color:black;"><fo=
nt size=3D"2">-----Original Message-----<br clear=3D"none">
From: rmf3860 rmf3860 <<a rel=3D"nofollow noopener noreferrer" shape=3D"=
rect" ymailto=3D"mailto:bobfabie@gmail.com"; target=3D"_blank" href=3D"mailt=
o:bobfabie@gmail.com">bobfabie@gmail.com</a>><br clear=3D"none">
To: <a rel=3D"nofollow noopener noreferrer" shape=3D"rect" ymailto=3D"mailt=
o:6pack@autox.team.net" target=3D"_blank" href=3D"mailto:6pack@autox.team.n=
et">6pack@autox.team.net</a> <<a rel=3D"nofollow noopener noreferrer" sh=
ape=3D"rect" ymailto=3D"mailto:6pack@autox.team.net"; target=3D"_blank" href=
=3D"mailto:6pack@autox.team.net";>6pack@autox.team.net</a>><br clear=3D"n=
one">
Sent: Thu, Jan 27, 2022 9:09 pm<br clear=3D"none">
Subject: [6pack] Two Issues<br clear=3D"none">
<br clear=3D"none">
</font></div>
</div>
<div style=3D"color:black;font:12pt Arial, Helvetica, sans-serif;">
<div style=3D"font-family:arial, helvetica;font-size:10pt;color:black;"><fo=
nt size=3D"2"></font>
<div id=3D"yiv2214982056m_-4817526784323085801yiv3079743941">Hello All,
<div><br clear=3D"none">
</div>
<div>As you may know from my earlier post, by TR6 is alive and running beau=
tifully following an extensive engine rebuild that ended up taking a few ye=
ars, rather than the few months I had envisioned. Life and other important =
things interfered. Imagine that=E2=80=A6</div>
<div><br clear=3D"none">
</div>
<div>I=E2=80=99m now finishing up the final details and have encountered tw=
o issues, probably unrelated, that I need your help in diagnosing. </d=
iv>
<div><br clear=3D"none">
</div>
<div>First: Only my left turn signal works and the hazard light doesn=E2=80=
=99t work at all. </div>
<div><br clear=3D"none">
</div>
<div>Second: The back-up lights don=E2=80=99t work. I=E2=80=99ve installed =
a new back up light harness. I=E2=80=99ve tried to study the wiring diagram=
but can=E2=80=99t quite figure out how the 3 wires connect to the main har=
ness=E2=80=99 3 bullet connectors in the passenger foot well area. I can se=
e that two of the new harness wires are solid green and the other has a ?re=
d? thread. The main harness wires are almost impossible to discern which ar=
e solid and which has a different color thread.</div>
<div><br clear=3D"none">
</div>
<div>Can anyone help me sort out these issues?</div>
<div><br clear=3D"none">
</div>
<div>Thanks.</div>
<div>Bob Fabie</div>
<div>Fredericksburg, VA</div>
<div><br clear=3D"none">
</div>
</div>
</div>
</div>
<div style=3D"color:black;font:12pt Arial, Helvetica, sans-serif;">
<div style=3D"font-family:arial, helvetica;font-size:10pt;color:black;"><fo=
nt size=3D"2">
_______________________________________________<br clear=3D"none">
get=3D"_blank" href=3D"http://www.team.net/donate.html";>http://www.team.net=
/donate.html</a><br clear=3D"none">
Archive: <a rel=3D"nofollow noopener noreferrer" shape=3D"rect" target=3D"_=
blank" href=3D"http://www.team.net/archive";>http://www.team.net/archive</a>=
<br clear=3D"none">
<br clear=3D"none">
<br clear=3D"none">
<a rel=3D"nofollow noopener noreferrer" shape=3D"rect" ymailto=3D"mailto:6p=
ack@autox.team.net" target=3D"_blank" href=3D"mailto:6pack@autox.team.net";>=
6pack@autox.team.net</a><br clear=3D"none">
<a rel=3D"nofollow noopener noreferrer" shape=3D"rect" target=3D"_blank" hr=
ef=3D"http://autox.team.net/mailman/listinfo/6pack";>http://autox.team.net/m=
ailman/listinfo/6pack</a><br clear=3D"none">
<br clear=3D"none">
target=3D"_blank" href=3D"http://autox.team.net/mailman/options/6pack/dave1=
massey@cs.com">http://autox.team.net/mailman/options/6pack/dave1massey@cs.c=
om</a><br clear=3D"none">
<br clear=3D"none">
</font></div>
</div>
</blockquote></div>
</div>
</div>
</div>
</div>
</font></div>
</div>
------=_Part_3840676_565455535.1643463536131--
--===============6819687154380231599==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/archive
6pack@autox.team.net
http://autox.team.net/mailman/listinfo/6pack
--===============6819687154380231599==--
|