Bob,
The problem with your solution is you can't make the wipers go faster in
heavy rain.
They will never go faster than they did originally and THAT was the problem
as I
perceived it. The wipers on my 68 Midget are too slow in heavy rain. If I
had
a motor that would go much faster I could easily build a switch and resistor
set-up that would allow slower speeds. There are even under the dash
components
available out there that would allow intermittent settings but you are never
going
to get faster speeds out of the original motor.
Cheers!!
Jim
On Mon, Jan 31, 2011 at 10:07 PM, Bob Gardner <rdgard@cox.net> wrote:
> When you are at the water end of the SF Cable Car, especially in the winter
> months, walk across the street to the Buena Vista and order an Irish
> Coffee.
> They are world famous for that! They are wonderful.
>
> Now on to the Bugeye 2 speed wiper. The Bugeye came equipped with a 3
> speed
> wiper. Made by Lucas, it was 1. off, 2. sometimes slow with smoke, and 3.
> on.
>
> But seriously folks, why not do one of these tricks. When I wanted to have
> a multi speed wiper on our old VW beetles, I would just buy a headlight
> switch from any old American car. Built in to the switch is a wire wound
> rheostat made for dimming the dome light and the dash lights. Just wire
> that into the hot lead of the wiper motor and bingo, you can vary the speed
> as you like. In the case that the BE wiper motor draws too much current
> for
> the dimmer pot, They used to make heavy duty ones to control the heater
> speed. Check them out.
>
> Another easy fix is to ask a friend who knows a little math to use the
> Ohm's
> Law to calculate the power required for a resister to cut the speed in
> half,
> or down to what ever speed you desire. Then get a resister of the desired
> ohms, perhaps 150 ohms or 500 ohms, that should cut the speed in half. It
> will be important to get one with enough wattage, perhaps 10 watts power to
> not get too hot when running. Then wire a double pole, double throw toggle
> switch to switch the resister into and out of the power wire to the wiper.
> Bingo, $3 or 4 dollars of parts and it is done. If you don't want to drill
> a hole in the dash, put it on a little angle bracket just under the dash
> out
> of sight.
>
> As a shade tree way to determine the proper resistance to buy, using test
> clips, put a 110 volt 100 watt light bulb in series with the hot lead and
> check the speed. Use a higher wattage like 300 watt bulb for it to go
> faster and like a 25 watt bulb to go slower etc. When you select the right
> speed for you, take an ohm meter and measure the resistance of the bulb
> that
> works best and buy a 10 or 25 watt resister of the same ohms.
>
> Actually, now that I think about it, you can just wire both ends of the
> resister to the hot lead, then cut the hot lead in-between either end of
> the
> resister, then put a single pole single throw switch there and it will by
> pass the resister for full speed and when turned off, the current will then
> flow through the resister. Bingo!
>
> Some one should market that and sell them! I get 10%! lol
>
> Cheers,
>
> Bob in San Diego
>
> Robert D. Gardner
>
> Gardner Productions LLC
> Film and Video Production since 1978
> 619-460-1000
> www.gardnerproductions.com
>
> **********************************
> _______________________________________________
>
> Donate: http://www.team.net/donate.html
> Suggested annual donation $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage <http://www.team.net/forums%0AUnsubscribe/Manage>:
> http://autox.team.net/mailman/options/spridgets/bmwwxman@gmail.com
>
>
--
Cheers!!
Jim
Then there was the mind reader who moved to Washington, D.C. and couldn't
find work.
_______________________________________________
Donate: http://www.team.net/donate.html
Suggested annual donation $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
|