--===============1032046462874521677==
--000000000000cfe7b40638f679b0
I've got a puzzle...
tl;dr - should I try the plug first, skip ahead and replace the coil, or
is there something else I should try?
The patient is a Snapper rear-engine riding mower, a machine that's as
simple as can be. Powered by a B&S Intek 12.5 HP engine, another simple
machine.
My friend was cutting his grass and managed to get the grass chute tangled
up in some old fencing. He got it loose, and continued to mow. After a
short distance, the mower quit running and would not restart.
I brought it into my shop and we started troubleshooting. I first tried
ether - it seemed like it tried for a second, and then nothing. Pulled the
plug and it looked wet. Turned the engine over with the plug connected and
grounded, and observed a spark. Not a magnificent spark, but a spark.
Verified compression, but due to the position of the muffler, I could not
get *any* of my compression testers to seal in the hole well. But it
pushed against my finger with some force.
Moved to the carb. Pulled and inspected. Float working, jet clear.
Put it all back together, and nothing.
Pulled the ground wire off the magneto coil and no change.
So, I'm thinking weak coil. Not completely dead, but not working under
cylinder pressure. Something else I read suggested a bad plug - this one
was installed a month ago and has been working. Date code on the engine
indicates it was built on April Fools Day, 2008.
In the era of $15 lawn mower coils, I would throw one on with no qualms.
But at $40 or $50, I hesitate.
So, tl;dr - should I try the plug first, skip ahead and replace the coil,
or is there something else I should try?
--000000000000cfe7b40638f679b0
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr">I've got a puzzle...<div><br></div><div>=C2=A0tl;dr - =
should I try the plug first, skip ahead and replace the coil, or is there s=
omething else I should try?<br><br>The patient is a Snapper rear-engine rid=
ing mower, a machine that's as simple as can be.=C2=A0 Powered by a B&a=
mp;S Intek 12.5 HP engine, another simple machine.<br><br>My friend was cut=
ting his grass and managed to get the grass chute tangled up in some old fe=
ncing.=C2=A0 He got it loose, and continued to mow.=C2=A0 After a short dis=
tance, the mower quit running and would not restart.<br><br>I brought it in=
to my shop and we started troubleshooting. I first tried ether=C2=A0- it se=
emed like it tried for a second, and then nothing.=C2=A0 Pulled the plug an=
d it looked wet.=C2=A0 Turned the engine over with the=C2=A0plug connected =
and grounded, and observed a spark.=C2=A0 Not a magnificent spark, but a sp=
ark.=C2=A0=C2=A0<div><br></div><div>Verified compression, but due to the po=
sition of the muffler, I could not get *any* of my compression testers to s=
eal in the hole well.=C2=A0 But it pushed against my finger with some force=
.</div><div><br></div><div>Moved to the carb.=C2=A0 Pulled and inspected.=
=C2=A0 Float working, jet clear.</div><div><br></div><div>Put it all back t=
ogether, and nothing.=C2=A0=C2=A0<br><br>Pulled the ground wire off the mag=
neto coil and no change.<br><br>So, I'm thinking weak coil.=C2=A0 Not c=
ompletely dead, but not working under cylinder pressure.=C2=A0 Something el=
se I read suggested a bad plug - this one was installed a month ago and has=
been working.=C2=A0 Date code on the engine indicates it was built on Apri=
l Fools Day, 2008.<br><br>In the era of $15 lawn mower coils, I would throw=
one on with no qualms.=C2=A0 But at $40 or $50, I hesitate.<br><br>So,
=C2=A0tl;dr - should I try the plug first, skip ahead and replace the coil,=
or is there something else I should try?<br><br></div></div></div>
--000000000000cfe7b40638f679b0--
--===============1032046462874521677==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Shop-talk@autox.team.net
Archive: http://www.team.net/pipermail/shop-talk http://autox.team.net/archive
--===============1032046462874521677==--
|