--===============0255603802427786735==
--001a113532ea879bd6053b12a20e
Content-Transfer-Encoding: quoted-printable
Most of us have done the same thing. The offset still allows it to be
installed 180 degrees out.
On Friday, August 26, 2016, Jon Paschke via Spridgets <
spridgets@autox.team.net> wrote:
> Thanks everyone, got it. We took the dristrubitor drive out and realigned
> it and put everything back together and now the mark alines and we have t=
he
> timing set. It must be windows related, a reboot and all is well.
> Just a Spridget owner miss step...;)
> As a side note on this 1275 we rebuilt, we had it built two weeks ago and
> started it only to have it cease up after about 15 seconds. Tore it back
> down only to find the wrist pins had frozen in the pistons 2, 3, and 4.
> We had a machine shop install the pistons on the rods and they supplied
> new pistons when they did it so they redid them and gave us a new set of
> pistons as they had to destroy the frozen on ones.
> They said the factory clearance must have been to close on the bad set.
> Thanks for all the ideas and responses.
> Jon
> 58 Bugeye
>
> On 8/26/2016 2:06 PM, Gerard pixelsmith@gerardsgarage.com
> <javascript:_e(%7B%7D,'cvml','pixelsmith@gerardsgarage.com');> [bugeye]
> wrote:
>
>
>
> Jon,
>
> Either the mark you are looking at is not the original one or the rubber
> isolation ring has deteriorated enough to let the inner and out portion
> slip out of alignment. The original timing mark on a 1275 is a small squa=
re
> notch at the back end (nearest the timing cover) of the pulley. If I
> remember correctly, the timing mark should be directly in line, and
> opposite the keyway.
>
> Gerard
>
> > On Aug 26, 2016, at 1:55 PM, Jon Paschke JPASCHKE@bak.rr.com
> <javascript:_e(%7B%7D,'cvml','JPASCHKE@bak.rr.com');> [bugeye]
> <bugeye@yahoogroups.com>
> <javascript:_e(%7B%7D,'cvml','bugeye@yahoogroups.com');> wrote:
> >
> > Hi
> > I've just rebuilt my 1275 and it started right up and we broke in the
> > cam with no problems. After shutting it down and it cooled off we put
> > the timing light on it and the marks are at least 2 inches apart and
> > when I try moving the distributor to get them close the motor will not
> > run. What did I do? it seems like it's about a quarter of the bottom
> > pulley off. I have the distributor aligned according to the book and th=
e
> > rotor points right at number one at TDC. I have a pertronics in it and
> > it ran fine and timed right before the rebuild. Could the cam be off?
> > Thanks in advance,
> > Jon
> >
> >
> >
> > ------------------------------------
> > Posted by: Jon Paschke <jpaschke@bak.rr.com>
> <javascript:_e(%7B%7D,'cvml','jpaschke@bak.rr.com');>
> > ------------------------------------
> >
> > If you wish to unsubscribe from the Austin Healey Bugeye Frogeye Sprite
> Club, please send a blank email to: bugeye-unsubscribe@yahoogroups.com
> <javascript:_e(%7B%7D,'cvml','bugeye-unsubscribe@yahoogroups.com');>
> > If you no longer want to receive emails, but wish to remain a member of
> the group, you may go to the website http://groups.yahoo.com/group/bugeye=
/
> and change your subscription to "Web Only" and you will not receive any
> emails.
> >
> > ------------------------------------
> >
> > Yahoo Groups Links
> >
> >
> >
>
> __._,_.___
> ------------------------------
> Posted by: Gerard <pixelsmith@gerardsgarage.com>
> <javascript:_e(%7B%7D,'cvml','pixelsmith@gerardsgarage.com');>
> ------------------------------
> Reply via web post
> <https://groups.yahoo.com/neo/groups/bugeye/conversations/messages/43661;=
_ylc=3DX3oDMTJxNm5lYmp0BF9TAzk3MzU5NzE0BGdycElkAzI2NzQ2NDAEZ3Jwc3BJZAMxNzA2=
MDM0NDQ2BG1zZ0lkAzQzNjYxBHNlYwNmdHIEc2xrA3JwbHkEc3RpbWUDMTQ3MjI0NTYyMw--?ac=
t=3Dreply&messageNum=3D43661>
> =E2=80=A2 Reply to sender
> <javascript:_e(%7B%7D,'cvml','pixelsmith@gerardsgarage.com?subject%5Cx3dR=
e:+Bugeye/Frogeye+Club.....+Timing+marks+don%5Cx27t+align');>
> =E2=80=A2 Reply to group
> <javascript:_e(%7B%7D,'cvml','bugeye@yahoogroups.com?subject%5Cx3dRe:+Bug=
eye/Frogeye+Club.....+Timing+marks+don%5Cx27t+align');>
> =E2=80=A2 Start a New Topic
> <https://groups.yahoo.com/neo/groups/bugeye/conversations/newtopic;_ylc=
=3DX3oDMTJlMzh2bTZ2BF9TAzk3MzU5NzE0BGdycElkAzI2NzQ2NDAEZ3Jwc3BJZAMxNzA2MDM0=
NDQ2BHNlYwNmdHIEc2xrA250cGMEc3RpbWUDMTQ3MjI0NTYyMw-->
> =E2=80=A2 Messages in this topic
> <https://groups.yahoo.com/neo/groups/bugeye/conversations/topics/43660;_y=
lc=3DX3oDMTM2bHNuOHNuBF9TAzk3MzU5NzE0BGdycElkAzI2NzQ2NDAEZ3Jwc3BJZAMxNzA2MD=
M0NDQ2BG1zZ0lkAzQzNjYxBHNlYwNmdHIEc2xrA3Z0cGMEc3RpbWUDMTQ3MjI0NTYyMwR0cGNJZ=
AM0MzY2MA-->
> (2)
> ------------------------------
> Have you tried the highest rated email app? <https://yho.com/1wwmgg>
> With 4.5 stars in iTunes, the Yahoo Mail app is the highest rated email
> app on the market. What are you waiting for? Now you can access all your
> inboxes (Gmail, Outlook, AOL and more) in one place. Never delete an emai=
l
> again with 1000GB of free cloud storage.
> ------------------------------
> If you wish to unsubscribe from the Austin Healey Bugeye Frogeye Sprite
> Club, please send a blank email to: bugeye-unsubscribe@yahoogroups.com
> <javascript:_e(%7B%7D,'cvml','bugeye-unsubscribe@yahoogroups.com');>
> If you no longer want to receive emails, but wish to remain a member of
> the group, you may go to the website http://groups.yahoo.com/group/bugeye=
/
> and change your subscription to "Web Only" and you will not receive any
> emails.
> Visit Your Group
> <https://groups.yahoo.com/neo/groups/bugeye/info;_ylc=3DX3oDMTJlNm91aDZzB=
F9TAzk3MzU5NzE0BGdycElkAzI2NzQ2NDAEZ3Jwc3BJZAMxNzA2MDM0NDQ2BHNlYwN2dGwEc2xr=
A3ZnaHAEc3RpbWUDMTQ3MjI0NTYyMw-->
>
>
> [image: Yahoo! Groups]
> <https://groups.yahoo.com/neo;_ylc=3DX3oDMTJkNmVvbDJkBF9TAzk3MzU5NzE0BGdy=
cElkAzI2NzQ2NDAEZ3Jwc3BJZAMxNzA2MDM0NDQ2BHNlYwNmdHIEc2xrA2dmcARzdGltZQMxNDc=
yMjQ1NjIz>
> =E2=80=A2 Privacy <https://info.yahoo.com/privacy/us/yahoo/groups/details=
.html> =E2=80=A2
> Unsubscribe
> <javascript:_e(%7B%7D,'cvml','bugeye-unsubscribe@yahoogroups.com?subject%=
5Cx3dUnsubscribe');>
> =E2=80=A2 Terms of Use <https://info.yahoo.com/legal/us/yahoo/utos/terms/=
>
>
> .
>
> __,_._,___
>
>
>
--001a113532ea879bd6053b12a20e
Content-Transfer-Encoding: quoted-printable
Most of us have done the same thing. The offset still allows it to be insta=
lled 180 degrees out.=C2=A0<br><br>On Friday, August 26, 2016, Jon Paschke =
via Spridgets <<a href=3D"mailto:spridgets@autox.team.net";>spridgets@aut=
ox.team.net</a>> wrote:<br><blockquote class=3D"gmail_quote" style=3D"ma=
rgin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
=20
=20
=20
<div bgcolor=3D"#FFFFFF" text=3D"#000000">
<div>Thanks everyone, got it. We took the
dristrubitor drive out and realigned it and put everything back
together and now the mark alines and we have the timing set. It
must be windows related, a reboot and all is well. <br>
Just a Spridget owner miss step...;)<br>
As a side note on this 1275 we rebuilt, we had it built two weeks
ago and started it only to have it cease up after about 15
seconds. Tore it back down only to find the wrist pins had frozen
in the pistons 2, 3, and 4. <br>
We had a machine shop install the pistons on the rods and they
supplied new pistons when they did it so they redid them and gave
us a new set of pistons as they had to destroy the frozen on ones.<br=
>
They said the factory clearance must have been to close on the bad
set.<br>
Thanks for all the ideas and responses.<br>
Jon<br>
58 Bugeye<br>
<br>
On 8/26/2016 2:06 PM, Gerard <a href=3D"javascript:_e(%7B%7D,'cvm=
l','pixelsmith@gerardsgarage.com');" target=3D"_blank">pixelsmi=
th@gerardsgarage.com</a> [bugeye]
wrote:<br>
</div>
<blockquote type=3D"cite"> <span style=3D"display:none">=C2=A0</span>
=20
<div>
<div>
=20
<div>
<p>Jon,<br>
<br>
Either the mark you are looking at is not the original one
or the rubber isolation ring has deteriorated enough to
let the inner and out portion slip out of alignment. The
original timing mark on a 1275 is a small square notch at
the back end (nearest the timing cover) of the pulley. If
I remember correctly, the timing mark should be directly
in line, and opposite the keyway.<br>
<br>
Gerard<br>
<br>
> On Aug 26, 2016, at 1:55 PM, Jon Paschke
<a href=3D"javascript:_e(%7B%7D,'cvml','JPASCHKE@=
bak.rr.com');" target=3D"_blank">JPASCHKE@bak.rr.com</a> [bugeye]
<a href=3D"javascript:_e(%7B%7D,'cvml','bugeye@ya=
hoogroups.com');" target=3D"_blank"><bugeye@yahoogroups.com></a> =
wrote:<br>
> <br>
> Hi<br>
> I've just rebuilt my 1275 and it started right up an=
d
we broke in the <br>
> cam with no problems. After shutting it down and it
cooled off we put <br>
> the timing light on it and the marks are at least 2
inches apart and <br>
> when I try moving the distributor to get them close
the motor will not <br>
> run. What did I do? it seems like it's about a
quarter of the bottom <br>
> pulley off. I have the distributor aligned according
to the book and the <br>
> rotor points right at number one at TDC. I have a
pertronics in it and <br>
> it ran fine and timed right before the rebuild. Could
the cam be off?<br>
> Thanks in advance,<br>
> Jon<br>
> <br>
> <br>
> <br>
> ------------------------------<wbr>------<br>
> Posted by: Jon Paschke <a href=3D"javascript:_e(%7B%7D,&=
#39;cvml','jpaschke@bak.rr.com');" target=3D"_blank"><jpasch=
ke@bak.rr.com></a><br>
> ------------------------------<wbr>------<br>
> <br>
> If you wish to unsubscribe from the Austin Healey
Bugeye Frogeye Sprite Club, please send a blank email to:
<a href=3D"javascript:_e(%7B%7D,'cvml','bugeye-un=
subscribe@yahoogroups.com');" target=3D"_blank">bugeye-unsubscribe@<wbr=
>yahoogroups.com</a><br>
> If you no longer want to receive emails, but wish to
remain a member of the group, you may go to the website
<a href=3D"http://groups.yahoo.com/group/bugeye/"; target=3D"_=
blank">http://groups.yahoo.com/group/<wbr>bugeye/</a> and change your
subscription to "Web Only" and you will not receive=
any
emails.<br>
> <br>
> ------------------------------<wbr>------<br>
> <br>
> Yahoo Groups Links<br>
> <br>
> <br>
> <br>
<br>
</p>
</div>
=20
<div style=3D"color:#fff;min-height:0">__._,_.___</div>
<div style=3D"clear:both"> </div>
<div style=3D"margin-top:10px">
<hr style=3D"min-height:2px;border-width:0;color:#e3e3e3;backgr=
ound-color:#e3e3e3"> Posted by: Gerard
<a href=3D"javascript:_e(%7B%7D,'cvml','pixelsmith@=
gerardsgarage.com');" target=3D"_blank"><pixelsmith@gerardsgarage.co=
m></a>
<hr style=3D"min-height:2px;border-width:0;color:#e3e3e3;backgr=
ound-color:#e3e3e3"> </div>
<div style=3D"clear:both"> </div>
<table style=3D"margin-top:10px;margin-bottom:10px;color:#2d50fd"=
cellspacing=3D"4px">
<tbody>
<tr>
<td style=3D"font-size:12px;font-family:arial;font-weight:b=
old;padding:7px 5px 5px"> <a style=3D"text-decoration:none;color:#2d50fd" h=
ref=3D"https://groups.yahoo.com/neo/groups/bugeye/conversations/messages/43=
661;_ylc=3DX3oDMTJxNm5lYmp0BF9TAzk3MzU5NzE0BGdycElkAzI2NzQ2NDAEZ3Jwc3BJZAMx=
NzA2MDM0NDQ2BG1zZ0lkAzQzNjYxBHNlYwNmdHIEc2xrA3JwbHkEc3RpbWUDMTQ3MjI0NTYyMw-=
-?act=3Dreply&messageNum=3D43661" target=3D"_blank">Reply
via web post</a> </td>
<td>=E2=80=A2</td>
<td style=3D"font-size:12px;font-family:arial;padding:7px 5=
px 5px"> <a href=3D"javascript:_e(%7B%7D,'cvml','pixelsmith@ger=
ardsgarage.com?subject%5Cx3dRe:+Bugeye/Frogeye+Club.....+Timing+marks+don%5=
Cx27t+align');" style=3D"text-decoration:none;color:#2d50fd" target=3D"=
_blank">
Reply to sender </a> </td>
<td>=E2=80=A2</td>
<td style=3D"font-size:12px;font-family:arial;padding:7px 5=
px 5px"> <a href=3D"javascript:_e(%7B%7D,'cvml','bugeye@yahoogr=
oups.com?subject%5Cx3dRe:+Bugeye/Frogeye+Club.....+Timing+marks+don%5Cx27t+=
align');" style=3D"text-decoration:none;color:#2d50fd" target=3D"_blank=
"> Reply
to group </a> </td>
<td>=E2=80=A2</td>
<td style=3D"font-size:12px;font-family:arial;padding:7px 5=
px 5px"> <a href=3D"https://groups.yahoo.com/neo/groups/bugeye/conversation=
s/newtopic;_ylc=3DX3oDMTJlMzh2bTZ2BF9TAzk3MzU5NzE0BGdycElkAzI2NzQ2NDAEZ3Jwc=
3BJZAMxNzA2MDM0NDQ2BHNlYwNmdHIEc2xrA250cGMEc3RpbWUDMTQ3MjI0NTYyMw--" style=
=3D"text-decoration:none;color:#2d50fd" target=3D"_blank">Start
a New Topic</a> </td>
<td>=E2=80=A2</td>
<td style=3D"font-size:12px;font-family:arial;padding:7px 5=
px 5px;color:#2d50fd"> <a href=3D"https://groups.yahoo.com/neo/groups/bugey=
e/conversations/topics/43660;_ylc=3DX3oDMTM2bHNuOHNuBF9TAzk3MzU5NzE0BGdycEl=
kAzI2NzQ2NDAEZ3Jwc3BJZAMxNzA2MDM0NDQ2BG1zZ0lkAzQzNjYxBHNlYwNmdHIEc2xrA3Z0cG=
MEc3RpbWUDMTQ3MjI0NTYyMwR0cGNJZAM0MzY2MA--" style=3D"text-decoration:none;c=
olor:#2d50fd" target=3D"_blank">Messages
in this topic</a> (2) </td>
</tr>
</tbody>
</table>
<div>
<hr style=3D"min-height:2px;border-width:0;color:#e3e3e3;backgr=
ound-color:#e3e3e3">
<div>
<div style=3D"margin-bottom:10px">
<div style=3D"background-color:white">
<div style=3D"display:inline"><img name=3D"m_-54036088644=
99339655_tn_file" style=3D"padding:0px 10px;vertical-align:top;margin-top:5=
px" src=3D"https://s.yimg.com/ru/static/images/yg/img/megaphone/1464031581_=
phpFA8bON" height=3D"82" width=3D"82"></div>
<div style=3D"display:inline-block"> <a rel=3D"nofollow" =
name=3D"m_-5403608864499339655_sub_url" href=3D"https://yho.com/1wwmgg"; sty=
le=3D"color:#0000ff;display:block;margin-left:5px;text-decoration:none" tar=
get=3D"_blank"><span style=3D"font-size:15px">Have you tried the
highest rated email app?</span></a>
<div style=3D"max-width:530px;padding:2px 5px">With
4.5 stars in iTunes, the Yahoo Mail app is the
highest rated email app on the market. What are
you waiting for? Now you can access all your
inboxes (Gmail, Outlook, AOL and more) in one
place. Never delete an email again with 1000GB of
free cloud storage.</div>
</div>
</div>
</div>
</div>
<hr style=3D"min-height:2px;border-width:0;color:#e3e3e3;backgr=
ound-color:#e3e3e3">
</div>
=20
=20
=20
<div style=3D"font-family:Verdana;font-size:12px;padding:15px 0">
If you wish to
unsubscribe from the Austin Healey Bugeye Frogeye Sprite
Club, please send a blank email to:=C2=A0
<a href=3D"javascript:_e(%7B%7D,'cvml','bugeye-unsu=
bscribe@yahoogroups.com');" target=3D"_blank">bugeye-unsubscribe@<wbr>y=
ahoogroups.com</a><br>
If you no longer want to receive emails, but wish to remain
a member of the group, you may go to the website <a href=3D"htt=
p://groups.yahoo.com/group/bugeye/" target=3D"_blank">http://groups.yahoo.c=
om/group/<wbr>bugeye/</a>
and change your subscription to "Web Only" and you wi=
ll not
receive any emails.<br>
</div>
=20
<div style=3D"background-color:#f2f2f2;font-family:Verdana;font-s=
ize:10px;margin-bottom:10px;padding:10px"> <span style=3D"font-weight:bold;=
color:#333;text-transform:uppercase"><a href=3D"https://groups.yahoo.com/ne=
o/groups/bugeye/info;_ylc=3DX3oDMTJlNm91aDZzBF9TAzk3MzU5NzE0BGdycElkAzI2NzQ=
2NDAEZ3Jwc3BJZAMxNzA2MDM0NDQ2BHNlYwN2dGwEc2xrA3ZnaHAEc3RpbWUDMTQ3MjI0NTYyMw=
--" style=3D"text-decoration:none" target=3D"_blank">Visit Your Group</a></=
span>
<ul style=3D"list-style-type:none;margin:0;padding:0;display:in=
line">
</ul>
</div>
<div style=3D"font-family:Arial;font-size:11px;margin-top:5px;pad=
ding:0 2px 0 0;clear:both"> <a href=3D"https://groups.yahoo.com/neo;_ylc=3D=
X3oDMTJkNmVvbDJkBF9TAzk3MzU5NzE0BGdycElkAzI2NzQ2NDAEZ3Jwc3BJZAMxNzA2MDM0NDQ=
2BHNlYwNmdHIEc2xrA2dmcARzdGltZQMxNDcyMjQ1NjIz" style=3D"float:left" target=
=3D"_blank"><img src=3D"http://l.yimg.com/ru/static/images/yg/img/email/new=
_logo/logo-groups-137x15.png" alt=3D"Yahoo! Groups" style=3D"border:0" heig=
ht=3D"15" width=3D"137"></a>
<div style=3D"color:#747575;float:right"> =E2=80=A2 <a href=3D"=
https://info.yahoo.com/privacy/us/yahoo/groups/details.html"; style=3D"text-=
decoration:none" target=3D"_blank">Privacy</a> =E2=80=A2 <a href=3D"javascr=
ipt:_e(%7B%7D,'cvml','bugeye-unsubscribe@yahoogroups.com?subjec=
t%5Cx3dUnsubscribe');" style=3D"text-decoration:none" target=3D"_blank"=
>Unsubscribe</a> =E2=80=A2 <a href=3D"https://info.yahoo.com/legal/us/yahoo=
/utos/terms/" style=3D"text-decoration:none" target=3D"_blank">Terms of Use=
</a> </div>
</div>
<br>
</div>
=20
=20
=20
<div style=3D"width:160px;float:right;clear:none;margin:0 0 25px 0;=
background:#fff">
=20
<div> </div>
</div>
=20
<div style=3D"clear:both;color:#fff;font-size:1px">.</div>
</div>
<img height=3D"1" width=3D"1"> <br>
<img height=3D"1" width=3D"1">
<div style=3D"color:#fff;min-height:0">__,_._,___</div>
=20
=20
=20
=20
=20
</blockquote>
<br>
</div>
</blockquote>
--001a113532ea879bd6053b12a20e--
--===============0255603802427786735==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
------------------------
spridgets@autox.team.net
Archive: http://www.team.net/archive
--===============0255603802427786735==--
|