Shouldn't the filter be at the inlet? (see photo)
I'll get some 90 degree elbows regular plumbing fitting right? Also the
instructions indicate the pump needs to be at the horizontal position, but I
will reread it.
Are the threads to the tank available locally or some funky thread I need to
order (from where?) If I cut that steel line and damage it can I pick up the
line at a local auto shop and they bend it on a bender? I always remember
how Frank said the threads in the tank are unobtainable that is why this
stresses me out.
Peter Caldwell thanks I'll call from school today.
Lin
On Mon, May 16, 2011 at 10:11 AM, Mark Haynes <haynes386@netzero.net> wrote:
> Lin-
> If you turn the pump 90*, so that the inlet filter is pointing upwards, the
> incoming line will JUST make the turn without kinking. Also, if you shift
> the whole shebang outboard, it'll make the two hose radii more manageable. I
> used nutserts for mine in just that position on my MKII, that makes it
> easier to remove and replace the filter.
> Is Pinky Neg or Pos ground? Those pumps need to be wired correctly (ask me
> how I know) or they'll crap out within 100 miles or so. I also always mount
> mine on electric motor isolators so they aren't so loud, and mount a fuel
> pump switch for those times when I want to turn the engine without fuel.
>
>
> Mark Haynes
> It only goes one way-Pay it Forward
> HAN6L12977
> HAN5L8016
>
> Message: 14
> Date: Sat, 14 May 2011 22:01:34 -0400
> From: Linda Grunthaner <grunthaner@gmail.com>
> Subject: [Spridgets] Tips or examples installing my Facet pump, hose
> never fits right.
> To: Spridget list <spridgets@autox.team.net>
> Message-ID: <BANLkTinDOFSE8euAoT4zaBT_poMiZxJvNw@mail.gmail.com>
> Content-Type: text/plain; charset="us-ascii"
>
> List,
> I am installing my new Facet fuel pump in the rear like the later Spridgets
> and came to a small road block. Below are photos of the location and the
> new
> pump for a better visual. I drained the tank today (the crap ran down my
> arm
> so i am soaked with gas (good thing I quit smoking again this week) and I
> was getting ready to cut the fuel line but noticed when I place the pump in
> position it is very cramped and I don't see how to get rubber line in
> correctly without kinking the line for that 90 degree turn. I couldn't get
> to the store in time but I'll try and get a fitting with a 90 degree which
> I'm sure they won't have the correct thread size or the end will be huge. I
> also checked my rubber line and it is 1/4" as I recall our lines are
> smaller
> than stock fuel line and are a pain in the ass to fit because we end up
> with
> larger hose. Is there a specialty parts shop who will have a fitting for
> small hose?
>
> Why is this such a PITA it just shouldn't be. Looking at the filter that
> came with the pump I won't be able to fit any hose on that monster can I
> remove the filter altogether or maybe get a fitting and a plastic filter?
> Also I remember an old post that said they make teflon tape for fuel, who
> would have that?
>
> If anyone can send me a photo of their setup I would be appreciative.
> Lin
>
> ____________________________________________________________
> Groupon™ Official Site
> 1 ridiculously huge coupon a day. Get 50-90% off your city's best!
> http://thirdpartyoffers.netzero.net/TGL3231/4dd130e833f764ac154st02duc
_______________________________________________
Donate: http://www.team.net/donate.html
Suggested annual donation $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
|