shotimes
[Top] [All Lists]

Re: [Shotimes] Help with lean condition

To: <Shotimes@autox.team.net>
Subject: Re: [Shotimes] Help with lean condition
From: "Mark Helpinstill" <mhelpinstill@patmedia.net>
Date: Sun, 10 Sep 2006 23:40:02 -0400
Kris and George,

Thanks for the suggestions.

Definitely cleared the codes each time.

Checked Bosch part #s online and at the store - seems to be correct.

Not willing to spend $500 on new cats.

Looked for vacuum leaks again today and found nothing.

Looks like I will be pulling the spout connector and hoping for the best.

Thanks
Mark
----- Original Message ----- 
From: "K. Angermeier" <kickinsho@charter.net>
To: "Mark Helpinstill" <mhelpinstill@patmedia.net>
Sent: Saturday, September 09, 2006 7:58 PM
Subject: Re: [Shotimes] Help with lean condition


> Hey Mark,
>
> I may be off on my suggestions, but they are just that, suggestions.
>
> Did you make sure to clear the codes after each time?
>
> Do you know if your catalytic converters are okay?
>
> My first suggestion was merely because it was something I didn't realize.
>
> My second suggestion is because that is exactly what we had to do with my 
> '93 ATX to get it to pass emissions.  We brought it to a local exhaust 
> shop who cut the bad ones out and welded new ones on.
>
> Don't know if it helps or not, just my experience.
>
> Good Luck
>
> Kris Angermeier
> Sheboygan, WI
>
> '91 Plus Wht/Blk
> '91 Plus Wht/Blk (crushed)
> '93 Ultra Red ATX
>
> "Women Who Behave Never Make History"
> ----- Original Message ----- 
> From: "Mark Helpinstill" <mhelpinstill@patmedia.net>
> To: <shotimes@autox.team.net>
> Sent: Saturday, September 09, 2006 6:04 PM
> Subject: [Shotimes] Help with lean condition
>
>
>>I am extremely frustrated today - driven to shop for new cars.
>>
>> Having trouble with my 94 MTX.  I failed emissions for high NOX (by only 
>> 10%),
>> so I replaced my original o2 sensors (175K mi) with the Bosch 13942.
>> Restarted and after going 10 miles got a check engine light.  Pulled 
>> codes and
>> got the 172 and 176 O2 sensor codes.  Pulled new o2 sensors and bench 
>> tested
>> using the shotimes procedure - both failed to show decent voltage change. 
>> I
>> returned them to autozone and got replacements today.  Just installed 
>> them and
>> no longer getting the CEL, but with the code scanner still getting the 
>> same
>> codes, plus engine running getting code 16 (does not exist apparently). 
>> Code
>> scanner is a high quality autoxray unit.
>>
>> Checked for vacuum leaks and cleaned MAF.  Still getting the same codes. 
>> Any
>> suggestions before dropping the car at a shop?  I reinstalled the 
>> original
>> ford O2 sensors and get no codes.  It will likely cost $200+ just to get
>> someone to look at it, and likely tell me nothing.
>>
>> Bottom line - I replace a good part with known good parts and now I have
>> codes.  It seems likely that I have had a lean condition and the new O2
>> sensors are more accurately reflecting that with a code.
>>
>> If no one has any ideas - what about suggestions for a cost effective 
>> shop in
>> central NJ?
>>
>> Thanks
>> Mark
>> _______________________________________________
>> Shotimes mailing list
>> Shotimes@autox.team.net
>> http://www.team.net/mailman/listinfo/shotimes
_______________________________________________
Shotimes mailing list
Shotimes@autox.team.net
http://www.team.net/mailman/listinfo/shotimes

<Prev in Thread] Current Thread [Next in Thread>